Fix and Furrow
Advertise

Part of our Heating and Cooling guide

Adding Insulation Over Old Attic Insulation: 6 Mistakes

Old fiberglass or cellulose hides leaks, blocked vents and gaps. Here is what to check with a tape measure before you buy bags.

Save to Pinterest

We may earn a commission when you buy through links on this page. It never changes what we recommend. Learn more

Attic floor with fluffy blown-in insulation, rafter baffles at the eaves and a depth ruler stapled to a joist
Photo: Denny Müller on Unsplash

The short answer

The biggest mistakes are skipping air sealing, blocking soffit vents, burying recessed lights and the attic hatch, adding a second vapor retarder, compressing old batts, and guessing at depth. Seal leaks first, install rafter baffles, then add insulation until the total reaches about R-49 in colder climates: roughly 13 to 15 inches of cellulose or 18 to 22 of fiberglass.

Typical cost
$600 to $1,800 DIY materials; $1,500 to $3,500 hired, for a 1,000 sq ft attic
Time needed
One to two weekends
Skill level
Intermediate

Key points

  • Air seal the attic floor before any new material goes down, because insulation slows heat but does not stop air leaks.
  • Install rafter baffles at every soffit bay and keep them taller than your final insulation depth.
  • Never add plastic, foil-faced or kraft-faced material on top of existing insulation.
  • Count depth in inches and convert to R-value using the bag's coverage chart, not a guess.
  • Stop and call a pro if you find vermiculite, knob-and-tube wiring, or damp, moldy insulation.
In this guide
  1. Why Does Topping Up Old Attic Insulation Go Wrong?
  2. Mistake 1: Adding Insulation Before Air Sealing the Attic Floor
  3. Mistake 2: Compressing Old Batts and Losing R-Value
  4. Mistake 3: Blocking Soffit Vents and Ventilation Paths
  5. Mistake 4: Burying Recessed Lights, Flues, and Attic Hatches
  6. Mistake 5: Adding a Vapor Retarder Over Existing Insulation
  7. Mistake 6: Guessing Depth Instead of Measuring to Target R-Value

Before you buy a single bag, put a tape measure in the attic and write down three numbers: the inches of insulation you have now, the inches of clear space at the eaves, and the inches you need to reach your target. Most of the expensive mistakes below show up in those measurements.

Why Does Topping Up Old Attic Insulation Go Wrong?

Topping up goes wrong because the old layer hides problems, and new blown-in insulation buries them for good. Gaps, dirty streaks, blocked vents and uncovered fixtures all vanish under fresh fluff. Your heating bill doesn't forget them.

ENERGY STAR and Department of Energy guidance generally points to about R-49 or more for attics in colder climates, and lower numbers in warm southern zones. Look up your climate zone on the ENERGY STAR or Energy Saver pages, since local code can differ. The table is the short version of what follows.

MistakeWhat it costs youTape-measure check
No air sealingWarm air bypasses the new layerDark, dirty insulation near walls and penetrations
Compressed battsLess R-value per inchFluffy depth versus flattened depth
Blocked soffit ventsMoisture, frost, ice damsClear channel at the eaves
Buried lights and hatchHeat risk, air leaksBarrier taller than final depth
Second vapor retarderTrapped moistureNothing foil, kraft or plastic on top
Guessing depthFalling short of target RInches times R per inch

Mistake 1: Adding Insulation Before Air Sealing the Attic Floor

Skipping air sealing is the costliest mistake, because insulation slows heat but does not stop warm indoor air from leaking into the attic. The old layer covers every gap, so the attic looks fine.

The cost is a new layer that gets bypassed through the holes, plus moist air reaching a cold roof deck, which is how frost forms on roof sheathing in winter.

The fix is to pull insulation back and seal first. Hit the top plates of interior walls, wire and plumbing penetrations, duct boots, and gaps around chimneys and flues. Use caulk for small cracks and expanding foam for larger ones. Around a chimney or flue, use sheet metal and high-temperature sealant, not foam. Materials often run $100 to $300. Dark, gray-streaked insulation against the floor is a sign air has been moving through it.

Mistake 2: Compressing Old Batts and Losing R-Value

Compressing old batts loses R-value because fiberglass insulates by trapping air, and squeezed insulation traps less of it. It usually happens when people stuff, stomp or lay boards directly on the old layer.

The loss is silent. A flattened batt can deliver noticeably less than its label says, and you still pay to cover it. Leave the old material alone and don't pack it down. If you need to move around, lay planks across the joists. Blowing loose-fill over batts is common and fine.

For most attics with old batts, we'd pick loose-fill cellulose. It reaches the same R-value in fewer inches and settles into gaps around wiring. It's denser than fiberglass, so look at the ceiling below first if the drywall is sagging or water-stained.

Measure what's really there, not what the label claimed years ago. Six inches of settled old fiberglass is closer to R-13 to R-16 than R-19.

Mistake 3: Blocking Soffit Vents and Ventilation Paths

Blocking soffit vents with new insulation shuts off the airflow that keeps the roof deck dry. Blown material drifts into the eaves easily, and nobody sees it happen.

The cost shows up later as damp sheathing, mold, shortened shingle life and ice dams. Many codes use a rule of thumb of 1 square foot of net free vent area per 150 square feet of attic floor, sometimes 1 per 300 with balanced vents. Confirm what your jurisdiction requires.

The fix is rafter baffles in every bay that meets a soffit. They're foam or cardboard, typically a few dollars apiece. Staple them to the roof deck so they hold a clear channel, and make sure they rise above your final insulation height. Then check from inside the attic that air can still travel from the soffit up past the insulation.

Mistake 4: Burying Recessed Lights, Flues, and Attic Hatches

Burying these features is a mistake because each one needs either clearance or its own air seal. Blowing right over them is faster, which is why people do it.

Start with the recessed lights and read the housing label. Only IC-rated fixtures can be covered by insulation, and even those leak air unless they're rated airtight. Non-IC cans need a code-approved cover or replacement, which is an electrician's job, and some jurisdictions want a permit for it. Flues and chimneys need a metal dam that holds insulation back from the flue by the distance your code and the flue manufacturer specify, typically 1 to 3 inches depending on type. If you can't tell what kind of flue you have, ask a licensed pro.

The attic hatch is the leakiest hole in many ceilings. Build a dam around the opening as tall as your final depth, weatherstrip the lid, and glue rigid foam board to the top of it. Skip this and you've built a chimney with a door.

Mistake 5: Adding a Vapor Retarder Over Existing Insulation

Adding a vapor retarder on top of existing insulation is a mistake because it can trap moisture between two barriers. In cold climates the retarder belongs on the warm side, which is the ceiling below, and painted drywall often handles that job.

It happens when people buy faced batts or lay plastic sheeting to be thorough. The cost is condensation inside the insulation, which lowers R-value and can rot framing. Blown-in material is unfaced, and that's what you want. Kraft paper on old batts, facing the ceiling below, can stay. Just don't lay a second faced layer on top. Humid, hot climates follow different rules, so check local code before adding any barrier. The Energy Saver site covers attic insulation and moisture basics.

Mistake 6: Guessing Depth Instead of Measuring to Target R-Value

Guessing depth leaves you short of your target, because R-value depends on material and thickness together. Loose-fill fiberglass gives roughly R-2.2 to R-2.7 per inch. Cellulose gives roughly R-3.2 to R-3.8. Use the coverage chart printed on your bag, since products vary.

So a total of R-49 means about 18 to 22 inches of fiberglass or 13 to 15 inches of cellulose, starting from a bare floor. Count what you have first. If 6 inches of old fiberglass is about R-13 to R-16, you need roughly R-33 to R-36 more, which is around 9 to 11 inches of cellulose. Add the R-values together. Don't add inches.

Staple depth rulers to joists in several spots before blowing, and aim slightly over target because loose-fill settles. Count bags from the chart, not by eye. Your next step: measure the attic this week, then seal and baffle before you rent the blower.

Questions people ask

How do I know if my attic needs more insulation?

If the insulation sits level with or below the tops of the joists, you almost certainly need more. Measure the depth in several spots and compare the total R-value to the level recommended for your climate zone.

Do I need to remove old insulation first?

Usually not. Remove it only if it is wet, moldy, contaminated by rodents, or mixed with vermiculite or other hazards. Otherwise, leave it in place and build on top.

How much does hiring a pro to add blown-in insulation cost?

Typical U.S. pricing is often around $1.50 to $3.50 per square foot, depending on region, depth, material and how much air sealing is included. Ask whether sealing and baffles are part of the quote.

Can I cover knob-and-tube wiring with blown-in insulation?

Generally no. Knob-and-tube wiring was designed to shed heat into open air, and many codes and insurers restrict covering it. Have a licensed electrician inspect or replace it first.

How long does blown-in attic insulation last?

Properly installed cellulose and fiberglass can last decades if they stay dry. Settling, moisture and pests reduce performance, so check the depth every few years.

Sources and further reading

Elsewhere in Heating, Air & Water