Fix and Furrow
Advertise

How High to Hang a Curtain Rod, and How Wide It Should Be

Standard windows, short windows near the ceiling, and the fabric math that decides how long the rod needs to be.

Save to Pinterest

We may earn a commission when you buy through links on this page. It never changes what we recommend. Learn more

Floor-length curtain panels hung on a rod mounted above a living room window frame
Photo: EZcurtain Life on Unsplash

The short answer

Mount the curtain rod 4 to 6 inches above the window frame and extend it 3 to 8 inches past each side so open panels stack on the wall instead of covering glass. Buy panels with a combined flat width of 2 to 2.5 times the rod length, and hang them to about 1/2 inch above the floor.

Typical cost
$20 to $120 for a rod and brackets per window; panels cost extra
Time needed
30 to 60 minutes per window
Skill level
Beginner

Key points

  • For an 8-foot ceiling, about 5 inches above the frame is the safest rod height.
  • Rod length equals frame width plus 3 to 8 inches on each side, and up to 12 inches if you want most of the glass clear.
  • Fabric should total roughly 2 to 2.5 times the rod length, or the panels look flat when closed.
  • Measure panel length from the bottom of the rings or clips, not from the rod itself.
  • Keep fabric well clear of radiators and baseboard heaters, and anchor brackets into studs or properly rated anchors.
In this guide
  1. What Two Measurements Decide Curtain Rod Placement?
  2. How High Above the Window Should the Rod Go?
  3. How Far Past the Frame Should the Rod Extend?
  4. How Long Should Curtains Hang?
  5. How Much Fabric Do You Need for Fullness?
  6. Measuring Worksheet for One Window
  7. What If the Wall, Trim, or Radiator Gets in the Way?

Hang the rod 4 to 6 inches above the window frame and extend it 3 to 8 inches past each side. That fits most rooms with 8-foot ceilings. The exceptions are short windows near the ceiling, thick fabric stacks, and walls that won't cooperate.

What Two Measurements Decide Curtain Rod Placement?

Rod height and rod length drive every other decision, and you measure both from the outside edge of the frame and trim, not from the glass. Height sets how tall the room feels and how long your panels must be. Length sets how much glass stays uncovered when the curtains are open.

Settle the height first. Panel length depends on it, and fabric length is the one thing you can't fix after you buy.

How High Above the Window Should the Rod Go?

On a standard window with an 8-foot ceiling, mount the rod 4 to 6 inches above the top of the frame, and go higher if the ceiling is taller. Hanging higher draws the eye up and makes the window look larger than it is. We'd pick about 5 inches above the frame and not overthink it. If the wall above the window is short, go lower rather than cramming the brackets against the ceiling.

SituationRod heightWhy
Standard window, 8-foot ceiling4 to 6 inches above frameClears the trim and reads as one clean line
9-foot or taller ceiling6 to 10 inches above frame, or just below crown moldingKeeps the panels in proportion with the wall
Frame within 8 inches of the ceiling2 to 3 inches above the frameBrackets and rod still need room to clear the casing
Frame meets the ceilingCeiling mount, or skip the rodNo wall space for brackets

A short window near the ceiling won't give you a generous gap. Mount as high as the brackets allow, and keep at least 2 inches above the frame so the panel hangs over the trim instead of catching on it. If even that won't fit, a shade is the cleaner fix. Cellular shades and similar fitted options sit inside the window opening and need no wall space above it.

How Far Past the Frame Should the Rod Extend?

Extend the rod 3 to 8 inches past each side of the frame so the open panels rest on the wall, not over the glass. Three inches is the minimum that looks intentional. Eight is more common when you want the window to look wider and let in full light. For most windows, 6 inches is a sound default.

Here is the catch. Heavy lined curtain panels often stack back to about a quarter to a third of their flat width, depending on the fabric and heading style. On a 52-inch rod with 2x fullness, each panel holds about 52 inches of flat fabric, so expect 13 to 17 inches of stack per side. A 6-inch extension leaves some fabric over the glass. Reaching 12 inches per side gets close to clearing it, but only if the wall has room. Beside a corner or a door, accept a little overlap rather than crowding the edge.

Check whether the listed rod length includes the finials. It often doesn't, and that changes how close the rod ends sit to a neighboring wall.

How Long Should Curtains Hang?

Hang panels so they stop about 1/2 inch above the floor in most rooms. That gap clears the rug edge and lets the fabric swing without dragging dust. Sill-length panels end about 1/2 inch below the sill or apron and suit windows over radiators, desks, or kitchen counters. A puddle adds 1 to 3 inches of extra fabric on the floor, and we'd skip it in any room with pets, kids, or a vacuum you actually use.

A rod pocket panel hangs close to the rod, so measure from the rod itself and add the heading allowance above it if the panel has one.

How Much Fabric Do You Need for Fullness?

Plan on flat fabric 2 to 2.5 times the rod length for standard panels, and more for sheers. Less than that and the folds stretch out flat when the curtains are closed, which looks thin.

Fabric typeFullness multiplier
Sheers and light voile2.5 to 3 times
Standard lined or unlined panels2 to 2.5 times
Heavy or blackout curtainsAbout 2 times, with 1.5 times as the floor

Multiply your rod length by the number in the table to get total fabric width. Ready-made panels commonly run 50 to 54 inches wide, so divide and round up. Fabric weight and how well the panels close also affect comfort. The Department of Energy's Energy Saver site covers how window coverings change heat gain in summer and heat loss in winter.

Measuring Worksheet for One Window

Six numbers, taken in order, give you the whole plan for one window, and all you need is a tape measure. The example below uses a 40-inch frame.

  1. Frame width, A. Measure the outside edge of the trim. Example: 40 inches.
  2. Extension per side, B. Pick 3 to 8 inches, or up to 12 for maximum glass clearance. Example: 6 inches.
  3. Rod length. A plus two times B. Example: 52 inches.
  4. Rod height. Measure from the floor to the top of the frame, then add 4 to 6 inches. Example: 82 inches plus 5 equals 87 inches.
  5. Panel length. Rod height minus about 2 inches of ring drop, minus 1/2 inch of floor clearance. Example: about 84 1/2 inches.
  6. Fabric width. Rod length times fullness. Example: 52 times 2 equals 104 inches, so two 54-inch panels.

Mark bracket spots a few inches in from each rod end, usually 2 to 4 inches depending on the finials. Add a center support bracket on any rod longer than about 48 inches, which includes the 52-inch example above. Check the maker's instructions for the exact limit, since it varies with rod diameter and fabric weight.

What If the Wall, Trim, or Radiator Gets in the Way?

When something blocks the standard spot, change the bracket or the panel length, not the whole plan. Deep window casing calls for brackets with a longer projection so the rod and rings clear the trim. Crown molding may force the rod below it, or you can use brackets that project far enough to clear it.

Heavy blackout curtains can pull weak anchors right out of the wall. Screw brackets into studs when you can, locating them with a stud finder. Where a bracket lands between studs, use drywall anchors rated well above the load. The plastic ones that come with many rods are often marginal for heavy fabric.

A radiator or baseboard heater under the window changes the length decision. Keep fabric several inches clear of any heat source and follow the heater maker's stated clearance, which varies by model. In practice that means sill-length panels, or floor-length panels hung wide of the unit. Fabric draped over a heater is a scorch and fire risk, and it traps heat away from the room.

If none of it fits, price a shade before you fight the wall.

Before you drill, stick painter's tape on the wall at the rod height and at both end points, step back across the room, and look. Move the tape, not the holes.

Questions people ask

Should the curtain rod go all the way to the ceiling?

It can, and it makes a room feel taller. Mounting within a few inches of the ceiling works well with 9-foot ceilings or windows already near the top. Keep the rod low enough that the brackets and rings clear any crown molding.

How do I hang curtains on two windows close together?

Use one long rod across both windows if the gap between frames is a foot or less. The panels then sit outside the pair and the wall reads cleaner. For wider gaps, treat each window separately and keep the rods at the same height.

Can I mount curtains inside the window frame?

Yes, but it works best for café curtains, sheers, or tension rods in a deep casing. You lose the extra width and light control of an outside mount, and fuller panels will crowd the glass. For floor-length panels, mount outside the frame.

Does rod diameter change how high to hang it?

Only slightly. A thicker rod, such as 1 1/8 inches or more, projects further from the wall and needs a deeper bracket, but the height above the frame stays the same. Thicker rods also sag less under heavy fabric.

Should every window in a room have the rod at the same height?

Yes, in most rooms. Measure the rod height from the floor and use the same number on every window on that wall, based on the window that needs the most clearance. Matching heights keeps the top line of the curtains straight even when the windows differ in size.

Sources and further reading

Elsewhere in Decorating