Part of our Roofing and Exterior guide
How to Replace Damaged Asphalt Shingles Without a Leak
A single-shingle repair takes about an hour per spot, but nail placement and sealing decide whether it holds through winter.
Save to PinterestWe may earn a commission when you buy through links on this page. It never changes what we recommend. Learn more
The short answer
Break the seal on the course above, pull the nails with a flat pry bar, slide the damaged shingle out, and slide a matching one in. Drive nails in the manufacturer's marked nail zone (usually four), then hand-seal the tabs with asphalt roofing cement. Follow the wrapper and warranty instructions, and stop if the deck is soft.
- Typical cost
- $40 to $200 in materials, depending on tools you own; $200 to $600 if a roofer does it
- Time needed
- 1 to 3 hours for a few shingles
- Skill level
- Intermediate
Key points
- Replacing a few shingles doesn't automatically void a warranty, but ignoring the manufacturer's nailing and sealing instructions can give them grounds to deny a claim.
- Nails go only in the marked nail zone, never through the exposed face and never high on the shingle, or you weaken the wind resistance.
- In cool fall weather, hand-seal every repaired tab with quarter-sized dabs of asphalt roofing cement, because factory sealant strips may not bond in the cold.
- If the deck feels soft, the shingles crumble, or damage covers more than a few tabs in one area, stop and call a licensed roofer.
In this guide
- Can you replace a few damaged shingles yourself?
- What tools and materials do you need?
- How do you find a matching shingle and keep the wind rating?
- How do you remove a damaged shingle without tearing its neighbors?
- Where do the nails go on the new shingle?
- How do you seal the repair so it holds through winter?
- What mistakes turn a small shingle repair into a leak?
- When should you stop and call a roofer?
You can swap a few damaged shingles in about an hour per spot if the slope is walkable, the deck underneath is solid, and the neighboring shingles are still flexible. Replacing shingles doesn't automatically void a warranty. A repair that ignores the manufacturer's instructions does give them room to deny a claim: wrong nails, high nailing, a mismatched product, or skipped sealing. Read your warranty paperwork first, since terms vary by manufacturer and roof age.
Can you replace a few damaged shingles yourself?
Yes, if the damage is limited to a few shingles, the roof pitch is walkable, and the wood under the shingles is sound. Creased, cracked, or missing shingles after a windstorm are the classic candidates.
Hand the job to a pro if any of these show up:
- The slope is steeper than about 6-in-12 (6 inches of rise per 12 inches of run), and you don't own a fall-arrest system and know how to anchor it.
- Shingles are curling, shedding granules in patches, or cracking when you flex them. That's age, not storm damage, and patching won't fix it.
- The deck feels spongy underfoot, or you see dark staining in the attic.
- The damage sits near a chimney, skylight, valley, or vent. Flashing work belongs to a roofer.
- The roof is old enough that it may contain asbestos-containing materials. Don't cut or break anything until it's been tested.
What tools and materials do you need?
You need a few basic roofing tools and a matching bundle of shingles, which runs roughly $90 to $200 if you're starting from scratch. Put everything on the roof before you start so you aren't climbing up and down.
| Item | What it's for | Typical cost |
|---|---|---|
| Flat pry bar | Pulling nails and lifting tabs | $10 to $25 |
| Roofing hammer or coil nailer | Driving nails flush | $25 to $45 for a hammer |
| Utility knife with hook blades | Trimming and cutting shingles | $8 to $20 |
| Putty knife | Breaking seals gently | $5 to $10 |
| Galvanized roofing nails | Fastening the new shingle | $5 to $12 per pound |
| Asphalt roofing cement, caulk-gun tube | Hand-sealing tabs | $8 to $15 |
| Replacement shingles | The repair itself | $30 to $70 per shingle bundle |
Add soft-soled boots, gloves, and safety glasses, plus a fall-arrest system with a rope grab if the pitch calls for one. Use corrosion-resistant roofing nails with a head about 3/8 inch across, long enough to go through the shingle and bite into the deck. The wrapper will say what length it wants. Drywall screws, finish nails, and deck screws don't qualify.
How do you find a matching shingle and keep the wind rating?
Match the shingle by type, thickness, and color, and keep the original wind rating by following the nailing pattern printed on the new bundle's wrapper. Check the garage or attic first for leftover bundles from the original install, since the wrapper often carries the product name.
If there are no leftovers, take a broken piece to a roofing supply house. Two broad families dominate: flat 3-tab shingles with three cutouts per strip, and thicker architectural shingles with a layered, dimensional look. Don't swap one for the other. The thickness difference makes a visible bump and changes how the course above lies.
Color won't match perfectly on a roof that's weathered for years. Pick the closest one, and if you have a choice, put it where it's least visible from the street. Some manufacturers' warranties ask that repairs use their own products, so check the wording. The National Roofing Contractors Association (NRCA) publishes technical guidance for roofing contractors, which is useful if you want to see how professionals approach repairs.
How do you remove a damaged shingle without tearing its neighbors?
Break the seal on the shingles above, lift them just enough to reach the nails, pull those nails with a flat pry bar, and slide the damaged shingle out. Slow, gentle prying is the whole technique.
- Pick a warm part of the day. Shingles get brittle below roughly 40°F. In cool weather, wait until the sun has warmed the roof, usually late morning to mid-afternoon.
- Break the seal. Slide a putty knife under the tabs of the course above the damaged shingle and work it side to side to separate the factory sealant strip. Don't yank. A torn granule layer is a future leak.
- Lift the course above. Raise the tabs just enough to see the nails, a few inches at most. Bending shingles sharply creates a crease.
- Find the nails. Four nails typically hold the damaged shingle, hidden under the course above. Nails from that upper course may also run through the damaged one. Slide the pry bar underneath and feel for each head.
- Pull the nails. Set the flat end of the flat pry bar under each nail head and work it out. Don't hammer them down, because a nail left in place will wear through the new shingle. Note which upper-course shingles lost nails.
- Slide the old shingle out. If it resists, there's still a nail somewhere. Stop and look instead of forcing it.
Check the underlayment and deck while it's open. Dry, intact underlayment means you can proceed. A damp or rotted spot means the problem is bigger than one shingle.
Where do the nails go on the new shingle?
Nails go in the manufacturer's marked nail zone, typically four per shingle on a standard install and six where the wrapper calls for a higher wind rating. The exact pattern differs by product, so read the wrapper.
Slide the new shingle into place so its bottom edge matches the course line and its exposed portion matches its neighbors. Then drive nails through the marked strip, not above it and not through the exposed surface. On architectural shingles the nail zone is a visible band across the reinforced area. On 3-tab shingles, nails typically sit just above the cutouts and a little in from each edge, per the wrapper's diagram. Once the new shingle is in, re-nail any upper-course shingle whose nails you pulled, and dab cement over exposed nail heads.
Drive each nail flush and straight. An overdriven nail punches through the mat. An underdriven one pokes up through the shingle above. Both fail in a windstorm. A roofing hammer with a smooth face makes it easier to feel the nail seat, and a nail gun set too high tends to overdrive, so test on scrap first.
High nailing is the most common error. A nail set an inch or two above the zone misses the reinforced overlap, and the shingle can blow off in moderate wind. A manufacturer can also point to it if you file a claim later.
How do you seal the repair so it holds through winter?
Hand-seal the new shingle and the tabs you lifted with asphalt roofing cement, because factory sealant strips need sustained warmth and sun to bond and cool fall days often can't deliver either.
Use a caulk gun to place quarter-sized dabs of asphalt roofing cement, about 1 inch across, under the tabs of the new shingle. Check the wrapper for how many dabs the manufacturer specifies, since the count varies by product. Press each tab down firmly for a few seconds. Do the same under every tab you lifted above, wherever the original sealant strip was broken.
Go light. A thick glob of cement creates a bulge and traps water. Small dabs hold well and let the shingle lie flat.
Check your work afterward. From the ground, look for tabs that stand up or ripple. From the attic, look at the underside of the deck near the repair after the next rain. Fresh dampness, a dark stain, or daylight at the nail line means something is off.
What mistakes turn a small shingle repair into a leak?
The mistakes that most often cause leaks are nailing too high, driving nails through the exposed face, leaving old nails behind, and skipping the hand-sealing in cold weather. Fasteners that aren't corrosion-resistant belong on the list too, since they rust and back out.
Patching over a cracked shingle with a smear of cement is the other classic. It might hold for a season, but the shingle underneath is still failing. And lifting cold, brittle tabs without warming them or going slowly cracks the course above, which just moves the leak up the roof.
When should you stop and call a roofer?
Call a licensed roofer when the damage reaches flashing, the deck is soft, the pitch is too steep to work safely, or more than a few shingles in one area are damaged. A professional small repair typically runs $200 to $600, depending on roof height, access, and local minimums, and that's cheaper than replacing a rotted deck later.
Call one too if you're filing a storm claim. Many insurers want documentation of the damage before repairs, and a written estimate helps. For hiring tips and contractor red flags, the FTC's consumer advice pages are a good starting point.
Check permits before you start. Many jurisdictions don't require one for minor repairs, but some do. Most U.S. local codes build on model codes published by the International Code Council, with local amendments, including wind provisions in some regions. Your building department can tell you what applies where you live.
Your next step: walk the roof perimeter from the ground with binoculars this week, mark the damaged spots, and pick a warm, dry day in the next couple of weeks to do the repair before the first hard freeze.
Questions people ask
Will my homeowners insurance pay for storm-damaged shingles?
It depends on your policy, your deductible, and the cause of the damage. For a few shingles, the repair cost may fall below your deductible. Get a written estimate, call your insurer before starting work, and keep photos of the damage.
Can I just glue down a lifted or curled shingle instead of replacing it?
If the shingle is intact and flexible, yes. Dab asphalt roofing cement under the tab and press it down. If it's cracked, torn, or shedding granules, replace it.
What if I can't find an exact color match?
That's common on older roofs. Pick the closest match from the same product line if you can identify it, and place the new shingle where it's least visible. The color will weather closer over a few seasons.
How many shingles can I replace before it's a roofer's job?
There's no hard number. Damage spread across a slope, or more than a few shingles in one area, usually points to wind or age problems that a patch won't solve. Get a roofer's opinion before piling on repairs.
How old is too old to patch a shingle roof?
There's no single age cutoff, since lifespan varies with shingle type, climate, and attic ventilation. The better test is condition. If shingles are curling, cracking when flexed, or losing granules across whole slopes, replacement will serve you better than patching.
Sources and further reading
- National Roofing Contractors Association Technical guidance for roofing contractors and help finding qualified roofers
- International Code Council Model building codes that local jurisdictions adopt for roofing work
- FTC Consumer Advice Consumer advice on hiring contractors and avoiding repair scams
Was this article helpful?