How to Shock Chlorinate a Well: Bleach Dose, Flushing, Retest
Dose by casing size, hold 12 to 24 hours, flush away from the septic, then confirm with a lab test before you drink.
Save to PinterestWe may earn a commission when you buy through links on this page. It never changes what we recommend. Learn more
The short answer
Work out the gallons of water standing in your casing (0.0408 × diameter in inches squared × feet of water), add enough unscented household bleach to reach about 200 mg/L, circulate it through every tap, and hold it 12 to 24 hours. Flush until the chlorine is gone, wait about a week, then pass a coliform test. Boil or use bottled water until then.
- Typical cost
- About $30 to $90 in supplies plus a $20 to $80 lab test; a pro visit often runs $150 to $500
- Time needed
- One working day, plus roughly 10 to 14 days until a lab result clears the water
- Skill level
- Intermediate
Key points
- Dose from your actual casing diameter and water depth, not a one-size-fits-all quart of bleach.
- Use fresh, plain, unscented household bleach and bypass any carbon filter, softener, or reverse osmosis unit first.
- Hold the chlorine in the system for 12 to 24 hours, then flush outdoors and away from the septic field and plants.
- A fading chlorine smell doesn't prove the water is safe; a passing coliform test about a week later does.
- A repeat positive, a damaged casing, or flood contamination means stop and call a licensed well contractor.
In this guide
- When Is Shock Chlorination the Right Fix?
- What Tools and Materials Do You Need?
- How Much Bleach Does Your Well Need?
- How Do You Mix, Add, and Circulate the Chlorine?
- How Do You Flush Without Dumping Chlorine Into the Yard or Septic?
- How Long Until the Water Is Safe to Drink?
- What Mistakes Make Shock Chlorination Fail?
- When Should You Call a Well Professional?
Don't pour in a quart of bleach and hope. The right dose depends on how much water is standing in your casing, and you can work that out in about five minutes with a calculator and your well log. Plan on one working day for the procedure and roughly ten to fourteen days before the water is confirmed drinkable, because the lab retest clears it, not a fading chlorine smell.
When Is Shock Chlorination the Right Fix?
Shock chlorination is the right fix for a one-time bacterial problem, such as a positive coliform result, a newly drilled well, or a pump that was just pulled for repair. Strong chlorine is meant to disinfect the casing, pump, pressure tank, and household piping in one pass.
It does nothing for nitrate, arsenic, radon, or hardness, and it won't seal a cracked casing or a loose well cap. If bacteria keep coming back after one clean shock, something is letting them in. Treat the chlorine as a reset, not a repair.
Until you have a negative result, drink bottled water or water brought to a rolling boil for one minute. The EPA's private well guidance recommends testing for coliform bacteria at least once a year, so a positive is a good reason to shock and then retest.
What Tools and Materials Do You Need?
You need fresh bleach, a garden hose, chlorine test strips, basic safety gear, and a coliform sample kit from a state-certified lab. Gather everything before you start, because you can't take breaks once the chlorine is in.
- Unscented household bleach, fresh, with 5% to 8.25% sodium hypochlorite on the label. Skip scented, splashless, or color-safe versions with additives.
- A clean 5-gallon plastic bucket, measuring cups, and a funnel.
- A garden hose long enough to reach from an outdoor hose bibb to the well.
- Chlorine test strips or a DPD test kit that reads free chlorine.
- Splash goggles, rubber gloves, and clothes you don't mind bleaching.
- A screwdriver or wrench for the well cap, plus your well log or a tape measure.
- Bottled water for drinking and cooking until your clean result comes back.
- A dechlorinating product such as sodium thiosulfate or a vitamin C neutralizer, for treating flush water.
- A coliform test kit from a state-certified lab. Call first, since labs set their own sampling days and hold times.
Supplies run roughly $30 to $90, depending on how much bleach you need. A lab coliform test typically costs $20 to $80, depending on your state and lab.
How Much Bleach Does Your Well Need?
Gallons of bleach = well gallons × 200 ÷ (bleach percent × 10,000), which gets you to about 200 mg/L, a common target for well disinfection. Some states specify different numbers, so check your health department's page.
To get well gallons, use the casing's inside diameter. Gallons per foot of water = 0.0408 × diameter in inches, squared. Your well log lists casing diameter, total depth, and static water level. Subtract the water level from the depth to get the feet of water. Without a log, measure around the outside of the casing, divide by 3.14, and subtract a little for wall thickness. State well records often list depth and casing size too.
| Casing diameter | Gallons per foot | Bleach per 100 ft of water at 200 mg/L (6% bleach) | At 100 mg/L |
|---|---|---|---|
| 4 inches | 0.65 | about 3.5 cups | about 1.7 cups |
| 5 inches | 1.02 | about 5.4 cups | about 2.7 cups |
| 6 inches | 1.47 | about 7.8 cups | about 3.9 cups |
| 8 inches | 2.61 | about 13.9 cups | about 6.9 cups |
Here's a worked example. A 6-inch casing, 150 feet deep, with water standing at 40 feet, has 110 feet of water. That's 110 × 1.47, about 162 gallons. At 200 mg/L with 6% bleach, you need 162 × 200 ÷ 60,000, or 0.54 gallon. That's roughly 8.6 cups. With 8.25% bleach, use about 6.3 cups.
The dose is based on the water in the casing, but circulation spreads it into the tank and piping. That's why we'd pick the 200 mg/L target over 100 mg/L for a DIY job, and why you keep going until you smell chlorine at every tap.
How Do You Mix, Add, and Circulate the Chlorine?
Shock chlorination takes six steps: prep the house, mix the bleach, add it to the well, wash down the casing, pull chlorine through every pipe, then seal the well and wait.
- Prep the house. Turn off the water heater at the breaker or gas control. Bypass or remove every carbon filter, sediment filter, softener, and reverse osmosis unit, because strong chlorine ruins carbon media and membranes. Pull the ice maker and fridge filter, too, and check each manufacturer's instructions.
- Mix the dose. Wearing goggles and gloves, put 5 gallons of clean water in the bucket, add your measured unscented household bleach, and stir. Never combine bleach with ammonia, vinegar, or other cleaners. The fumes are dangerous.
- Open the well. Switch off the pump breaker first. Unbolt the well cap or remove the vent plug and look at the wiring. If wires are frayed, wet, or tangled near the opening, stop and call a pro. Otherwise, pour the solution slowly through the funnel and keep splashes off the wiring.
- Wash down the casing. Attach the garden hose to an outdoor hose bibb and feed the other end into the well. Turn the pump breaker back on, open the bibb, and let water circulate for 15 to 30 minutes, until you smell strong chlorine at the hose end. Keep the hose end out of the dirt, and wipe it with the bleach mix if it touched the ground.
- Pull chlorine through the plumbing. Open each faucet one at a time, cold first, then hot, until you smell chlorine, then close it. Flush every toilet once. Run the shower, laundry, and outdoor spigots too. If one tap never smells of chlorine, repeat the circulation.
- Seal and wait. Turn off the hose, remove it from the well, and refit the cap with its gasket intact. Let the chlorine sit in the system for 12 to 24 hours. Don't drink, cook, bathe, or run laundry in that time.
How Do You Flush Without Dumping Chlorine Into the Yard or Septic?
Flush strongly chlorinated water outdoors through a hose, not through the house drains. A typical household septic can handle a modest amount of chlorine, but pushing hundreds of gallons through in a few hours can stress the bacteria that break down waste.
Run the hose from an outdoor spigot to a gravel area or patch of lawn that is downhill from the wellhead and well away from the septic tank, drain field, and any plants you care about. Never discharge it to a stream, pond, ditch, or storm drain, since chlorine harms aquatic life. Discharge rules vary by locality, so ask your county health department if you're unsure.
To cut the chlorine, add sodium thiosulfate to the flow, following the label. Keep the pump from running dry: if the well draws down, pause and let it recover.
Do the indoor taps last and in small bursts. Run each tap just long enough to clear it, and spread the work over a day or two so the septic isn't flooded. Flush the water heater, fridge line, and ice maker once the cold taps run clean. If you have an aerobic or pump-dosed septic system, ask the installer before you start.
How Long Until the Water Is Safe to Drink?
Plan on about 10 to 14 days from adding bleach to a lab result you can trust, and treat the water as unsafe to drink until a coliform test comes back clean.
| Stage | Typical time |
|---|---|
| Chlorine contact in the system | 12 to 24 hours |
| Flushing until chlorine is gone | Several hours to 2 days |
| Waiting before you sample | About 7 days (follow your lab's advice) |
| Lab results | 1 to 3 business days |
Check progress with chlorine test strips. Flush until there is no chlorine odor and the strip reads near zero at every tap. For reference, the EPA's maximum residual disinfectant level for public water systems is 4 mg/L, and most people taste chlorine well below that. A zero reading only means the shock is flushed out. It says nothing about bacteria.
For the sample, use your lab's bottle and instructions. That usually means the kitchen cold tap with the aerator removed, a few minutes of running water first, and never touching the inside of the cap. Get it to the lab within its hold time, which is commonly about 30 hours or less. Sampling too early is a mistake, because leftover chlorine can skew the result.
A negative result means you can drink the water again. Reinstall the filters, switch the water heater back on, and mark your calendar to retest in a year.
What Mistakes Make Shock Chlorination Fail?
The most common failures are guessing the dose, skipping circulation, cutting contact time, and leaving filters in line.
- Guessing the dose. Too little leaves bacteria alive, so use your own casing numbers.
- Old or scented bleach. Bleach weakens over time. Buy a fresh jug and check the percentage on the label.
- Skipping the circulation. Dumping bleach in and walking away treats the casing while the pipes stay untreated.
- Cutting the contact time. Eight hours isn't 12.
- Leaving filters in line. A carbon filter soaks up chlorine and is ruined, and it can keep harboring bacteria.
- Sampling from a dirty tap. Skip swivel spouts, taps with a hose attached, and any that leak.
- Ignoring the cause. If the cap is cracked or the casing sits below grade, bacteria will return.
When Should You Call a Well Professional?
Call a licensed well contractor if the test is positive again after one correct shock, if the wellhead or casing is damaged, or if the well has been flooded. A pro can inspect the well with a camera, replace the well cap or sanitary seal, extend the casing above grade, and pull the pump if needed. A service call often runs about $150 to $500, and repairs cost more. Rules on who may work on a well vary by state and county, so check with your county health department.
Also stop if you see wiring problems at the wellhead, if the well is in a pit or confined space, or if it's an older hand-dug or shallow well with a stone or concrete liner. Those are easy to contaminate and harder to disinfect.
Slimy deposits, rusty stains, or a rotten-egg smell can point to iron or sulfur bacteria. Shocking may help for a while, but the problem often returns, and a treatment system sized by a pro is the usual route. For repeated bacteria, ask about ultraviolet disinfection or continuous chlorination, again sized by a pro. NSF lists certified water treatment products you can check before you buy.
Your next step: find your well log, measure the water column, and call your lab to ask about sampling days before you buy the bleach.
Questions people ask
Can I use pool shock instead of household bleach?
Some agencies accept plain granular calcium hypochlorite, but the math is different because it's roughly 65% to 75% chlorine. It must contain no algaecide, stabilizer, or additives. For a first-time DIY job, regular bleach is easier to measure and safer to get right.
Is it safe to shower while chlorine is in the system?
It's best to wait. Water at 200 mg/L can irritate skin, eyes, and lungs, especially in a steamy bathroom. Wait until the chlorine is flushed and test strips read near zero.
Should I shock my well every year as maintenance?
No. Test the water for coliform at least once a year, and shock only when there's a reason such as a positive result, pump or well repair, or a flood. Repeated shocking without fixing the cause just delays the real problem.
Why does my water still smell of chlorine days later?
Chlorine can linger in the water heater, pressure tank, softener, or a dead-end pipe. Run those taps and flush the heater until the smell is gone. If it persists for more than a few days, check several taps with test strips.
What if my coliform test is positive after I shock the well?
Keep boiling or using bottled water. If you know you missed a step, such as short contact time or a tap that never smelled of chlorine, you can repeat the shock once and retest. Otherwise, or if the second result is also positive, call a well professional to look for the entry point.
Sources and further reading
- EPA Drinking Water EPA guidance on private wells, testing, and drinking water safety
- NSF Find certified water treatment products for after disinfection
Was this article helpful?