Fix and Furrow
Advertise

HRV Installation Cost in 2026: Unit, Ducts, and Labor

A tie-in to your furnace ducts and a standalone ducted system are different jobs with different bills, and climate decides HRV or ERV.

Save to Pinterest

We may earn a commission when you buy through links on this page. It never changes what we recommend. Learn more

Wall-mounted HRV unit with insulated round ducts in an unfinished basement mechanical area
Photo: Janusz Walczak on Unsplash

The short answer

Expect about $1,800 to $4,500 to tie an HRV or ERV into an existing forced-air system, and $3,500 to $8,000 for a standalone ducted install in a house without ductwork. Difficult houses can pass $10,000. The unit itself runs $800 to $3,500. Duct runs, electrical, drains, and access make up the rest.

Typical cost
$1,800 to $4,500 for a tie-in; $3,500 to $8,000 for a standalone ducted install
Time needed
One to three days for a pro crew
Skill level
Hire a pro

Key points

  • A tie-in to existing ducts often costs $1,500 to $3,500 less than a standalone ducted system.
  • On a standalone job the unit is often the smaller share; duct runs to bedrooms and attic or crawl space access drive the rest.
  • Choose an ERV in hot, humid Southern climates and an HRV in cold northern ones; the price gap is typically $100 to $500.
  • DIY on accessible duct can cut part of the labor bill, but electrical work, combustion safety checks, and airflow balancing belong with licensed pros.
  • Compare quotes by airflow in cubic feet per minute, duct material, and permit handling, not by the bottom-line number.
In this guide
  1. What does an HRV or ERV do, and why does the price vary so much?
  2. Cost table: equipment, ductwork, and labor by install type
  3. Standalone ducted install vs tie-in to an existing forced-air system
  4. What pushes the HRV installation cost up?
  5. What pushes the price down?
  6. HRV vs ERV: how climate changes the cost and the right choice
  7. DIY vs hiring out: what a homeowner can safely do and what needs a licensed pro
  8. Ways to save without shortchanging airflow or warranty

A tie-in to an existing forced-air system usually costs $1,800 to $4,500. A standalone ducted system in a house with no ductwork runs $3,500 to $8,000, and awkward houses can go past $10,000. On a standalone job the unit is often the smaller share. Duct runs, electrical, a drain, and access make up the rest. These are typical U.S. ranges, and local labor rates and your house will move them.

What does an HRV or ERV do, and why does the price vary so much?

An HRV or ERV is a ventilation unit that pulls fresh outdoor air in and pushes stale indoor air out through a heat-exchange core, so much of the energy in the outgoing air stays in the house. A heat recovery ventilator (HRV) transfers heat only. An energy recovery ventilator (ERV) moves some moisture along with the heat.

The price swings because the box is the easy part. A whole house ventilation system is really a small duct system, and every foot of duct, every wall penetration, and every hour in a hot attic is billable. That's why a 1,200-square-foot ranch with an open attic can cost less than a 2,000-square-foot two-story with finished ceilings.

For airflow targets, ASHRAE Standard 62.2 is the common residential ventilation standard, and ASHRAE publishes it. Your local code may set its own requirement.

Cost table: equipment, ductwork, and labor by install type

Most homeowners spend $1,800 to $4,500 for a tie-in and $3,500 to $8,000 for a standalone ducted install, with the unit itself at roughly $800 to $3,500 either way.

Line itemMaterialsLaborNotes
HRV or ERV unit$800 to $3,500Included belowPrice follows airflow capacity and core efficiency
Standalone ductwork (4 to 8 runs, grilles)$500 to $2,000$1,000 to $3,000Rigid or insulated flex; access sets the labor
Tie-in to forced-air system$100 to $400$500 to $1,500Short duct stubs, damper, furnace interlock
Exterior hoods and wall penetrations$50 to $250$200 to $600Siding type and wall construction matter
Condensate drain$50 to $200$100 to $400A pump adds cost if no gravity drain is nearby
Electrical (outlet or dedicated circuit)$50 to $200$150 to $500Often must be done by a licensed electrician
Controls and wall switch$75 to $300$50 to $200Humidity-sensing controls cost more
Permit and airflow balancing$50 to $400 (permit)$100 to $500Permit rules vary by city and county
Typical total: tie-in$1,800 to $4,500Existing furnace ducts in decent shape
Typical total: standalone$3,500 to $8,000No usable ductwork
Difficult house$8,000 to $12,000+Finished ceilings, multiple floors, long runs

Per square foot, a standalone system lands around $1.50 to $4, but treat that as a sanity check only. Layout and access beat square footage every time. If you only want the price of the equipment, it's the first row.

Standalone ducted install vs tie-in to an existing forced-air system

A tie-in is often $1,500 to $3,500 cheaper because it borrows the furnace's ducts, while a standalone system needs its own supply and exhaust runs.

In a tie-in, the ventilator pulls stale air from a central point or from bathrooms and delivers fresh air to the return side of the furnace, and the furnace blower spreads it through the house. The catch: the blower has to run whenever the ventilator does, which costs electricity, and the added airflow changes static pressure in the duct system. A good installer checks that the furnace still moves its rated air and wires an interlock so the two start together. A variable-speed blower usually handles this far better than an old single-speed motor.

A standalone system has its own supply runs to bedrooms and living areas and its own exhaust pickups at bathrooms and the laundry. It costs more. It also works in houses heated by boilers, electric baseboard, or ductless mini-splits, and it doesn't depend on the furnace.

Our pick for the most common situation: if you have a forced-air system with tight, sealed ducts and a variable-speed blower, tie in. If the ducts leak or run through an unconditioned attic, pay for the dedicated system. Fresh air pushed through leaky ducts wastes the money you spent on recovery.

What pushes the HRV installation cost up?

Long duct runs to bedrooms, hard-to-reach installation spots, a condensate drain with no plumbing nearby, and new electrical work are the four biggest price drivers.

Duct runs come first. Each bedroom run typically adds $200 to $700 depending on access, and a finished second floor can mean building soffits or chases, or patching drywall for $300 to $1,000 or more.

Second is the condensate drain. In cold climates an HRV can produce condensate during defrost cycles, so it needs a line to a floor drain, a laundry standpipe, or a small pump.

Third is power. Most residential units run on a standard 120-volt supply, but if there's no outlet near the unit, expect an electrician bill of $150 to $600, and more if a dedicated circuit is required.

Access is the quiet one. A unit hung in a cramped crawl space or a 110-degree attic takes longer to install, and crews price for it. Attic ducts also need to be insulated or buried, so attic insulation matters here. Our comparison of cellulose vs fiberglass attic insulation helps if you're upgrading it at the same time.

What pushes the price down?

Existing ductwork in good condition, a mechanical room near an exterior wall, and a simple layout with an open attic keep the bill at the low end of each range.

Timing can help. HVAC crews are often less booked in spring and fall than in midsummer or midwinter, so you may get quicker scheduling and sometimes a better price. Bundling helps more: adding ventilation during a furnace or heat pump replacement means the crew is already on site, and opening walls during a renovation can cut ductwork labor. If you're sizing new equipment at the same time, our guide on what size heat pump you need explains how sizing works.

Some utilities and states offer rebates for efficient ventilation equipment. Availability and amounts vary, so check before you buy. The ENERGY STAR rebate finder is a reasonable place to look for current offers.

HRV vs ERV: how climate changes the cost and the right choice

An ERV typically costs $100 to $500 more than a comparable HRV, and it's the better pick in hot, humid Southern climates, while an HRV makes more sense in cold northern ones.

The reason is moisture. In a humid summer, an ERV core keeps part of the outdoor humidity from coming inside, which lightens the load on your air conditioner. In a cold winter, an HRV lets more indoor moisture leave with the exhaust air. That helps in a tight house with lots of cooking, showers, and people, where condensation on windows is the warning sign. An ERV in the same house holds more moisture in, which suits very dry climates and works against you in damp ones.

Drains matter too. HRVs in cold regions usually need a condensate drain, while ERVs often need less drainage, so the cost gap on a quote can shrink or flip once drain work is added. In mixed climates either type works, and local installer experience is a fair tiebreaker. Neither replaces a dehumidifier in a swampy Gulf Coast summer. The U.S. Department of Energy's Energy Saver pages cover ventilation and humidity basics.

DIY vs hiring out: what a homeowner can safely do and what needs a licensed pro

A handy homeowner can often mount the unit and run accessible duct, but electrical work, combustion safety checks, and airflow balancing are best left to licensed professionals.

Doing the easy parts yourself can trim part of the labor on a standalone job. The practical split is to hang the unit, run and seal duct through open attic space, and stub out the drain line, then hire out the rest. Wiring is work for a licensed electrician in most places, and unpermitted work can cause trouble when you sell. Balancing needs a flow hood or similar tool to confirm that supply and exhaust airflows match, because an unbalanced system can pressurize or depressurize the house.

Read the warranty before you buy, too. Some manufacturers require installation by a certified contractor, and a DIY install can void coverage. Ventilation isn't a radon fix either, so if you haven't checked, see how to test for radon yourself.

Ways to save without shortchanging airflow or warranty

The safest way to save is to get three written quotes that list airflow in cubic feet per minute, duct material, and who pulls the permit, then compare scope instead of the bottom line.

  • Ask each contractor to size the unit from your house, not a rule of thumb. Oversized units cost more and run louder.
  • Keep the unit near an exterior wall to shorten the insulated intake and exhaust ducts.
  • Clear the attic path and mechanical room before the crew arrives.
  • Skip premium humidity-sensing controls if a simple timer or wall switch does the job.
  • Don't cut the balancing visit. It costs roughly $100 to $500 and protects the whole system.

Ventilation filters air only lightly, so if allergens or smoke are the issue, read how a HEPA air purifier compares with a whole house air cleaner. Your next step is simple: check where your ducts run, note which bedrooms are hardest to reach, and ask for tie-in and standalone quotes side by side.

Questions people ask

How much does an HRV or ERV cost to run each year?

Most residential units cost somewhere between tens of dollars and low hundreds of dollars a year in electricity, depending on fan speed, run hours, and local rates. A tie-in that runs the furnace blower alongside the ventilator costs more than a standalone unit, so ask your installer about blower motor type.

How long does it take to install an HRV or ERV?

A tie-in to existing ducts is often a one-day job for a two-person crew. A standalone ducted system typically takes two to three days, longer if ceilings need patching or the layout is complicated.

Do I need a permit to install an HRV or ERV?

Often, yes. Many jurisdictions require a mechanical permit for ventilation equipment and an electrical permit if a new circuit is added, but rules vary by city and county. Call your local building department before work starts, and ask your contractor who pulls the permit.

Does an HRV or ERV replace my bathroom fans?

Not always. Some systems pull exhaust from bathrooms and make a separate fan unnecessary for background ventilation, but many codes still call for a fan with higher spot-ventilation capacity for showers. Check your local code and ask the installer.

What maintenance costs should I plan for?

Plan on cleaning or replacing filters every few months and cleaning the core on the schedule in the manual, often once or twice a year. Filters usually run $10 to $50 each, and the work is a basic homeowner task if the unit is easy to reach.

Sources and further reading

Elsewhere in Heating, Air & Water