Fix and Furrow
Advertise

Adjustable Steel Support Post for Basement Beam: Buyer's Guide

Pipe size, wall thickness, and rated load at full extension matter more than finish or 'heavy duty' labels.

Save to Pinterest

We may earn a commission when you buy through links on this page. It never changes what we recommend. Learn more

Adjustable steel support post under a wood beam in an unfinished basement
Photo: Walter Martin on Unsplash

The short answer

Pick an adjustable steel post with a published load rating at your actual finished height, wall thickness listed in inches, and base and cap plates at least 4 by 4 inches (6 by 6 is better). Size it above the beam's calculated load, keep the adjustment out of its last stretch, and set it on a concrete footing, not bare slab.

Typical cost
$40 to $250 per post; $300 to $2,000 or more per post installed with a footing
Time needed
A few hours to a day per post, plus curing time for a new footing
Skill level
Advanced

Key points

  • Calculate the beam's tributary load and measure the finished post height before you compare any products.
  • A post's rated load drops as it extends, so only a rating at your actual height counts.
  • Outside diameter, wall thickness in inches, and plate size matter far more than galvanizing or 'heavy duty' labels.
  • A typical basement slab isn't built for a concentrated bearing point, so plan a concrete footing under each post.
  • Call a structural engineer if the sag is large, still growing, or tied to a moving footing or a cracked beam.
In this guide
  1. How Do You Size a Post for Your Beam?
  2. Which Type of Support Post Should You Buy?
  3. What Specs Matter on an Adjustable Steel Post?
  4. Do Galvanizing and 'Heavy Duty' Labels Matter?
  5. How Much Does an Adjustable Steel Post Cost?
  6. Can You Set the Post Right on the Slab?
  7. What's the Best Post for a 7 to 8 Foot Basement With a Sagging Beam?
  8. When Should You Call a Structural Engineer?

Write down two numbers before you shop: the load on the beam and the finished height from slab to beam. Those numbers decide which post is safe, and skipping them is where most buying mistakes start. This guide covers the common case, a sagging center beam in a basement with a 7 to 8 foot ceiling.

How Do You Size a Post for Your Beam?

Size the post to the beam's tributary load at the height where it will finally sit, so work out both before you compare products. Tributary load is the floor area that feeds one post: a strip as wide as half of each joist span on either side of the beam, times the distance between posts.

Here's an illustration, not a design. In a 24-foot-wide house, joists run 12 feet from each side wall to a center beam, so the beam collects a 12-foot-wide strip of floor. With posts 8 feet apart, each one carries about 96 square feet. At a commonly assumed 50 to 60 pounds per square foot for one finished floor, that's roughly 4,800 to 5,800 pounds. A second story or a bearing wall above can double that or more.

For height, stretch a string line along the beam between two spots where it's still level, then measure from the slab to the string at each post location. Don't measure to the sagging low point. You'll buy a post that's too short and end up running it at full extension.

Which Type of Support Post Should You Buy?

For a sagging beam in a standard basement, buy an adjustable steel post; a lally column suits a beam that has stopped moving, and a screw jack post suits heavier loads. The realistic options are below, with typical U.S. prices for the post alone, not installed.

TypeBest forAdjustable?Typical priceMain weakness
Telescoping adjustable steel postStandard 7 to 8 foot basements, correcting modest sagsYes, over a limited range$40 to $150Rated load falls as it extends; some are sold as temporary only
Screw jack postHeavier loads and fine height tuningYes, but short travel$80 to $250You must buy the right tube length up front
Lally column (concrete-filled steel pipe)Permanent support once the beam height is settledNo$60 to $200Must be cut to exact length; heavy to handle
Sistered or replaced beamA cracked, rotted, or overstressed beamNot applicableVaries widelyFixes the beam, not the support points

If the beam has stopped moving and you can measure the height to a quarter inch, a concrete-filled lally column is a sturdy permanent choice. If you're lifting a sag or can't measure that precisely, the adjustable post wins because you can fine-tune it.

The terms overlap. Many sellers call any post with a threaded top a screw jack post, so read the spec sheet rather than the name.

What Specs Matter on an Adjustable Steel Post?

Four specs carry the real weight: outside diameter, wall thickness, rated load at your extended height, and plate size.

Outside diameter. A '3-inch' post might measure 3 inches across, or it might be 3-inch nominal pipe, which measures 3.5 inches outside. Read the actual number. The International Residential Code, published by the International Code Council, generally calls for steel columns of at least 3-inch standard-weight pipe or an approved equivalent. Local adoption and amendments vary, so confirm with your building department.

Wall thickness. Many telescoping posts use thinner walls than standard-weight pipe. Look for the thickness in inches on the spec sheet. A product that only says 'heavy duty' is hiding the number you need.

Rated load at full extension. This is the spec that sinks people. A slender steel tube buckles more easily the longer it gets, so the rating at maximum extension is lower than the headline number on the box. Look for a load chart that lists capacity by height. If the label prints one number, assume it's the best case at the shortest length.

Plates. Base and cap plates commonly start at 4 by 4 inches, and 6 by 6 spreads the load better into the beam and the concrete. The cap plate should bear on the beam's full width and have holes for fasteners.

Check whether the post is labeled for permanent use, because many adjustable posts are sold as temporary shoring. An ICC-ES evaluation report, where one exists, can make approval easier, though acceptance is the inspector's call.

Do Galvanizing and 'Heavy Duty' Labels Matter?

Not much. Galvanizing, 'heavy duty' labels, and tonnage printed on the box add little to what the post can safely carry. Galvanizing resists rust, which helps in a basement that stays damp, but it does nothing for buckling strength. In a dry basement, a coat of rust-inhibiting primer and paint does the same job.

Pin-style and screw-style adjustment both work if the post is rated for your height and the pin or thread is seated properly. Pre-drilled holes and factory-attached plates are conveniences, not strength features.

How Much Does an Adjustable Steel Post Cost?

The post itself usually runs $40 to $250, and the job climbs to $300 to $2,000 or more per post once labor and a new footing are involved. Region, length, and whether the product has documented ratings move the price.

TierTypical priceWhat drives it
Basic telescoping post$40 to $90Thin wall, small plates, often a temporary-use rating
Mid-range rated post$90 to $150Larger diameter, load chart, bigger plates
Heavy-wall or screw jack post$150 to $250Thicker wall, higher ratings, documented testing
Installed by a contractor$300 to $800 per postLabor, hauling, permit time
Installed with new concrete footing$800 to $2,000 or moreSlab cutting, excavation, concrete, soil conditions

Once labor and a footing are in the picture, the post is the smallest line item. Spending an extra $50 to $100 on a better-rated one is cheap next to a repair later.

Can You Set the Post Right on the Slab?

Usually not. A typical basement slab, often about 4 inches thick and lightly reinforced at best, isn't built for a concentrated bearing point, so a loaded post can punch through or settle and bring the sag right back.

The usual fix is a concrete footing poured below the slab. Pads commonly run somewhere around 2 feet square and 12 inches thick, but the load and soil set the real size, and your building department or engineer makes the call. Anchor the base plate to the footing with concrete anchors, and fasten the cap plate to the beam as the manufacturer directs. Codes also typically require the bottom of a fixed column to be restrained against sliding.

Cutting a slab throws off silica dust, so use a wet saw or other dust control, plus a respirator rated for silica, eye protection, and hearing protection. Before you cut, locate drain lines, radon pipes, and any in-floor heat tubing. Calling 811 covers buried utilities outside, not what's under your floor. In an older house, test suspect pipe wrap or old floor tile for asbestos before you disturb it.

A new footing and structural change usually need a permit, and many jurisdictions inspect the excavation before you pour. Ask first.

If the old post sat on bare slab and the beam still sagged, suspect the slab first.

What's the Best Post for a 7 to 8 Foot Basement With a Sagging Beam?

We'd pick a rated adjustable steel post with an outside diameter of at least 3 inches (3.5 where you can find it), wall thickness published in inches, a load chart that covers your height, a permanent-use label, and 6 by 6 inch plates. A larger diameter resists buckling better at the same length and usually costs little extra.

Choose a length so your finished height lands in the middle of the adjustment range, never at the stop. Pick a rating comfortably above your calculated load, because your estimate is rough and the post carries it for decades. Give each post its own concrete footing, and raise the beam gradually over several weeks.

If the beam only needs to be held where it is, not lifted, and you can measure precisely, a concrete-filled lally column is a fine alternative.

When Should You Call a Structural Engineer?

Call a structural engineer if the sag is an inch or more, is still growing, or comes with a cracked or rotted beam, a moving footing, or cracks in the foundation wall. A site visit and letter often runs from a few hundred dollars to over $1,000 depending on region, and it gives you a post size, spacing, and footing design to hand an inspector.

Replacing a post that's already carrying load means shoring the beam temporarily first. If you haven't done that before, hire a licensed contractor.

Stair-step cracks, bowing walls, and sticking doors point to problems a post won't solve. Read about foundation crack repair mistakes that make patches fail before you patch anything, and if the footing itself is sinking, see helical piers vs push piers for the heavier fixes.

Your next step: string-line the beam, measure slab to beam at each post, sketch the joist spans, and call your building department about permits and footing requirements before you buy anything.

Questions people ask

Can an adjustable steel post be used as a permanent support?

Some can, but many are sold as temporary shoring only. Look for permanent-use language on the label and an ICC-ES evaluation report, and ask your local building department what it accepts.

How far apart should basement support posts be?

Spacing is often somewhere between 6 and 10 feet, but the beam's size, material, and load set the real limit. Closer spacing means each post carries less, though every added post needs its own footing.

How much weight can a 3-inch adjustable steel post hold?

Published ratings vary widely with wall thickness, diameter, and extended height, and a lightly built post may carry only a few thousand pounds at full extension. Look for a capacity chart at your height rather than a single headline number.

Do adjustable steel posts rust in a damp basement?

Yes, bare or painted steel will rust where moisture is persistent. Galvanized posts last longer in damp conditions, but fix the moisture source too, since standing water at the base plate will corrode any finish.

Can I move or remove an existing basement post?

Not without an engineer's input. Removing or relocating a post lengthens the beam's span and shifts load onto the remaining posts and footings, which can cause new sagging or damage.

Sources and further reading

Elsewhere in Remodeling