Fix and Furrow
Advertise

Part of our Home Repair Troubleshooting guide

Roller Shade Won't Stay Up? Causes, Checks and Fixes

Drifting usually traces to a slipping clutch or a tired spring, and you can check both in minutes without taking the shade down.

Save to Pinterest

We may earn a commission when you buy through links on this page. It never changes what we recommend. Learn more

Partly lowered white roller shade on a window with a metal mounting bracket visible at the top corner
Photo: CDC on Unsplash

The short answer

A roller shade that won't stay up usually has a slipping chain clutch, a worn catch, or a spring that has lost tension. Lower the shade halfway and let go to see which. On a spring roller, adding two or three hand turns of tension often fixes it. A slipping clutch means replacing the part or the roller kit, typically $20 to $80 for a standard size.

Typical cost
$0 for an adjustment; about $20 to $80 for a standard replacement roller kit; $75 to $200 or more for a service call
Time needed
10 minutes for checks and a tension adjustment; 30 minutes to an hour to swap a roller kit
Skill level
Beginner

Key points

  • Work out whether you have a chain clutch or a spring roller first, because the likely cause and the fix differ.
  • On a spring roller, a relaxed spring is a common culprit, and two or three hand turns of added tension often bring it back.
  • Chain clutches can't be tuned, so a slipping one means replacing the clutch or the whole roller kit.
  • Drifting that shows up only in cold or damp weather suggests a marginal mechanism rather than a loose bracket.
  • If the shade still creeps after three tension adjustments, stop and replace the mechanism.
In this guide
  1. How do I check the brake or clutch first?
  2. Is the spring tension too weak or worn out?
  3. Could the shade be too heavy for its mechanism?
  4. Do loose brackets or a misaligned roller cause drifting?
  5. Can a bent hem bar make a shade drift?
  6. How do I adjust spring tension without damaging the shade?
  7. When should I replace the roller kit or call a pro?

Check what's at the end of your shade first. If you raise it by pulling a chain loop, it has a chain clutch, and drifting usually means the clutch is slipping. If you tug the hem and let it snap up, it's a spring roller, and drifting usually means a tired spring or a worn catch. Every check below works with the shade still mounted.

How do I check the brake or clutch first?

Lower the shade halfway, let go, and watch it for a full minute; if it creeps, the clutch or catch isn't holding. That test takes less time than any other check and tells you which mechanism to look at.

On a chain shade, look at the clutch housing at the end of the tube. The chain should sit in the teeth without a kink, and the connector link shouldn't be snagged. A chain pulled tight against the wall or bracket can also tug the clutch out of position. Wipe the housing with a dry cloth, and skip the oil, since lubricant can make a clutch slip.

On a spring roller, pull the shade down a few inches and release it gently. If it creeps or rolls back up on its own, the catch is worn or the spring is too weak for the weight of the fabric.

Watch for timing. A shade that holds on mild days but drifts on cold mornings or in a steamy bathroom likely has a mechanism that's already marginal, with the temperature or moisture tipping it over. A loose bracket is a less likely explanation.

Is the spring tension too weak or worn out?

Yes, on a spring roller a weak or worn spring is a common reason the shade won't hold. The spring balances the weight of the lowered fabric, and after years of use it loses some of its pull.

The signs are a shade that rises sluggishly, stops short of fully rolled, or needs a hard tug to get going. A spring that has relaxed can be re-tensioned by hand, as described below. One that rattles, clicks, or has gone dead can't practically be repaired.

Likely causeQuick checkFix
Slipping chain clutchShade creeps after you release the chainReseat chain; replace clutch or roller kit
Weak spring or worn catchSlow rise, creeps from halfwayAdd two or three hand turns; replace if it keeps failing
Fabric too heavy for the mechanismRecently changed fabric or added a linerLighter fabric or heavier-duty roller
Loose bracket or misaligned rollerBracket wiggles; shade sits off levelRe-anchor bracket, reseat pins
Bent hem barFabric rolls crookedStraighten or replace the bar

Could the shade be too heavy for its mechanism?

Yes, a shade can be too wide or heavy for its mechanism, and that's the likely cause when it drifted from day one or after a fabric change. Each mechanism is built for a range of widths and fabric weights, and a thick blackout roller shade on a wide window can exceed what a standard spring or clutch can hold.

Look for what changed: a blackout liner, a laminated fabric, a heavier hem bar. Wider, heavier shades generally need a larger-diameter tube and a heavier-duty clutch. If the manufacturer lists a maximum width or weight, compare it to your shade. The fix is a lighter fabric or a roller kit rated for the size.

Do loose brackets or a misaligned roller cause drifting?

Yes, they can, though a spring or clutch problem is the likelier cause. When a roller shade bracket comes loose, the tube tilts, the pins can slip in their slots, and the shade may lose its grip on the catch.

Push gently on each bracket. Any movement means the screws aren't holding. Brackets set into plain drywall are common offenders, and the screw holes are often stripped. Move the bracket to a stud or the window frame if you can, or use drywall anchors rated for the load. Don't drive the old screws back into the same holes. In a house built before 1978, assume old trim paint may contain lead and keep drilling dust to a minimum.

Then check the fit. Both pins should sit fully in their slots with a little side-to-side play. Too tight and the shade binds. Too loose and it can jump a pin. Confirm the roller is level, too.

Can a bent hem bar make a shade drift?

Rarely, but a bent hem bar can make the fabric roll crooked, and a crooked roll adds drag and uneven load that can work against the mechanism. Lower the shade fully and look at the hem; the bar should be straight and the fabric should hang square.

If the shade winds up to one side, suspect the bar or a crooked fabric attachment. Slide the bar out of its pocket and flex it straight by hand if it's light aluminum or plastic, and replace it if it won't straighten. Fabric that was cut or attached off square won't be fixed by re-rolling. It needs to be re-cut or replaced.

How do I adjust spring tension without damaging the shade?

Take the shade out of its brackets and roll the fabric up by hand one turn at a time, testing after each turn, because over-tightening can make it snap up hard enough to damage the fabric or the catch. This applies to spring rollers only, since chain clutches have no adjustable tension.

  1. Lower the shade about halfway.
  2. Working from a stable stepladder, lift the shade out of the brackets and hold the tube so the fabric doesn't unroll.
  3. Roll the fabric up by hand, in the direction it normally winds, for one full turn.
  4. Seat the flat pin in its bracket slot first, then the round pin, and test.
  5. If it still creeps, repeat with one more turn. If it snaps up too fast, take a turn back out.

Stop after three attempts. A spring that needs repeated boosting is finished. If your shade came with instructions for its roller, follow those over this general method.

When should I replace the roller kit or call a pro?

Replace the mechanism when the shade still creeps after two or three tension adjustments, the clutch is skipping or grinding, or the spring rattles or has gone limp. A standard-size replacement roller kit often runs about $20 to $80, depending on width and tube size, and swapping one commonly takes 30 minutes to an hour with a screwdriver.

We'd pick replacement over repair for any inexpensive, standard-size shade, since a service visit can cost more than a new kit. For an expensive custom shade, call the maker or installer first, because the mechanism may be under warranty. A service call commonly runs $75 to $200 or more depending on your area.

Call a pro for motorized shades that drift. That's a motor or limit-setting problem, not a spring one, and a hardwired unit needs a licensed electrician. A cordless roller shade that keeps failing in a humid bathroom may simply be the wrong product for the room, and faux wood blinds or a moisture-rated shade are worth a look.

Your next step takes two minutes. Lower the shade halfway, let go, and time how long it holds. Then measure the shade width and the tube diameter, and note the mechanism type before you buy anything.

Questions people ask

Why does my roller shade go down by itself overnight?

A slow overnight drop usually means the clutch or spring is barely holding. Temperature swings can tip a marginal mechanism over the edge, so try adding spring tension on a spring roller, or replace the roller kit if the drift continues.

Can I fix a roller shade clutch myself?

Usually not. Many clutches are built as sealed units and aren't meant to be opened. You can reseat the chain and clear lint, but a slipping clutch generally means swapping the clutch or the whole roller kit.

Why does my roller shade snap up too fast after I adjusted it?

You added too much spring tension. Take the shade out of the brackets, unroll the fabric by one turn, and rehang it. Make changes one turn at a time and test after each.

Will a bigger roller tube stop my shade from drifting?

It can, if the shade is wide or heavy. Larger tubes usually come with stronger clutches and springs. Check that the new tube fits your brackets and window width before ordering.

What do I measure to buy a replacement roller kit?

Measure the fabric width, the overall length from pin to pin, and the tube diameter. Note whether you have a chain clutch or a spring mechanism, and check the pin style at each end so the new roller seats in your brackets.

Sources and further reading

Elsewhere in Decorating