Part of our Home Repair Troubleshooting guide
Solar Inverter Ground Fault: Causes, Safe Checks, Next Steps
Most faults trace to chewed wire or wet connectors. Here is what you can look at from the ground and where the do-it-yourself part stops.
Save to PinterestWe may earn a commission when you buy through links on this page. It never changes what we recommend. Learn more
The short answer
A ground fault error means the inverter detected current leaking from the DC wiring to ground, or low insulation resistance, so it shut down. Common causes are chewed or chafed wire insulation and moisture in connectors. Note the code and time, restart once per the manual, look from the ground only, and call a licensed installer if the fault returns.
- Typical cost
- $0 for your own checks; often $150 to $400 for an installer diagnostic visit, plus repair costs
- Time needed
- 30 minutes for the safe checks
- Skill level
- Hire a pro
Key points
- A ground fault shutdown is a safety response, so repeated resets are a bad idea rather than a fix.
- Record the error code, the time, and the weather before you do anything else; it helps an installer narrow the cause quickly.
- Damaged DC wire insulation and moisture in connectors are common causes, and both need a professional to repair.
- Your safe checks are visual and from the ground: no opening the inverter or combiner box, no unplugging connectors, no roof walking.
- Burning smells, scorch marks, melted plastic, or a fault that returns after one restart mean leave it off and call.
In this guide
- What does a solar inverter ground fault mean?
- What should you do before touching anything?
- Cause 1: Damaged or chafed DC wire insulation
- Cause 2: Moisture in combiner boxes and MC4 connectors
- Cause 3: Loose or failed connectors and junction boxes
- Cause 4: Grounding faults in panels or racking
- Cause 5: A failing inverter or ground fault detector
- When should you call a licensed installer right away?
Write down three things before you touch the system: the exact error text or code, the date and time it appeared, and the weather over the previous 24 hours. That log is the most useful thing you can hand an installer, and it often points at the cause on its own.
What does a solar inverter ground fault mean?
A ground fault means the inverter detected electricity leaking from the DC wiring to ground, or measured insulation resistance below its safety threshold, and shut itself down to prevent shock or fire.
Rooftop strings often run at several hundred volts DC. Many string inverters test insulation before they start each day, while older designs use a ground fault detector interrupter that trips or blows a fuse when it sees leakage. The display might say "ground fault," "isolation fault," or "insulation resistance low," or show a code such as GFDI. Your manual's error table tells you which one you have. For background on how these systems are built, the DOE Solar Energy Technologies Office is a good starting point.
The causes below are ordered by what's worth checking first. Your system may differ.
| Cause | Typical pattern | What you can check | Who fixes it |
|---|---|---|---|
| Damaged wire insulation | Persistent, may worsen over weeks | Hanging cable, nesting debris, from the ground | Installer |
| Moisture in boxes or connectors | Appears after rain or dew, clears by afternoon | Weather history, water at the inverter | Installer |
| Loose or failed connector | Intermittent, may follow wind or heat | Visible damage, discoloration | Installer |
| Panel or racking fault | Persistent, sometimes after hail or roof work | Cracked glass, shifted rails | Installer |
| Failing inverter | Fault at every startup, no weather link | Age, other error codes | Installer or manufacturer |
What should you do before touching anything?
Read the error history first, restart the system once using the manufacturer's shutdown order, and keep your hands off anything with exposed wire or damaged insulation.
- Log it. Photograph the display or screenshot the monitoring app. Note whether the fault cleared on its own and what time of day it happens.
- Check the weather. Rain, heavy dew, or a windstorm in the last day points toward moisture or a loose connection. A fault on a dry, calm day points toward damaged wire or equipment.
- Restart once. Follow your manual's sequence. A common one is AC breaker off, then the DC disconnect off, a five-minute wait, then back on in reverse order. If your manual says otherwise, the manual wins. This is one test, not a routine.
- Stop if it returns. Leave the system off and call.
Resist the urge to keep resetting. Each restart can put voltage back on the very leak the inverter shut down to avoid, and some units lock out until an installer clears them.
Cause 1: Damaged or chafed DC wire insulation
Chewed, pinched, or sun-cracked DC wire insulation is a leading suspect because the cable sits exposed under the array for years.
Squirrels and rats like the warm, sheltered space under panels and will chew cable jackets. Older cable can crack from heat and UV, and any wire that sags against a metal rail edge or roof flashing can wear through. Once bare conductor touches metal, the inverter sees leakage to ground.
From the ground, with binoculars if you have them, look for cable hanging below the array, missing edge mesh, nesting debris, or chew marks on any conduit you can reach. Don't climb up for a closer look. The fix is repair of the damaged section, new cable clips, and often a rodent guard along the array edge. An installer confirms the diagnosis with an insulation resistance test, which measures leakage on each string with the system isolated. Expect roughly $200 to $1,500 for repair, depending on roof access and how much cable is damaged.
Cause 2: Moisture in combiner boxes and MC4 connectors
Water in a combiner box or in MC4 connectors causes ground faults that show up after rain or morning dew and often clear by afternoon.
Damp connectors lower insulation resistance enough to trip the check, then dry out as the sun heats the array. That on-and-off pattern fools people into thinking the problem fixed itself. It didn't. The leak is still there and corrosion keeps building.
Your safe check is external only. Look at the inverter enclosure and any outdoor box for water staining, cracked lids, or conduit entries pointing the wrong way. Don't open anything to look inside. The installer will dry and reseal the box, replace gaskets, and swap damaged connectors.
Cause 3: Loose or failed connectors and junction boxes
A loose or failed connector usually causes intermittent faults, because poor contact lets moisture in and can create heat or arcing.
Connectors are meant to be mated once and left alone. Cracked housings, half-seated plugs, and mismatched MC4-style connectors from different makers are all known trouble spots. Wind and thermal cycling make a marginal connection come and go, which is why the error may not follow the weather.
If it's reachable from the ground, look for browning, melted plastic, or a connector hanging free. Never unplug one yourself. These connectors aren't meant to be separated under load, and doing it can throw an arc. Discoloration or melting means leave the system off and call right away. Replacement takes correct crimping and matched parts, which is installer work.
Cause 4: Grounding faults in panels or racking
A grounding fault in a panel or racking happens when a damaged module or a failed bond lets DC current reach the metal frame or rails.
Hail, a dropped tool during roof work, a cracked glass face, or water getting past a damaged backsheet can all do it. On a ground mount, shifting rails or a corroded bonding point can also break the grounding path. From the ground, look for cracked glass, a panel sitting out of line, or rails that moved.
Don't touch frames or racking to test them. Fixes range from replacing one module to redoing bonding, and wiring changes may need a permit depending on your jurisdiction. Your local building department sets the rules, working from model codes published by groups like the International Code Council.
Cause 5: A failing inverter or ground fault detector
A failing inverter or ground fault detector is worth suspecting only after the wiring has been ruled out.
Suspect it when the fault comes back at every startup regardless of weather, when other error codes appear alongside it, or when the unit is more than about 10 years old. A blown fuse in a system with a detector fuse is not a cue to drop in a new one yourself. The fuse usually blew because of a real leak somewhere, and a fresh fuse can mask it.
Replacing a string inverter typically runs roughly $1,500 to $4,000 installed, depending on size and features. Check your paperwork for warranty terms first, since string inverter warranties commonly run 10 years and sometimes longer. If shade or roof layout is why you're weighing a different design, ask the installer to quote microinverters alongside a like-for-like swap.
When should you call a licensed installer right away?
Call a licensed solar installer immediately if you see burn marks, smell burning, find damaged wiring, or the fault returns after one restart.
- Scorched, melted, or discolored equipment or conduit
- Visible cable damage, a hanging wire, or a cracked panel
- Water inside the inverter or a box
- A blown ground fault fuse or a lockout that won't clear
- A fault that comes back after one proper restart
We'd start with the company that installed the system, since workmanship warranties often cover this. If they're gone, look for a NABCEP-certified installer and ask for a string-by-string insulation resistance test with written findings. Repairs to DC wiring are licensed electrical work in most places, and some need a permit and inspection, so don't hire anyone who waves that off. Be wary of unsolicited "free inspection" offers; the FTC's consumer advice pages offer guidance on solar sales pitches. A system left off loses production, but that costs far less than a fire.
Your next step: if the system faulted twice, leave it off, send the installer your log and photos, and ask for an insulation resistance test before anyone replaces parts.
Questions people ask
Can a ground fault on solar panels start a fire?
It can in rare cases, which is why inverters shut down when they detect one. Leakage to ground can heat or arc at a damaged spot. If you see scorching or smell burning, keep clear and call 911 if there is smoke or flame.
Is it okay to keep running the system if the fault clears itself?
Not indefinitely. A fault that comes and goes usually means insulation or a seal is degrading, and it tends to get worse. Schedule an inspection soon, and shut the system down if it starts faulting repeatedly.
Does my warranty cover a ground fault repair?
It depends on what failed. Equipment warranties generally cover defective parts, while the installer's workmanship warranty is what usually covers wiring and connector problems. Coverage and labor terms vary, so read both documents before paying for a repair.
Can I get shocked by a solar system with a ground fault?
Yes, it's possible. A fault can put voltage on frames, racking, or conduit that are normally safe to be near, and panels stay live in daylight. That is why homeowners should look but not touch.
Why does my inverter show a ground fault only after it rains?
Water is likely getting into a connector or combiner box and lowering insulation resistance. It clears as things dry, but the entry point stays. An installer can find and seal it before corrosion makes the problem permanent.
Sources and further reading
- DOE Solar Energy Technologies Office Federal overview of how solar electric systems work
- International Code Council Model building codes that local jurisdictions adopt
- FTC Consumer Advice Consumer guidance on avoiding solar contractor scams
Was this article helpful?