Fix and Furrow
Advertise

Part of our Heating and Cooling guide

Heat Tape or Pipe Insulation: What Keeps Pipes From Freezing

Insulation slows heat loss; heat cable adds heat. Which one you need depends on where the pipe runs and how cold that spot gets.

Save to Pinterest

We may earn a commission when you buy through links on this page. It never changes what we recommend. Learn more

Rusty metal pipes covered in frost and ice against a brick wall
Photo: LUCAS HAN on Unsplash

The short answer

Insulate every exposed pipe with foam first. Add self-regulating heat cable under the insulation only where pipes face sustained hard cold, such as an unheated garage or an exposed crawl space that regularly drops below about 20°F. Insulation alone only delays freezing because it adds no heat. Pipes inside exterior walls are a fix-the-wall problem.

Typical cost
Roughly $0.50 to $2 per foot for foam insulation; about $2 to $6 per foot for heat cable kits
Time needed
One to three hours for a typical run
Skill level
Beginner

Key points

  • Pipe insulation delays freezing but adds no heat, so it fails in long, hard cold snaps.
  • Self-regulating heat cable is the more forgiving choice for most homeowners than constant-wattage cable.
  • Vulnerable pipes in garages and crawl spaces are best protected by insulation plus a plug-in heat cable kit with a built-in thermostat.
  • Pipes in exterior walls are usually a fix-the-wall problem, not a buy-a-cable problem.
  • Heat cable needs a GFCI-protected outlet and no extension cords, and the power may be out during the storm that freezes your pipes.
In this guide
  1. Why do pipes freeze in a crawl space, garage, or exterior wall?
  2. What does pipe insulation do, and where does it fail?
  3. Which heat cable is better: self-regulating or constant-wattage?
  4. Which should you choose for a crawl space, garage, or exterior wall?
  5. How much do pipe insulation and heat cable actually cost?
  6. What are the safe installation rules for heat cable?
  7. When are neither of these enough?

Insulation slows heat loss; heat cable adds heat. That one distinction decides nearly everything. A pipe in a sheltered crawl space that dips to 25°F for a few hours needs a delay. A supply line in an unheated garage that sits near 10°F for two nights needs actual heat. Pick the wrong one and you either overspend or end up with a split pipe in January.

Why do pipes freeze in a crawl space, garage, or exterior wall?

Pipes freeze where cold air reaches them and nothing replaces the heat the water loses. Air temperatures that stay at or below roughly 20°F put exposed pipes at risk, and wind hitting the pipe shortens the time it takes.

In a crawl space, the trouble spots are pipes near foundation vents, along the rim joist, and under floors with no insulation between the pipe and the cold air below. In a garage, it's usually a supply line along an exterior wall or across the ceiling near the door, where gaps let in outside air. Exterior walls are different. Insulation often sits between the pipe and the warm room, so the pipe ends up on the cold side with no house heat reaching it.

If the crawl space is the culprit, sealing vents and insulating the rim area helps every pipe at once. That's a bigger project than wrapping pipes, and it's worth pricing out crawl space insulation before you spend on cable for a long run.

What does pipe insulation do, and where does it fail?

Pipe insulation slows heat loss from the water but never adds any, so it only delays freezing. That's enough for short, moderate cold snaps and not enough for days of sustained cold.

You'll find three common types. The cheapest and easiest to fit is foam pipe insulation, a split polyethylene tube you slip over the pipe. Denser and thicker, elastomeric pipe insulation handles elbows and valves better. Fiberglass pipe wrap works, but it loses most of its value once it gets damp. Sleeves typically land somewhere around R-1 to R-4 depending on material and thickness, which is small next to the R-13 or more in a typical wall cavity. That's why a thin sleeve alone won't save a pipe in a drafty garage.

Failures are predictable: unsealed seams, gaps at elbows and valves, loose ends, and sleeves crushed behind stored items. Tape every seam and cover every fitting. A pipe that's 90 percent wrapped will freeze at the other 10 percent.

One caution for older homes. Aged, flaky wrap on pipes may contain asbestos. Don't cut, tear, or sweep it up; have it tested by a qualified professional before you touch it.

Which heat cable is better: self-regulating or constant-wattage?

Self-regulating heat cable is the better choice for nearly all homeowners; constant-wattage cable is cheaper but less forgiving. Self-regulating cable changes its output along its length as the surrounding temperature changes, so it draws less power where the pipe is already warm. Some models can cross over themselves without overheating, but check the instructions for yours.

Constant-wattage cable puts out the same heat everywhere. It needs an external pipe thermostat, often set to switch on somewhere around 35°F to 40°F, and it can overheat if it overlaps or sits under insulation it isn't rated for. It suits long straight runs. It punishes sloppy installation.

Product typeNeeds power?Typical costBest forWeak spot
Foam sleeveNo$0.50 to $2 per footSheltered crawl spaces, mild climatesOnly delays freezing
Elastomeric sleeveNo$1.50 to $5 per footCold crawl spaces, fittings, outdoor-adjacent runsNo heat input
Fiberglass wrapNo$1 to $3 per footDry basements and crawl spacesPoor when wet
Self-regulating heat cableYes$2 to $6 per footGarages, exposed crawl space runs, short problem spotsHigher cost; needs an outlet
Constant-wattage cableYes, plus thermostat$1 to $3 per foot, plus $15 to $40 for a thermostatLong straight runs on a budgetOverheats if overlapped or misused

Features worth paying for, and ones that aren't

Pay for a third-party safety listing such as UL or ETL, a clear rating for your pipe material, a built-in thermostat in the plug, and an indicator light that shows it's powered. Metal, PEX, CPVC, and PVC aren't all treated alike. Length matters too, since many cables can't be cut in the field.

Skip the highest wattage per foot and any extreme low-temperature rating unless you actually live where it applies. More watts doesn't mean better protection. It means more electricity and more heat on a plastic pipe.

Which should you choose for a crawl space, garage, or exterior wall?

For most crawl spaces and garages, insulate every exposed pipe and add self-regulating heat cable only on the one or two runs that see the hardest cold. That's what we'd pick for the common case of a region with occasional hard freezes. Cable on every pipe adds cost and electrical load without much benefit.

Crawl space. If it's closed, lightly vented, and rarely drops below the mid-20s, insulation alone is usually the right call. If vents are open to the weather or the space regularly falls below 20°F, add cable on the exposed runs.

Garage. Unheated garages get the coldest, so insulation plus cable is the sensible default for any supply line. Seal gaps around the door and pipe penetrations first. It's the cheapest fix there is.

Exterior wall. Don't bury cable behind drywall. Fix the wall instead: insulation belongs between the pipe and the cold exterior, and sometimes the pipe needs to move. If the wall is closed and you can't see the pipe, that's a job for a plumber or an insulation contractor.

How much do pipe insulation and heat cable actually cost?

Foam insulation for a typical 30 to 50 feet of pipe often runs $15 to $100, while a plug-in heat cable kit usually adds $50 to $200 depending on length and features. Electrical work and plumbing labor are what push totals higher.

TierWhat you getTypical total
BasicFoam sleeves, tape, and sealing gaps$15 to $100 DIY
MidInsulation plus a self-regulating heat cable kit on one or two problem runs$75 to $250 DIY
HighInsulation and cable plus an electrician-added outlet, or a plumber rerouting a pipeOften several hundred to $1,500 or more

Ranges vary with pipe length, access, local labor rates, and whether new wiring is needed. They're typical U.S. figures, not quotes.

What are the safe installation rules for heat cable?

Follow the manufacturer's instructions to the letter, plug the cable into a GFCI-protected outlet, and never use an extension cord or power strip. Most heat cable fires and failures trace back to skipping one of these steps.

  1. Confirm the cable is rated for your pipe material. Some aren't for plastic pipe.
  2. Plug into a GFCI outlet, or use a cable with a ground-fault plug. If there's no GFCI outlet near the pipe, have a licensed electrician add one. Local code may require a permit for that work.
  3. Never overlap constant-wattage cable. With self-regulating types, follow the instructions on crossing.
  4. Cover the cable only with insulation the manufacturer approves, and keep it dry.
  5. Secure the cable to the pipe at the spacing the instructions give, not in random wraps.
  6. If your kit uses a pipe thermostat, mount the sensor on the pipe, away from direct contact with the cable.
  7. Test it at the start of each season. If the indicator doesn't light or the plug feels hot, stop using it.

One caveat gets ignored: heat cable needs power, and the storm that freezes your pipes may also knock out the electricity. For a pipe that can't be allowed to freeze, insulation is your backup.

When are neither of these enough?

Neither is enough when a pipe keeps freezing despite both, when it runs inside a closed wall or under a slab, or when you can't safely get power to it. Those cases call for a plumber, an insulation contractor, or both.

Call a pro if you've already had a burst pipe, if the pipe sits in an exterior wall with no access, if a cable would need new wiring, or if the pipe is old galvanized or something you can't identify. A plumber can reroute a vulnerable line to the warm side of the house, which is permanent and needs no power. Local code affects where cable can go and which electrical or plumbing work needs a permit.

Your next step: this week, check your most exposed pipe for gaps and wrap it. Then decide whether it gets cold enough where you live to justify a heat cable kit.

Questions people ask

Can you put heat tape over pipe insulation?

Most manufacturers say to attach the cable directly to the pipe, then cover both with insulation they approve. Cable laid on top of insulation wastes heat and can overheat. Check your cable's instructions for the exact method.

Does heat cable cost a lot to run?

Self-regulating cable draws less power as the pipe warms, so it generally costs less than heating a whole space. Actual cost depends on cable length, how often it cycles, and your electricity rate. A thermostat keeps it from running when it isn't needed.

Can I use heat tape on PEX or PVC pipe?

Only if the cable is rated for it. Some are made for metal pipe only, and too much heat can damage plastic. Read the packaging and the pipe manufacturer's guidance before you buy.

Is heat tape a fire risk?

It can be if it's old, damaged, overlapped when it shouldn't be, or covered with the wrong insulation. Listed products installed per instructions on a GFCI-protected circuit are far safer. Replace any cable that looks worn.

Should I let faucets drip instead?

A slow drip on a vulnerable line can help during a hard freeze because moving water is harder to freeze. It wastes water and doesn't reliably prevent bursts. Treat it as a stopgap during a cold snap, not a plan.

Sources and further reading

Elsewhere in Heating, Air & Water