Fix and Furrow
Advertise

Pool Liner Replacement Cost: Liner, Labor, and Extras

Separate the liner from the labor, then watch for the draining, disposal, and wall-repair line items that split bids by thousands.

Save to Pinterest

We may earn a commission when you buy through links on this page. It never changes what we recommend. Learn more

Empty in-ground pool with a new blue vinyl liner being smoothed into place
Photo: Jason Gooljar on Unsplash

The short answer

Pool liner replacement for a typical in-ground vinyl pool costs about $3,500 to $8,000 installed. The liner itself runs roughly $900 to $2,500 and labor adds $1,500 to $4,500. Freeform pools with benches, or pools with rusted walls, can top $10,000. Doing the demolition yourself trims the bill, but wall damage hidden under the old liner can erase the savings.

Typical cost
$3,500 to $8,000 installed for a typical pool; $5,500 to $10,000+ for freeform
Time needed
1 to 2 days on site, plus 2 to 4 weeks for a custom liner order
Skill level
Hire a pro

Key points

  • A typical turnkey vinyl liner replacement runs $3,500 to $8,000, with the liner itself roughly a quarter to 40 percent of that.
  • Freeform shapes, deep ends, extra steps, and wall damage move the price more than pool size alone.
  • Draining, disposal, base repair, wall repair, refill, and chemicals can total $1,000 to $5,000 or more, depending on what a bid bundles, so compare bids line by line.
  • A liner that is 10 to 15 years old and leaking in more than one spot is usually worth replacing rather than patching.
  • DIY saves labor but is unforgiving: a wrinkled or misfit liner can't be fixed once the pool is full.
In this guide
  1. What does a vinyl pool liner replacement cost?
  2. Materials vs labor: where does the money go?
  3. What pushes the price up: shape, depth, steps, and wall condition?
  4. What pulls the price down: pattern, timing, and bid scope?
  5. Repair or replace? Signs the liner is done
  6. DIY liner install vs hiring a pool contractor
  7. How do you get comparable bids and avoid hidden charges?

A standard in-ground pool lands between $3,500 and $8,000 for a turnkey vinyl pool liner swap, and the liner is the smaller part of the bill. The rest is crew time, draining, disposal, and whatever the crew finds under the old liner. These are typical U.S. ranges. Your region, pool shape, and wall condition decide where you fall.

What does a vinyl pool liner replacement cost?

Most homeowners pay $3,500 to $8,000 for pool liner replacement, installed, with small rectangles at the low end and freeform pools with steps and benches at the high end. The table breaks that down by size and shape.

Pool typeLiner onlyInstall laborTypical turnkey total
Small rectangle (12x24)$600 to $1,300$1,500 to $2,500$2,800 to $4,800
Mid-size rectangle (16x32)$900 to $1,900$1,800 to $3,200$3,500 to $6,500
Large rectangle (18x36)$1,200 to $2,500$2,200 to $3,800$4,500 to $8,000
Freeform or kidney (16x32) with bench and steps$1,500 to $3,500$2,500 to $4,500$5,500 to $10,000+

Totals assume removal, disposal, a refill, and routine base touch-ups. They leave out major wall repair, covered below. Metro and coastal markets run higher, and contractors often quote more in peak season than in a slow one.

Materials vs labor: where does the money go?

Labor and extras make up most of a turnkey bid, with the liner itself usually running a quarter to 40 percent of the total. Liner price depends on size, wall depth, thickness (20 mil is common, and 27 to 30 mil typically costs more), and whether the pattern is stock or exclusive. Many warranties are prorated and focus on seams and fading, so read what is actually covered.

A crew of two to four typically needs one to two days. They drain the pool, pull the old vinyl, smooth the base, set the track, hang the liner, and pull it tight with a vacuum before refilling. Extras are where bids diverge, because some contractors bundle them and others itemize:

Line itemTypical range
Draining and refilling water$50 to $500 (water rates and gallons)
Old liner removal and disposal$100 to $400
Base repair (patching low spots, new sand or vermiculite)$300 to $1,500
Wall repair, rust treatment, or panel replacement$500 to $3,000+
New gaskets, faceplates, and fittings$50 to $300
Startup chemicals and water balance$100 to $400

A bid that bundles these items and one that leaves them out can sit $2,000 or more apart for the identical pool, with nobody padding anything.

What pushes the price up: shape, depth, steps, and wall condition?

Freeform shapes, deep ends, extra steps, and damaged walls raise the price the most, often more than square footage does. Rectangles frequently come in near-stock sizes. A freeform or kidney pool needs a liner made from measurements taken at the pool, which takes weeks and costs more. Let the installer take those measurements, because a bad one is expensive and the liner can't be returned once it's cut to your numbers.

Depth matters too. A pool running from 3.5 feet to 8 feet needs more vinyl, and deep-end slopes and hoppers are harder to hang without wrinkles. Liner-wrapped steps and corner benches add cutting, fitting, and labor time.

Walls are the biggest unknown in any bid, because nobody sees them until the old liner is out. Rust on steel pool walls, cracked or shifted polymer wall panels, and rough masonry all need work before a new liner goes in. Get a written per-panel or hourly price before work begins. Structural wall repair may also need a permit in your area, so check with your local building department.

What pulls the price down: pattern, timing, and bid scope?

A stock pattern, standard thickness, off-peak scheduling, and a tightly scoped bid are the main ways to cut the price without gambling on quality. Stock patterns can cost a bit less than exclusive prints, though the gap varies by manufacturer and pool size.

Timing matters more than most people expect. Spring is the busy season, and vinyl gets stiff in cold weather, so installers prefer warm days. Warm-climate pools can often be done off-season, while colder regions can measure and order in fall for an early spring install, ahead of the rush.

Scope is the third lever. If you drain the pool and haul out the old liner yourself, some crews will take a few hundred dollars off. Just don't skip the wall and base inspection on the way.

Repair or replace? Signs the liner is done

Replace the liner if it's brittle, faded, wrinkled, or leaking in more than one spot; patch it only if it's still supple and has a single puncture. A liner typically lasts roughly 10 to 15 years, and sometimes longer with steady water chemistry and a winter pool cover that fits.

Run a bucket test first to confirm a leak and not evaporation. Set a bucket of pool water on a step, mark the level inside the bucket and on the pool wall, and check both after 24 hours. If the pool drops noticeably more than the bucket, or keeps dropping with the pump off, something is leaking. A pool liner patch kit costs roughly $10 to $30 and handles small punctures you can reach underwater. A professional patch call typically runs $100 to $400.

We'd replace a leaking liner that's 10 to 15 years old. Aged vinyl loses elasticity, so a patched leak often reappears somewhere else, and you keep paying for water and chemicals. A steady leak also soaks the base and speeds rust on steel walls, which can turn a routine job into a major repair. Patch only if you're selling soon or the liner is supple and the damage is isolated.

Other signs it's finished: fading that exposes the pattern's white base, stretched sections pulling away from the track, wrinkles that won't relax, and staining or odor behind the liner.

DIY liner install vs hiring a pool contractor

Hire a pool contractor for most liner jobs; DIY can save roughly $1,500 to $4,500 in labor, but mistakes only show once the water is in. A wrinkle or off-center liner can't be fixed without draining again, and wrong measurements are worse.

The job runs in order: drain, remove the old liner, repair walls and base, set the track, hang the liner, pull it tight against the walls with a wet/dry vacuum, then refill and cut in fittings as the water rises. You need three or four helpers, a warm day, and patience for smoothing a vermiculite base or sand floor. Plug the vacuum into a GFCI-protected outlet, and stay out of an empty pool when surfaces are wet, since vinyl and walls get slick. Check the liner maker's warranty first, because some require professional installation.

Use a pool contractor for any freeform pool, any pool with a deep-end hopper, or any pool with visible wall damage. A reasonable middle path is to buy the liner and do the demolition yourself while the contractor handles the hang and fill. Experienced DIYers with a simple rectangle and sound walls can tackle the whole thing.

While the pool is empty, inspect the main drain cover and fittings. Pool Safely explains drain entrapment risks and what compliant covers look like.

How do you get comparable bids and avoid hidden charges?

Get at least three written bids that list the same scope line by line, because the bottom-line number hides the differences. Ask each contractor to confirm:

  • Who measures, and who pays if the liner doesn't fit
  • Liner thickness, pattern, and warranty terms in writing
  • Whether removal and disposal of the old vinyl is included
  • How the water is handled: draining, refill, and any hauled-in water
  • The base type and what happens if the floor needs repair
  • A per-panel or hourly wall repair price
  • New gaskets, faceplates, and a startup chemical package

A low bid that leaves out three of those items isn't low.

Your next step this week: run the bucket test, then call three contractors to schedule a measurement and wall inspection. In a cold climate, aim to have your order placed by winter.

Questions people ask

How long does a pool liner replacement take?

Most crews finish the install in one to two days once the liner is on site. Add two to four weeks for a custom liner order. Refilling often takes a day or more on top, and wall or base repairs can stretch the schedule.

Does homeowners insurance cover a pool liner replacement?

Usually not. Wear, age, and gradual leaks are typically excluded, though sudden damage from a covered event may be treated differently. Check your policy or ask your agent before filing.

Can I reuse my pool water when I change the liner?

Sometimes, if the water is clean and you have somewhere to store it, but most people drain and refill. Chemically treated water may be restricted from discharge in some areas, so check local rules before draining.

Is a thicker liner worth the extra money?

A 27 to 30 mil liner costs more and tends to resist punctures better than a 20 mil one. It won't fix poor water chemistry or a bad base, which cause many early failures. It's a reasonable upgrade for pools with kids, pets, or rough use.

Can I install a new liner over the old one?

No. The old liner has to come out so the base and walls can be inspected and repaired, and a layered liner would telegraph every bump and fold. Liner installation instructions generally call for removing the old one.

Sources and further reading

Elsewhere in Pools & Yard Decor