Part of our Heating and Cooling guide
Furnace Repair Cost in 2026: Prices, Factors, and When to Replace
Line-item prices for five common repairs, what a service call bundles, and the age-and-quote math for deciding to replace.
Save to PinterestWe may earn a commission when you buy through links on this page. It never changes what we recommend. Learn more
The short answer
Most furnace repairs cost $100 to $450 for an igniter or flame sensor and $300 to $1,500 for a control board or blower motor. A heat exchanger runs $1,500 to $4,000 or more. Consider replacing when a quote tops roughly 50% of a new furnace, or price a replacement first if the furnace is over 15 years old and the quote tops $1,000.
- Typical cost
- $100 to $1,500 for most repairs; $1,500 to $4,000+ for a heat exchanger
- Time needed
- 1 to 3 hours for most repairs, longer if a part must be ordered
- Skill level
- Hire a pro
Key points
- An igniter or flame sensor repair usually lands between $100 and $450 installed, while a blower motor or control board runs $300 to $1,500.
- The diagnostic fee ($75 to $200) and trip charge are separate line items on many invoices, so ask whether they're credited toward the repair.
- Repair a furnace under about 12 years old if the quote is under $1,000, and price a replacement before approving anything larger on a furnace past 15.
- A cracked heat exchanger usually points to replacement, because the repair can approach half the price of a new unit and the safety risk is real.
- Cleaning a flame sensor is a reasonable DIY job; gas valves, control boards, and heat exchangers belong to a licensed technician.
In this guide
- What Does a Furnace Repair Cost in 2026?
- Repair Prices by Part: What You Pay for Parts and Labor
- What Pushes a Furnace Repair Quote Up or Down?
- How Does the 50% Rule Work, and Where Does It Break Down?
- When Does Replacing Make Sense Even With a Cheap Fix?
- What Does a Service Call Bundle, and How Do You Compare Quotes?
- How Can You Lower the Bill Without Risking Safety?
- DIY Versus Hiring Out: Where Is the Line?
Most furnace repairs run $100 to $1,500, and the part is rarely the biggest line on the invoice. A $30 flame sensor can turn into a $250 bill once the diagnostic fee, trip charge, and labor are added.
What Does a Furnace Repair Cost in 2026?
Most repairs on a standard gas furnace land between $100 and $1,500: $100 to $450 for an igniter or flame sensor, $300 to $1,500 for a control board or blower motor, and $1,500 to $4,000 or more for a heat exchanger. Your local labor rate, the brand, and how hard the furnace is to reach will move the number.
Our recommendation for the most common situation: if the furnace is under about 12 years old and the quote is under $1,000, repair it. Past 15 years with a quote over $1,000, get a replacement price in hand before you say yes. In between, use the 50% rule below.
Repair Prices by Part: What You Pay for Parts and Labor
Labor usually costs as much as the part or more, and the table splits the two for five common repairs on a standard gas furnace.
| Repair | Part | Labor | Typical installed total |
|---|---|---|---|
| Hot surface igniter | $25 to $100 | $100 to $300 | $150 to $450 |
| Flame sensor (replace) | $10 to $40 | $75 to $250 | $100 to $300 |
| Blower motor | $150 to $1,000 | $200 to $500 | $400 to $1,500 |
| Control board | $150 to $600 | $150 to $400 | $300 to $1,000 |
| Heat exchanger | $500 to $2,000 | $800 to $1,500+ | $1,500 to $4,000+ |
A hot surface igniter is a fragile, inexpensive part, so the bill is mostly labor and the service call. A tech can often swap it in under an hour. A flame sensor works the same way, and a cleaning ($75 to $200) frequently fixes the problem without a new part. Our guide on cleaning a flame sensor and confirming the cause shows how to tell which one you need.
Blower motor cost depends mostly on motor type. A standard PSC motor sits at the low end. A variable-speed blower motor with an ECM motor can cost considerably more, and some units need a separate control module on top.
Control boards get replaced, not repaired, and boards for high-efficiency furnaces cost more. One that fails repeatedly can point to something else, such as a power problem or a failing motor.
A heat exchanger replacement starts around $1,500 and can pass $4,000. Many carry long parts warranties, but the warranty usually covers the part and not the labor. Check your paperwork before you assume anything.
What Pushes a Furnace Repair Quote Up or Down?
Furnace age, equipment type, access, and timing are the main things that move a quote. Older furnaces often need parts that are discontinued or back-ordered, which means a pricey substitute or an adapter kit.
- Efficiency and staging: variable-speed and two-stage furnaces use costlier motors and boards than single-stage units.
- Location: a furnace in a tight attic or crawl space adds labor time.
- Timing: nights, weekends, and holidays often carry a premium, and a cold snap fills every tech's schedule.
- Region: big-metro and coastal labor rates run well above rural ones.
- Warranty status: a furnace still under a parts warranty can cut the bill sharply, though labor is usually on you.
How Does the 50% Rule Work, and Where Does It Break Down?
The 50% rule says to replace the furnace when a repair costs more than half the price of a new one, and it works best on furnaces past roughly 15 years old. Gas furnaces commonly last 15 to 20 years, so age tells you how much life you're buying with the repair. The table assumes a $6,000 replacement price as an example. Swap in your own quote.
| Furnace age | Repair quote | Share of $6,000 | Call |
|---|---|---|---|
| 7 years | $1,100 blower motor | About 18% | Repair |
| 14 years | $800 control board | About 13% | Repair, then budget for replacement soon |
| 16 years | $2,800 heat exchanger | About 47% | Replace |
| 19 years | $1,200 blower motor | 20% | Lean toward replacing |
The rule breaks down in both directions. A 19-year-old furnace with a $1,200 repair is well under 50%, yet you'd be pouring money into a unit near the end of its life. A 9-year-old furnace with a $2,900 quote is also under half of a new one, but a heat exchanger failing that early deserves a warranty claim and a second opinion before you spend anything.
When Does Replacing Make Sense Even With a Cheap Fix?
Replace, or at least price a replacement, when the furnace has a cracked heat exchanger, needs a second major repair within about two years, or is well past 20 years old. A cracked heat exchanger can let combustion gases, including carbon monoxide, into your living space, so don't patch around it.
Other reasons to move up the timeline:
- An older 80% efficiency furnace uses noticeably more fuel than a modern high-efficiency unit. The Department of Energy's Energy Saver site explains what efficiency ratings mean for your heating bill.
- Parts are discontinued, so every repair is a special order.
- The furnace short-cycles or heats unevenly, which can mean it was oversized from day one.
If you do replace, check ENERGY STAR for current efficiency criteria. Utility rebates and tax incentives change every year, so see what's available before you sign. A replacement also typically needs a permit and inspection for the gas and venting work. Your installer usually pulls it, but your local building department sets the rules.
What Does a Service Call Bundle, and How Do You Compare Quotes?
A service call usually bundles a diagnostic fee of $75 to $200, sometimes a separate trip charge of $50 to $150, then labor and parts. Some companies fold the trip charge into the diagnostic fee, and many credit the fee toward the repair if you approve the work. Others don't, so ask.
Parts are typically marked up over retail, which is how many shops cover the warranty and truck stock. Labor may be flat-rate (a set price per task) or hourly, and the two can produce very different totals for the same job.
A second diagnostic fee is worth paying only on bigger quotes, roughly $800 and up. Below that, the extra fee eats most of the savings.
How Can You Lower the Bill Without Risking Safety?
The most reliable savings come from scheduling, maintenance, and paperwork rather than from skipping steps.
- Call during business hours. If the furnace limps along safely, waiting until morning avoids the after-hours premium.
- Service it before winter. Our fall HVAC maintenance checklist covers the filter, sensor, and venting checks that head off many service calls.
- Look up your warranty. Check the manufacturer's parts coverage and any home warranty plan before you pay.
- Consider a maintenance plan. These often run $150 to $400 a year and may include discounted repairs or waived diagnostic fees. Read the exclusions first.
- Skip the customer-supplied part. Many shops won't warranty a part you bought, and the savings are often small.
DIY Versus Hiring Out: Where Is the Line?
Cleaning a flame sensor and changing the filter are reasonable DIY jobs, and anything involving gas, line-voltage wiring, or combustion safety belongs to a licensed technician. An igniter swap sits in between. It's within reach for a handy person with the power off, but the part cracks if you touch it with bare fingers or bump it during install.
A blower motor swap is a job for a technician unless you're experienced with electrical work, since a wrong capacitor or wiring mistake can destroy the new motor and capacitors can hold a charge. A control board looks easy, yet a miswired one can cause unsafe operation. Some manufacturer warranties also require a licensed installer, so confirm that before you open anything. Heat exchanger work is strictly professional.
Next step: write down your furnace's model number, serial number, and install year from the data plate, then call two companies and ask each for a line-item quote with its warranty terms. If the furnace isn't running at all, start with our guide on what to check before calling a tech so you don't pay a diagnostic fee for a tripped breaker.
Questions people ask
Is $500 too much to repair a furnace?
No. A $500 repair is normal for a control board or a basic blower motor and is usually worth doing on a furnace under about 15 years old. On a furnace past 18 or 20 years, treat it as a cue to price a replacement alongside.
Do I still pay the diagnostic fee if I decline the repair?
Usually yes, since the tech has already spent the time diagnosing. The fee is often credited toward the repair if you go ahead with the same company. Ask before the visit, not after.
Does homeowners insurance cover furnace repairs?
Standard homeowners policies generally don't cover wear-and-tear failures like a worn blower motor or a dead igniter. They may cover damage from a covered event such as a fire or a lightning strike. A home warranty plan is a separate product with its own exclusions and service fees.
Do furnace repairs need a permit?
Swapping a part like an igniter or flame sensor typically doesn't, but requirements vary by city and county. Replacing the furnace, or doing work on gas lines or venting, commonly does. Ask your local building department or your installer.
How long does a furnace repair take?
Most igniter, flame sensor, and board repairs take one to three hours if the tech has the part on the truck. A blower motor or an unusual board may need to be ordered, which can stretch the job to a day or two.
Sources and further reading
- U.S. Dept. of Energy, Energy Saver DOE guidance on furnace efficiency and heating costs
- ENERGY STAR Efficiency criteria and incentive information for replacement equipment
- EPA Indoor Air Quality EPA indoor air quality resources, including combustion gases and carbon monoxide
Was this article helpful?