Fix and Furrow
Advertise

How to Regrout Shower Tile Without Redoing the Whole Wall

Most failing shower grout is a surface job. Here's how to dig it out, replace it, and cure it so the first shower doesn't ruin it.

Save to Pinterest

We may earn a commission when you buy through links on this page. It never changes what we recommend. Learn more

Close-up of white shower wall tile with fresh grout lines and a caulked corner
Photo: Mick Haupt on Unsplash

The short answer

To regrout shower tile without tearing out the wall, cut the old grout out to roughly 1/8 to 1/4 inch deep with a narrow carbide blade, pack in polymer-modified cement grout, wipe off haze 15 to 30 minutes later, and seal once it cures. Recaulk corners and the tub line with silicone instead of grouting them. Keep the shower dry for about 72 hours.

Typical cost
$40 to $150 in materials; pros often charge $300 to $1,000 depending on size and region
Time needed
One weekend, plus about a 72-hour cure before showering
Skill level
Intermediate

Key points

  • Grout the flat joints between tiles, but use flexible silicone caulk at inside corners, the tub line, and the floor joint.
  • Use a carbide blade narrower than the joint and cut roughly 1/8 to 1/4 inch deep to remove old grout without chipping glazed tile edges.
  • Polymer-modified cement grout, sealed after curing, is the best choice for most DIY shower wall regrouting; epoxy is tougher but harder to work.
  • Wipe haze within 15 to 30 minutes, and keep water off cement grout for about 72 hours, or whatever the label says.
  • Loose or hollow tiles, a soft wall, or water stains nearby mean water is behind the tile and it's time for a pro.
In this guide
  1. Regrout or Recaulk? How to Tell Before You Start
  2. Tools and Materials You Need
  3. Prep the Shower So Grout Cures Properly
  4. Remove the Old Grout Without Chipping Tile
  5. Mix and Apply the New Grout
  6. How Do You Clean Grout Haze and Tool the Joints?
  7. How Long Before You Can Use the Shower After Regrouting?
  8. When to Stop and Call a Tile Pro

Grout that is stained, crumbling in spots, or cracked at the corners is rarely a reason to pull tile. If the tiles are tight and the wall is solid, you can cut out the old joints, repack them, and recaulk the corners in a weekend, with a few days of curing built in.

Regrout or Recaulk? How to Tell Before You Start

Regrout the flat joints between tiles, and recaulk anywhere two surfaces meet: inside corners, the line where the wall meets the tub or shower pan, and the joint at the floor. Those spots move as the house settles and as materials expand and shrink with hot water. Rigid grout can't flex, so it cracks there no matter how well you install it. Flexible caulk can.

A crack running along a corner or the tub line is a caulk job. A crack or crumble in a joint between two tiles on the flat wall is a grout job. A hairline crack straight down a vertical corner usually means someone grouted a movement joint, and it will fail again if you repeat the mistake. Most bathrooms need both fixes.

Before you commit, probe. Press a screwdriver tip into several joints and tap tiles with the handle. A few hollow sounds near edges are common. A whole patch of loose, hollow tiles, or a wall that feels soft near the tub, means water has already gotten behind the tile. Regrouting would only hide that, so skip to the last section.

Tools and Materials You Need

You need a grout removal tool, a grout float, a respirator, grout, sealer for cement grout, and silicone caulk, which usually adds up to $40 to $150 in materials plus an oscillating tool if you don't own one.

  • An oscillating multi-tool with a carbide grit grout blade, or a carbide grout saw for hand work (slower, but easier to control near glazed edges)
  • Utility knife and a plastic scraper or caulk removal tool
  • Shop vacuum
  • N95 or better respirator, safety glasses, and gloves
  • Painter's tape and a drop cloth
  • Mildew cleaner or oxygen bleach, and a stiff nylon brush
  • Grout, a clean bucket, and a mixing paddle or margin trowel
  • Rubber grout float, two large sponges, and microfiber cloths
  • Penetrating grout sealer (for cement grout)
  • 100% silicone caulk labeled for kitchen and bath, rubbing alcohol, and a caulk gun

Which grout is best for shower walls?

For most DIY work on shower walls, polymer-modified cement grout is the best pick, because it forgives mistakes and costs far less than epoxy. Joint width picks the type: unsanded grout suits joints about 1/8 inch or narrower, which covers most wall tile, while sanded grout is for wider joints. Check the bag for its stated range.

FactorCement groutEpoxy grout
Ease of useForgiving, easy to cleanSticky, unforgiving
Working timeLongerShorter, so mix small batches
Stain and mold resistanceGood when sealedVery good, no sealer needed
CostLowNoticeably higher
Best forMost DIY shower wallsSmall areas, constantly wet walls, light colors that stain

The choice comes down to patience. Pick epoxy if you can work fast and want less maintenance. Vacuum the joints thoroughly first, and know that cured epoxy is miserable to cut out later.

Buy a small sample for color. Old grout darkens with age, and new grout dries a shade different from the wet mix, so regrout the whole wall plane rather than a few patches.

Prep the Shower So Grout Cures Properly

Clean the wall, let it dry, and mask what you don't want grouted before you touch a blade. Scrub the tile and joints with mildew cleaner or oxygen bleach and a nylon brush, then rinse well. Never mix bleach with ammonia or acidic cleaners, which can release toxic gas.

Run the exhaust fan and let the wall dry for about 24 hours. Grout won't bond well to wet, soapy joints, and epoxy is especially fussy. Lay tape along the tub rim, put a drop cloth in the tub, and plug the drain with a rag so chips and dust don't go down it.

Remove the Old Grout Without Chipping Tile

To remove old grout from shower tile without chipping it, use a blade narrower than the joint, keep it centered, and cut roughly 1/8 to 1/4 inch deep, never through to the backer.

  1. Cut the caulk first. Slice along both edges of the old caulk at corners and the tub line, peel it out, and scrape off residue. Leftover silicone stops new caulk from sticking.
  2. Match the blade to the joint. A blade wider than the joint bites the glazed edge, which is where chips start. For very thin joints, use a carbide grout saw by hand.
  3. Cut at low to medium speed. Rest the blade in the middle of the joint, keep it in line, and use light pressure. Don't rock it sideways.
  4. Finish the intersections by hand. Stop short of where joints cross and clear those spots with the hand saw so the power tool never swings into a corner.
  5. Vacuum and wipe. Remove every bit of dust, then go over the joints with a damp sponge. Solid grout at the bottom of the joint can stay. Anything loose has to go.

Mix and Apply the New Grout

Mix only what you can use within the label's working time, often about 30 minutes for cement grout, and pack the joints diagonally with the grout float in small sections of about 10 square feet or less.

  1. Mix to the label. Most brands want the powder added gradually to the measured liquid. Let it rest 5 to 10 minutes if the label says so, then remix. The right texture is thick peanut butter that holds a ridge. Soupy grout shrinks and weakens.
  2. Dampen the joints. For cement grout, wipe the wall with a barely damp sponge. Skip this for epoxy unless the label says otherwise.
  3. Pack the joints. Start at the top of the section. Hold the float at roughly 45 degrees and push grout in diagonally across the joints so the edge doesn't dig out the fill. Go over each joint twice.
  4. Scrape the excess. Tilt the float near 90 degrees and drag it diagonally across the tile to take off surface grout.
  5. Wait. Give cement grout 15 to 30 minutes, until it feels firm but not hard.

Epoxy runs on a shorter clock. Mix smaller batches and follow the manufacturer's working time exactly.

How Do You Clean Grout Haze and Tool the Joints?

Wipe the wall with a barely damp sponge once the grout is firm, usually after 15 to 30 minutes, then buff leftover haze with a dry microfiber cloth a few hours later. Wring the sponge out hard and rinse it often in clean water. Too much water pulls grout out of the joints and blotches the color.

Use light, diagonal strokes, and let the sponge shape each joint into a slight concave curve. Corners and edges dry faster, so check them first.

If haze survives after the wall has dried, a grout haze remover made for cement grout works, but follow the label on timing, since many ask you to wait several days. Don't use vinegar or acid on cement grout, and keep acids off natural stone like marble. Epoxy haze has to come off while the epoxy is fresh, because cured epoxy film is stubborn.

How Long Before You Can Use the Shower After Regrouting?

Stay out of the shower about 72 hours after regrouting with cement grout, and often a day or two with epoxy, but the label on your grout is the final word. Rushing it is the most common reason fresh grout washes out.

Seal cement grout after it cures, usually 48 to 72 hours. Brush on penetrating grout sealer along the joints, wipe it off the tile face within a few minutes, and add a second coat if the label says so. Keep sealer out of the corner and tub joints, since silicone won't stick to it. Epoxy doesn't need sealer.

Recaulk once the grout has cured. Fill the tub with water first, so the tub sits at its loaded position and the caulk doesn't pull apart when you step in. Tape both sides of the gap, run a steady bead of 100% silicone caulk, smooth it with a gloved finger dipped in rubbing alcohol, and pull the tape before it skins over. Leave it for the cure time on the tube, often 24 hours, before water touches it.

For the first shower, keep it short and lukewarm, run the fan, and squeegee the wall afterward. Skip abrasive scrubbing for a week.

When to Stop and Call a Tile Pro

Call a tile pro if tiles are loose or hollow in a patch, the wall feels soft, or you see water damage anywhere around the shower. Those signs point to a failed waterproofing layer, not tired grout.

  • Several adjacent tiles move or sound hollow when tapped
  • Black mold, stains, or soft drywall on the other side of the wall or on the ceiling below
  • Grout cracking again across large areas, which suggests flex in the wall
  • Natural stone tile, which etches and stains easily
  • Cracked tiles, or a surround that has been regrouted several times already
  • Old backer, mastic, or paint you suspect contains asbestos or lead, which needs testing before anyone disturbs it

Regrouting alone rarely needs a permit. Opening the wall to repair rot or redo waterproofing may, and the rules vary by city, so ask your local building department before work starts.

A pro regrout of a standard shower typically runs $300 to $1,000, depending on size, grout type, and region. If you hire out, the FTC's consumer advice site has general guidance on vetting contractors and reading estimates.

Your next step: regrout one low, out-of-sight 2-foot-square section first. If it goes well, do the rest of the wall the same day.

Questions people ask

Can I regrout over the old grout?

Not reliably. New grout needs depth to grip, and a thin layer over old grout tends to crack and flake off. Cut the old grout out first.

Can I change the color of my grout instead of regrouting?

Grout colorants and stains can fix discoloration on joints that are sound. They don't repair cracks, gaps, or crumbling, so use them only when the grout itself is still solid.

Why does shower grout keep turning dark?

Dark spots are usually mold or mildew growing on soap film, and unsealed cement grout also absorbs stains. Poor ventilation makes it worse. Running the fan after showers and squeegeeing the wall slow it down.

How long should regrouted shower tile last?

Well-installed and sealed cement grout can last many years, and epoxy often lasts longer. Ventilation, sealing, and how well the caulked joints hold up all change that.

Do I need to kill mold before regrouting?

Clean the surface with a mildew cleaner or oxygen bleach first. Cutting out the old grout removes most of what's growing in the joint. If mold shows up behind the grout or on the backer, stop and have the wall checked.

Sources and further reading

Elsewhere in Remodeling