Fix and Furrow
Advertise

Part of our Roofing and Exterior guide

Wood Rot Repair Cost in 2026: Siding Patch vs. Full Re-Side

The price depends less on the rotted boards you can see than on how much sheathing and framing is damaged behind them.

Save to Pinterest

We may earn a commission when you buy through links on this page. It never changes what we recommend. Learn more

Close-up of rotted wood lap siding boards near a window corner on a house exterior
Photo: Jon Moore on Unsplash

The short answer

Wood rot repair cost depends on how far the damage goes. A few rotted siding boards run $300 to $1,000, trim or a window sill $400 to $1,500, and a wall section with sheathing $1,500 to $4,000. Framing repair starts near $600, and a full wood re-side costs $12,000 to $40,000. Probe for hidden rot first.

Typical cost
$300 to $1,000 for a few boards; $12,000 to $40,000 for a full cedar re-side
Time needed
One day for a few boards; one to three weeks for a whole house
Skill level
Intermediate

Key points

  • A handful of rotted boards with sound sheathing usually costs $300 to $1,000, mostly labor and a service-call minimum.
  • Hidden sheathing or framing rot is what turns a $700 repair into a $3,000 one, so probe the wall before you accept a quote.
  • Homes built before 1978 may need lead-safe work practices, which adds cost to any paint-disturbing repair.
  • Patching is a false economy when rot shows up on several walls or you would pay for scaffolding twice.
  • Get every contractor to price the same written scope, including a unit price for hidden damage.
In this guide
  1. What does it cost to replace rotted wood siding in 2026?
  2. How much does wood rot repair cost by type of repair?
  3. Cost table: materials, labor, and rot repair by scope
  4. What pushes the price up?
  5. What lowers the bill?
  6. Spot repair or full re-side: how to decide
  7. DIY or hire out for wood siding repair?
  8. How to get quotes you can actually compare

The rotted board you can see is rarely the whole bill. Wood rot repair cost starts at a few hundred dollars for a handful of boards. Once water has reached the sheathing or the studs, the same wall can cost several times that, and re-siding the whole house starts to make sense.

What does it cost to replace rotted wood siding in 2026?

Expect about $300 to $1,000 for a handful of boards, $1,500 to $4,000 for a wall section with sheathing repair, and $12,000 to $40,000 for a whole house in cedar. These are typical U.S. ranges, and your region, house height, and board profile will move them.

Small jobs run roughly $5 to $15 per square foot, which looks steep next to full-install pricing. Contractors charge a minimum for a service call, spend time finding the edge of the rot, and have to match an existing profile and paint.

For comparison, whole-house installed and painted prices run roughly $9 to $18 per square foot for cedar lap siding, $6 to $14 for fiber cement siding, and $4 to $9 for vinyl. Most houses have around 1,500 to 2,500 square feet of wall after you subtract windows and doors, which is where the whole-house ranges come from.

How much does wood rot repair cost by type of repair?

Most exterior wood rot repair costs between $100 and $1,500 per repair, and the price depends on whether the fix is a patch, a replacement piece, or structural carpentry. Siding is only one place rot shows up, so here are the other common ones.

RepairTypical costWhat drives it
Single board or short trim piece$100 to $400Minimum visit fee, priming, paint matching
Trim, fascia, or rake board$8 to $25 per linear footHeight, profile, painting
Window sill or door threshold$150 to $600Epoxy patch at the low end, full replacement at the high end
Door jamb or window casing$300 to $1,200Flashing repair, hanging the door or window again
Sheathing behind siding$2 to $6 per square footSize of the wet area
Studs or sill plate$600 to $3,000+Temporary support, access, framing length

Carpenters typically bill about $50 to $110 per hour, and many set a minimum of one to two hours. That minimum is why one rotted board costs $100 to $400 and ten boards in the same spot cost only a few times more.

For small, shallow rot, epoxy consolidant and filler can save the original wood. DIY kits usually run $25 to $80, and a pro doing the same repair on a sill or trim joint often charges $100 to $400. Epoxy works when the wood is mostly sound and the moisture source is fixed. It is the wrong choice for soft, crumbling, or structural wood, which has to come out.

Cost table: materials, labor, and rot repair by scope

Labor is the bigger share of every scope below, from a few boards to a whole house, and the totals include painting.

ScopeMaterialsLaborTypical total
Replace 3 to 6 boards, sheathing sound$30 to $200$250 to $800$300 to $1,000
Corner board, window trim, or door casing rot$50 to $300$300 to $1,200$400 to $1,500
One wall section (50 to 100 sq ft) with sheathing patch$300 to $900$1,000 to $3,000$1,500 to $4,000
Studs or sill plate repair behind siding$100 to $600$500 to $2,500$600 to $3,000+
One full elevation (200 to 400 sq ft), cedar$1,200 to $3,500$2,000 to $5,000$3,000 to $8,000
Whole house, cedar lap siding$5,000 to $16,000$7,000 to $24,000$12,000 to $40,000
Whole house, fiber cement siding$4,000 to $11,000$5,000 to $14,000$9,000 to $25,000

Labor on rot repair is the line that surprises people. A carpenter who cuts out a wet section, replaces sheathing, flashes it, and rebuilds the courses is doing far more than swapping boards, and that work bills at higher carpentry rates.

What pushes the price up?

Hidden damage, old paint, and hard-to-reach walls are the biggest price drivers, and none of them is easy to judge from the ground. That is why early quotes often change once the crew opens the wall.

Hidden sheathing and framing. Water gets behind the house wrap through failed flashing, unsealed butt joints, or splash-back at the bottom course. Replacing damaged OSB or plywood sheathing often adds $2 to $6 per square foot. Soft studs or a rotted sill plate hold up the wall, so that repair belongs to a carpenter or structural pro, not a siding crew improvising.

Lead paint. A house built before 1978 may have lead in the old paint. The EPA's Renovation, Repair and Painting rule requires certified firms to use lead-safe practices when they disturb painted surfaces in those homes. Expect containment, cleanup, and paperwork to add several hundred dollars to a couple thousand, depending on scope. Details are on the EPA lead pages.

Access. Second-story walls and gable ends usually need scaffolding or a lift, often $500 to $2,000 for the job. Plantings, decks, and tight side yards slow the crew and raise the labor line.

Matching. Older homes often have bevel, shiplap, or board-and-batten profiles that lumberyards no longer stock. Custom milling costs more, and prices climb with grade. Clear vertical-grain boards run well above knotty ones.

What lowers the bill?

Fixing the water source, limiting the scope honestly, and putting the right material in the right spot save the most. Chasing the lowest quote usually backfires.

  • Fix the cause first. A missing kickout flashing, a clogged gutter, or soil piled against the bottom course will rot new boards too. If water is running off the roof edge onto the wall, deal with that before you rebuild anything.
  • Use pre-primed boards. Back-priming and sealing cut ends before installation is cheap protection against rot.
  • Match the material to the exposure. Lower courses near the ground take the worst splash. Many contractors use rot-resistant trim-grade boards or a fiber cement product there, even on a wood wall.
  • Bundle the paint. Painting the whole elevation once costs less than painting a patch now and the wall in two years.
  • Schedule off-peak. Late fall and winter can be slower for exterior contractors in mild climates. In cold regions, paint and caulk have temperature limits, so check the product labels.

Spot repair or full re-side: how to decide

Repair when the rot is localized and has one clear cause; re-side when it shows up on several walls or the boards are failing everywhere, not just where water collects.

Spot repair fits if the rot is confined to the bottom one or two courses, a window corner, or a trim joint. It also fits if the sheathing under the damage feels solid and a moisture meter reads below roughly 19 percent on neighboring boards. Costs stay reasonable when the crew replaces boards, not structure.

Full re-siding starts to win under these conditions:

  • Rot appears on three or more walls, or across a third or more of the wall area. This is a rule of thumb, not a code number.
  • Boards are cupped, split, or shedding paint across the house, not just near the rot.
  • You can't find the original profile, so patches would look obvious.
  • You would pay for scaffolding, lead-safe containment, and a painter more than once.

For the most common situation, localized rot at the bottom courses and window corners from one fixable cause, we'd pick repairing the boards and repainting the whole elevation. It costs a fraction of a re-side and avoids mismatched paint. Patching stops paying off around the third repair visit in five years.

A full re-side is also the moment to fix the layers underneath: new house wrap, flashing, and sheathing in one pass. Check whether your jurisdiction requires a permit. Partial repairs often don't need one, but full re-sides often do. Your local building department enforces codes that are usually based on the International Code Council model codes.

DIY or hire out for wood siding repair?

Replacing a few ground-level boards is a reasonable DIY job, but structural rot, upper stories, and pre-1978 paint are where hiring out pays. Labor is most of a small repair bill, so doing it yourself can save several hundred dollars.

For a few boards you'll need a moisture meter, a flat pry bar, an oscillating multi-tool or a circular saw set to cut depth, stainless steel siding nails, primer, and paint. Wear safety glasses, gloves, and a dust mask while cutting, and work from a stable ladder. The basic sequence:

  1. Probe suspect boards with a screwdriver and mark every soft spot.
  2. Cut out the rotted boards without cutting the sheathing behind them.
  3. Check the sheathing and house wrap, and patch before covering.
  4. Prime all faces and cut edges of the new boards, then nail and caulk.
  5. Paint to match.

Turn off the circuit before cutting near an exterior outlet, light, or wiring, and leave any rewiring to a licensed electrician. If the siding turns out to be something other than wood, such as old asbestos-cement shingles, stop and have it tested before you cut.

The federal lead rule applies to paid contractors and rental housing. Owner-occupants working on their own homes are generally outside it, but the dust hazard is the same. Hire out when you find rotted studs, when the work is above one-story ladder reach, or when the house predates 1978 and you don't want to manage lead containment.

How to get quotes you can actually compare

Give every contractor the same written scope, then ask for a unit price for anything hidden. Without that, one bid might include sheathing and flashing while another quietly leaves them out.

Walk the house with each bidder and put these items in writing:

  • Exact boards or square footage to be replaced, plus board profile and species.
  • Sheathing and framing: an allowance, plus a price per sheet or per hour if more rot turns up.
  • House wrap, flashing, and kickout flashing at roof-wall intersections.
  • Primer on all faces, number of paint coats, and who supplies the paint.
  • Lead testing and lead-safe practices if the house is older than 1978.
  • Permit responsibility, debris removal, and scaffolding.

Get at least three bids and verify license and insurance. The FTC's consumer advice site has guidance on hiring contractors and avoiding large upfront payments. A bid far below the rest usually left something out.

Your next step this weekend: probe the siding with a screwdriver, take moisture readings, mark soft spots with painter's tape, and photograph them. Send those photos and the scope list above to three contractors.

Questions people ask

How much does it cost to replace one rotted siding board?

Expect roughly $100 to $400 for a single board, mostly because contractors charge a minimum visit fee and must prime, paint, and match it. The board itself often costs under $30. Bundling it with other small repairs spreads the minimum.

How much does wood rot repair cost per linear foot?

Replacing rotted trim, fascia, or rake boards typically runs about $8 to $25 per linear foot, painted. Height, board profile, and whether the crew needs scaffolding move the price. Small jobs often hit a minimum charge before the per-foot rate matters.

Can epoxy fix wood rot instead of replacing the wood?

Sometimes. Epoxy consolidant and filler can restore small, shallow rot on sills, trim, and door bottoms if the wood is mostly sound and the moisture source is fixed. DIY kits typically cost $25 to $80. Soft, crumbling, or structural wood should be cut out and replaced.

Does homeowners insurance cover rotted wood siding?

Usually not, because most policies exclude rot from long-term moisture and lack of maintenance. Damage from a sudden covered event, such as a storm or a burst pipe, may be covered. Read your policy and ask your agent before you start repairs.

Can I put new siding over rotted boards?

No. Covering rot traps moisture and lets the decay spread into sheathing and framing. Cut out the damaged material, fix the water source, and then install new siding.

Will new boards match the old paint?

Rarely on the first try. Sun-faded paint looks different from fresh paint, so painters usually repaint the full elevation or wall section, not just the patch. Budget for that when you price a partial repair.

How long does a rot repair last?

If you fix the cause of the moisture and prime every face of the new boards, the repair can last as long as the rest of the siding. If the water source is still active, new boards can rot within a few years.

Sources and further reading

Elsewhere in Remodeling