Fix and Furrow
Advertise

Part of our Heating and Cooling guide

HVAC Fall Maintenance Checklist: October Through December

Book the tune-up in October, test heat in November, check safety devices in December, and adjust the plan if you live where winters are mild.

Save to Pinterest

We may earn a commission when you buy through links on this page. It never changes what we recommend. Learn more

Basement furnace with a fresh replacement filter ready to install before winter
Photo: Oleksandr Chernobai on Unsplash

The short answer

In October, change the filter, clear the outdoor unit, and book a tune-up before the first cold snap. In November, run the heat for 15 to 30 minutes and get any problem looked at. In December, test carbon monoxide and smoke alarms and settle your winter thermostat habits. Warm-climate heat pump homes follow the same order but skip furnace-specific work.

Typical cost
$10 to $60 for a filter; $100 to $250 for a professional tune-up
Time needed
A few hours of DIY work spread across three months
Skill level
Beginner

Key points

  • Book the professional tune-up in October, before the first cold snap fills technicians' schedules and while a repair can still wait a few days.
  • Run your heating for a full cycle in November on a mild day so problems show up before you depend on it.
  • Check the furnace filter monthly in winter, because the system runs more and loads the filter faster.
  • Heat pumps in mild climates still need a clear outdoor unit, a clear drain line, and a heating-mode test before the first cool night.
  • Test every carbon monoxide detector in December and replace any unit past the date printed on its label.
In this guide
  1. Why Is October the Right Time to Start HVAC Prep?
  2. October Checklist: Inspect, Clean, and Book Your Tune-Up
  3. November Checklist: Test Heating Before You Need It
  4. December Checklist: Safety Checks and Winter Settings
  5. How Do Cold-Climate and Warm-Climate Checklists Differ?
  6. What Heat Pump Maintenance Do Mild Climates Still Need?
  7. What Mistakes Shorten Winter System Life?

The most useful thing you can do this week is pick a date for a furnace tune-up or heat pump service visit, then put in a fresh furnace filter the same day. Everything else on this HVAC fall maintenance checklist builds on those two moves, and it's sequenced by month so nothing piles up in December.

Why Is October the Right Time to Start HVAC Prep?

October works because heating technicians are usually least busy before the first cold snap, and a problem you find can still wait a few days for a repair. Once overnight lows drop, no-heat calls surge and waits can stretch from days to weeks in some areas. Treat the first cold snap as your region's date, not the calendar's. For most homes, we'd book the visit in October rather than gamble on November.

The weather helps too. It's mild enough to open up the system and work around the outdoor unit in comfort.

October Checklist: Inspect, Clean, and Book Your Tune-Up

In October, change the filter, clear the outdoor unit, check vents and exhaust pipes, and book the professional tune-up. Work in this order:

  1. Change the furnace filter. Check the size printed on the frame. One-inch filters usually need replacing every 1 to 3 months, while 4-inch media filters often last 6 to 12 months, so follow the maker's guidance. A clogged filter restricts airflow, which can make a furnace overheat and shut down on its safety limit.
  2. Clean the outdoor condenser before winter. Clear leaves, grass clippings, and debris from around and on top of the unit, and trim plants back about 2 feet on all sides. Rinse the fins gently with a garden hose, never a pressure washer. Do it before the first freeze, because wet leaves frozen against the coil block airflow, and on a heat pump that coil is your heat source.
  3. Walk the house for blocked vents. Move rugs, furniture, and boxes off supply registers and return grilles. Blocked returns starve the system of air.
  4. Check outdoor exhaust and intake pipes. High-efficiency furnaces usually vent through white PVC pipes on an exterior wall. Clear leaves, nests, and clutter from the openings so combustion gases can leave and fresh air can get in.
  5. Book the tune-up. A typical visit runs about $100 to $250, depending on region and whether it covers a furnace, a heat pump, or both. Ask what's included: burner and ignition check, combustion and carbon monoxide readings, blower and capacitor testing, drain inspection, and a look at the heat exchanger. A cracked heat exchanger is a job for a licensed technician, never a DIY call.

November Checklist: Test Heating Before You Need It

In November, run your heating through a full cycle on a mild day so any failure shows up while you can still get a technician within a few days. Set the thermostat to heat, about 5 degrees above room temperature, then listen and watch for 15 to 30 minutes.

A light burning-dust smell during the first hour is normal after months idle. Banging, repeated starts and stops, a yellow or flickering burner flame (it should be steady blue), or no warm air at all are not. Call a technician for any of those rather than adjusting the burner yourself. If the furnace lights and shuts off after a few seconds, a dirty flame sensor is a frequent cause. Cleaning it means shutting off power and gas-side access, so hire a pro if you aren't comfortable doing that.

A rotten-egg gas smell is a different matter. Leave the house and call your gas utility or 911 from outside.

While you're at it, replace thermostat batteries, set a heating schedule, and swap humidifier pads if you have a whole-house humidifier. On high-efficiency models, glance at the condensate drain line for kinks or dripping.

Heat pump air feels cooler than furnace air, often somewhere in the 90s at the vent. That's normal, not a failure. Do find your thermostat's emergency heat setting now, and use it only if the outdoor unit stops working.

December Checklist: Safety Checks and Winter Settings

In December, test every carbon monoxide detector and smoke alarm, recheck the filter, and settle your winter thermostat habits. Testing each carbon monoxide detector takes a few minutes: press the test button, replace batteries as needed, and find the replacement date on the label. Many units last roughly 5 to 10 years. You want one on every level and near sleeping areas.

After snowstorms, clear snow from furnace vent terminations and from around the heat pump. Steam rising from a heat pump during defrost is normal. Ice that builds up and doesn't clear within a cycle or two calls for service.

On thermostats, the U.S. Department of Energy has long advised that setting back 7 to 10 degrees for about eight hours a day can cut heating and cooling costs by as much as 10 percent a year. That works well for furnaces. With heat pumps, keep setbacks to a couple of degrees, or use a smart thermostat built for heat pumps, since a big morning recovery can trigger expensive backup heat. More tips live at Energy Saver.

How Do Cold-Climate and Warm-Climate Checklists Differ?

Cold-climate homes need furnace combustion and airflow checks done early, while warm-climate homes can shift the work later and focus on the heat pump.

TaskCold climate (furnace-heavy)Warm climate (heat pump-heavy)
Tune-up timingEarly to mid OctoberLate October to mid November
Filter changesCheck monthly all winterCheck every 1 to 3 months; the system runs year-round
Outdoor unitClear before first freeze; keep snow offClear debris; rinse coil after cooling season
Safety focusFurnace venting, carbon monoxideHeat strip burn-off smell, carbon monoxide if gas appliances
ThermostatLarger setbacks are fineSmall setbacks only

Local code and climate matter here. Permit rules for equipment replacement, and who may do gas or refrigerant work, vary by locality, so ask your licensed contractor what applies to you.

What Heat Pump Maintenance Do Mild Climates Still Need?

A heat pump in a mild climate still needs a clean filter, a clear outdoor condenser, a clear condensate drain line, and a heating-mode test before the first cool night. Skipping heat pump maintenance is common in warm regions because winters seem easy. But the system has been cooling for months, collecting dirt and debris, and switching to heat engages parts that have sat idle.

Run it in heating mode in November. Confirm warm air at the vents, the outdoor fan spinning, and no odd noises. If it fails to switch modes, the reversing valve may be the culprit, and refrigerant work belongs to a licensed technician. If the house struggles on 40-degree nights even with a working unit, sizing may be the issue. Ask a contractor for a load calculation rather than guessing.

If you have electric backup strips, expect a short burning smell when they first run. It should fade quickly. If it doesn't, shut the system off and call a pro.

What Mistakes Shorten Winter System Life?

The biggest mistakes are skipping filter changes, calling for service only after the heat quits, and blocking airflow. Others are quieter:

  • Running one filter all winter, when the furnace works far harder in January than in October.
  • Wrapping a heat pump in a tight cover. It needs airflow year-round, and covers trap moisture and invite pests.
  • Using a pressure washer on condenser fins, which bends them and cuts airflow.
  • Storing boxes or paint near the furnace.
  • Ignoring a new noise or smell because the house is still warm.

Next step: call a local HVAC company today, ask for a tune-up slot before Thanksgiving, and put a monthly filter check on your phone calendar.

Questions people ask

Can I do a furnace tune-up myself?

You can handle the filter, vents, thermostat batteries, and exterior pipe checks. Combustion testing, heat exchanger inspection, and gas or electrical adjustments need a licensed technician with the right instruments. Skipping them can leave a carbon monoxide risk unnoticed.

Should I cover my outdoor unit for winter?

Not tightly, and never a heat pump, since it runs in winter and needs airflow. If you have an air conditioner only, use a cover made for it, or a breathable top cover with the sides left open so moisture escapes and animals don't nest inside.

How long does a furnace tune-up take?

Often about an hour, though a thorough visit on a larger or more complex system can run longer. Make sure someone can give the technician access to the furnace, the thermostat, and the outdoor unit.

Does a new furnace still need annual service?

Yes. A new system is less likely to fail, but dust, loose connections, and clogged drains show up on equipment of any age. Some manufacturers also ask for proof of maintenance to keep a full warranty, so check your paperwork.

What should I check if my furnace won't turn on?

Confirm the thermostat is set to heat with fresh batteries, the breaker and the furnace's service switch are on, and the filter isn't badly clogged. If it still won't start, call a technician. Don't open gas or electrical components yourself.

Sources and further reading

Elsewhere in Heating, Air & Water