Fix and Furrow
Advertise

Part of our Roofing and Exterior guide

Siding Installation Mistakes Around Windows That Cause Leaks

Leaks usually trace to flashing that's missing or out of order, not the siding. Check every window while the walls are still open.

Save to Pinterest

We may earn a commission when you buy through links on this page. It never changes what we recommend. Learn more

House wall with house wrap and flashing tape around a window opening before siding goes on
Photo: Manuela Johnston on Unsplash

The short answer

Window leaks after re-siding usually come from five errors: caulk used in place of flashing, head flashing layered in the wrong order, a missing or unsealed sill pan, nails through flashing tape, and bad gaps at trim. Inspect every window before siding covers it. Flashing correctly often adds roughly $75 to $250 per window; repairing rot later commonly runs $500 to $2,500 or more.

Typical cost
$75 to $250 per window to flash correctly; $500 to $2,500+ to repair a leaking window later
Time needed
15 to 30 minutes per window to inspect; a hose test adds about an hour
Skill level
Intermediate

Key points

  • Caulk is a backup seal, never a substitute for flashing tape and metal head flashing.
  • Layers must overlap like shingles: the wrap above laps over the head flashing, so water runs over the next layer instead of behind it.
  • A missing or unsealed sill pan is the leak you won't see until the sill and framing are soft.
  • Photograph and inspect every window before siding goes over it, because that is the only cheap time to catch a mistake.
  • Flashing correctly often adds roughly $75 to $250 per window, while repairing rot later commonly runs $500 to $2,500 or more per opening.
In this guide
  1. Why Do Windows Leak After Re-Siding?
  2. Mistake 1: Caulking Instead of Flashing the Head and Sides
  3. Mistake 2: Installing Head Flashing in the Wrong Layer Order
  4. Mistake 3: Skipping or Improperly Sealing the Sill Pan
  5. Mistake 4: Nailing Through or Too Close to the Nailing Fin
  6. Mistake 5: Leaving Gaps Between Trim and Siding Edges
  7. How Do You Inspect Window Flashing Before the Crew Leaves?
  8. What Does a Window Leak Repair Cost Compared With Doing It Right the First Time?

The surest way to get a leak around a window after new siding is to let the crew rely on caulk. Most of the other mistakes here share the same root: water-shedding layers installed out of order, so water runs behind a layer instead of over it. Get the order right and most leaks never start.

Why Do Windows Leak After Re-Siding?

Windows leak after re-siding because each opening cuts through the wall's weather barrier, and the flashing around it works only if each layer laps over the one below it, shingle-style.

Siding isn't waterproof. It sheds most rain, and the house wrap behind it handles what gets past. At a window, flashing ties those layers to the frame. A crew that treats the window as a trim detail tends to focus on how it looks from the street, not on the hidden sequence. The damage shows up slowly: a stain under the sill, soft trim, bubbling paint, sometimes a year or two later.

Existing windows are the harder case. If new windows go in with the siding, the crew controls the whole sequence. If you're keeping the old ones, the crew has to tie new work into flashing they didn't install, and shortcuts tend to happen there.

Mistake 1: Caulking Instead of Flashing the Head and Sides

Caulk alone is not flashing, and a crew that seals window edges with sealant instead of flashing tape and metal is betting your wall on a joint that tends to open over time.

It happens because caulk is fast, looks tidy on day one and hides gaps. But sealant moves with the seasons, ages in sunlight and loses adhesion on dusty or wet surfaces. When it lets go, nothing behind it stops the water.

Get the scope in writing: self-adhesive window flashing tape on the jambs and head, plus metal head flashing, with polyurethane sealant (or another sealant the window and tape makers approve) used only as a secondary seal. It's the most useful line you can add to a siding contract.

Mistake 2: Installing Head Flashing in the Wrong Layer Order

Head flashing installed in the wrong layer order lets water run behind it instead of over it, which sends rain into the wall right above the window.

Done correctly, the drip cap or Z-flashing sits on top of the window trim or fin, and the house wrap above it laps down over the flashing's upper edge. Water running down the wrap lands on the metal and drips out past the trim. Done wrong, the flashing is slid on top of the wrap, or the wrap is tucked behind it, and water follows the wrap behind the metal and into the opening.

This is an easy error in re-siding, where the wrap is already up and flashing gets added afterward. It's also the hardest to spot once siding is on. The result is a rotted header and wet insulation above the window.

Mistake 3: Skipping or Improperly Sealing the Sill Pan

A sill pan is a waterproof tray under the window that catches water that gets past the frame and directs it outward, and skipping it or leaving the corners unsealed is one of the costliest flashing mistakes.

The head flashing keeps water off the window from above; the pan handles whatever gets in anyway. A good one has a slope or back dam, runs up the jambs a few inches and has sealed corners. It can be formed from flashing tape, a preformed pan or a sloped sill.

Crews skip it because it's hidden and slows the work. The sill is also where water pools, so it rots first. If your windows are staying put, a pan usually can't be added without pulling the window, so ask the crew to probe the sill for softness and call you before covering anything suspicious.

Mistake 4: Nailing Through or Too Close to the Nailing Fin

Nails driven through flashing tape, or in the wrong spots on the nailing fin, create the exact holes the flashing was meant to prevent.

Window makers specify a fastener pattern for the fin, and siding fasteners shouldn't land on it or puncture the tape over it. Hurried installers also nail through J-channel or trim where it overlaps the fin, and each hole is a path for water. With vinyl, nail J-channel in the center of the slots and leave it loose enough to move. Nailing too tight causes waves as well as leaks.

Mistake 5: Leaving Gaps Between Trim and Siding Edges

Siding that butts tight against window trim, or leaves a wide gap sealed only with caulk, lets water into the joint where trim and siding meet.

Many siding makers call for a small gap, often about 1/4 inch, between siding ends and trim, filled with sealant. The figure varies, so check your siding's installation instructions. Too tight and the boards have no room to expand and the joint can't be sealed. Too wide and the sealant has nothing to grip, so add backer rod before sealing. Siding should also stop short of the top of the head flashing so water can drip free instead of wicking up.

How Do You Inspect Window Flashing Before the Crew Leaves?

Inspect each window while the wrap and flashing are still visible and before siding covers them, using a short checklist and photos.

Tell the crew at contract time that you want a hold point, a pause for your inspection, before each wall is closed up. For upper floors, check from the crew's scaffold or a ladder set on level ground with someone footing it. Then look at:

  1. Sill: pan or tape is continuous, with a back dam and sealed corners.
  2. Jambs: tape laps over the sill layer, not under it.
  3. Head: metal head flashing is visible, and the wrap above laps over it.
  4. Tape: no wrinkles, open edges, or nail holes through it.
  5. Photos: take a dated picture of each window for your records.

The table shows the general order. If the window maker's or wrap maker's instructions differ, theirs win.

LayerGoes onLaps over
Sill panFirstSheathing and wrap below
Jamb flashing tapeSecondSill pan edges and fin sides
Head flashing tape and metalThirdTop fin and jamb tape
House wrap aboveLastHead flashing

What Does a Window Leak Repair Cost Compared With Doing It Right the First Time?

Repairing a window leak after siding is installed typically costs several times more than flashing it correctly, because you pay to remove siding and fix whatever has rotted.

ItemTypical rangeWhat drives it
Proper flashing at install, per window$75 to $250Window size, metal head flashing, local labor
Pull siding and reflash one window$300 to $900Siding type, access, whether pieces break
Replace rotted sill, trim and sheathing$500 to $2,500Extent of rot, finishes, paint
Framing, insulation and interior repairs$2,500 to $8,000+Header or stud damage, drywall, mold

Prices vary widely by region and house. Rot that reaches framing, or any sign of mold, is a job for a licensed contractor.

Window flashing is also a code issue. Model codes published by the International Code Council call for flashing at exterior openings, though your local building department decides what applies, and permit rules for re-siding vary by town. Call them before work starts. The FTC's consumer advice site covers hiring contractors and reading a home improvement contract.

Before you sign, add three lines to the contract: flashing tape and metal head flashing at every window, a hold point for your inspection, and photos of each opening before siding goes on.

Questions people ask

How soon after new siding will a bad flashing job show up?

Sometimes with the first wind-driven rain, but often not for a year or more. Slow leaks soak insulation and sheathing quietly, so stains and soft trim appear well after the crew is gone.

Can I fix a leaking window by re-caulking it?

Fresh sealant can slow a leak that comes from a failed joint, but it won't fix missing or backward flashing. If the leak returns, the siding likely needs to come off at that window so the flashing can be corrected.

Should the siding crew or a window installer handle flashing?

Either can, but one party must own it in writing. Problems pile up when the window installer assumes the siding crew will flash and the siding crew assumes the reverse.

Is a sill pan required on every window?

Many manufacturers and building practices call for one, but requirements depend on the window maker's instructions and your local code. Check the window's installation sheet and ask your building department.

What does a window leak look like from inside the house?

Common signs are a stain below the window, peeling paint on the sill or casing, soft or swollen trim, and a musty smell. A moisture meter on the interior trim can confirm dampness before damage is visible.

Sources and further reading

Elsewhere in Remodeling