Part of our Home Repair Troubleshooting guide
Snow Blower Won't Start After Sitting? Start With the Gas
Stale gas and a gummed carburetor are the usual suspects after months in storage, and a few cheap tests tell you which.
Save to PinterestWe may earn a commission when you buy through links on this page. It never changes what we recommend. Learn more
The short answer
A snow blower that won't start after sitting most often has stale gas or a gummed carburetor. Drain the old fuel, refill with fresh 87-octane gas, then confirm spark with an inexpensive inline tester, check the plug, and use full choke with two or three primer pushes. If it still won't run after one carburetor cleaning, take it to a small-engine shop.
- Typical cost
- Roughly $10 to $50 in gas and parts for DIY; $100 to $250 at a shop for carburetor service
- Time needed
- 1 to 3 hours, plus drying time if the engine is flooded
- Skill level
- Intermediate
Key points
- Gas that has sat for many months, especially an ethanol blend, is the most common reason a snow blower won't start after storage.
- Test for spark before cleaning anything, so you don't rebuild a carburetor on a machine with an ignition problem.
- A spark plug costs only a few dollars, so replace it even if it looks passable.
- On a cold engine, use full choke and two or three primer pushes; more than that floods it.
- If one carburetor cleaning doesn't fix it, a small-engine shop usually beats a second round of guessing.
In this guide
Start with the gas. If the fuel in the tank has been there since last winter, it is the likeliest culprit, and replacing it costs less than anything else on this list.
Why won't a snow blower start after sitting?
After months in storage, the usual cause is gas that has gone stale and left varnish in the carburetor.
Ethanol-blend gasoline absorbs moisture and starts to break down within a few months. It leaves a sticky film that clogs the tiny jets in the carburetor, which meter fuel into the engine. Spark problems come second, then a fouled plug, then choke and primer errors. Check in that sequence and you rarely waste an afternoon.
First, run the basics. The key or safety switch should be in, the engine switch set to run, the fuel valve open if your model has a fuel shutoff valve, and the oil at the proper level. Many models have a low-oil sensor that kills the ignition.
| Step | Quick test | Typical fix |
|---|---|---|
| 1. Fuel | Smell it, look for dark color or a varnish film | Drain and refill with fresh gas |
| 2. Spark | Inline spark tester on the plug wire | New plug, or a shop for a bad coil |
| 3. Plug | Pull it and read the tip | Clean, regap, or replace |
| 4. Choke and primer | Watch the choke plate, check the primer bulb | Correct the sequence or replace the bulb |
| 5. Carburetor | Short shot of starting fluid in the intake | Clean with carburetor cleaner, or rebuild |
Should I check the fuel first?
Yes, check the fuel first, because old gas is the most common cause and the easiest to confirm.
Open the cap and look. Fresh gas is clear to pale yellow and smells sharp. Gas that is dark, cloudy, or smells sour is finished. Drain the tank outdoors into an approved fuel container, using the drain bolt on the carburetor bowl or a siphon. Take the old gas to a household hazardous waste site; don't put it in the trash or down a drain.
Refill with fresh 87-octane gas, and check your manual for the ethanol limit, which is commonly 10 percent. Don't pour new gas on top of old, because the old stuff carries the problem along. If your carburetor bowl has a drain screw, open it over a pan and let a few ounces out to flush the bowl.
How do I test for spark?
Use an inline spark tester, a low-cost tool that sits between the plug wire and the plug and flashes when the ignition fires.
Connect it, then pull the cord. A steady blue flash means the ignition is working. No flash, or a weak orange one, points to a bad plug, a loose wire, a failed coil, or a stuck safety switch. Do this before touching the carburetor.
Keep the test away from spilled fuel and fuel vapor. Don't pull the cord with a bare plug resting near the open plug hole, because the spark can ignite vapor from the cylinder.
What should the spark plug look like?
A healthy spark plug has a light tan tip, dry and clean, with an unbroken white porcelain insulator.
Remove it with a spark plug socket. Black and sooty means the mixture was too rich or the choke was left on. Wet and smelling of gas means flooding. A cracked insulator or a rounded, worn electrode means replace it. The gap is often around 0.025 to 0.030 inches, but it varies by engine, so check your manual.
We'd replace it regardless. A plug costs a few dollars, and one that's marginal after a long sit can mimic a carburetor fault. If the old one was wet, pull the cord several times with the plug out and the choke off to clear the cylinder before you install the new one.
Are my choke and primer set correctly?
A cold engine needs full choke and two or three pushes of the primer bulb, not ten.
Over-priming is how people flood an engine that was fine. Press the bulb and watch it. One that stays flat, feels hard, or is cracked can't push fuel and needs replacing, usually a inexpensive part. Also look at the clear fuel line. If no gas moves when you press, the line or a clogged inlet is blocking it.
To start cold, set the choke to full, prime, and pull. Once the engine catches, move the choke to half, then off, over about 30 seconds. An engine that fires and dies the moment you open the choke is starved for fuel. That leads to the next check.
When should I clean or rebuild the carburetor?
Clean the carburetor when fresh gas, good spark, and a clean plug still leave you with an engine that won't run.
For a quick confirmation, spray a one-second shot of starting fluid into the air intake and pull the cord. If it fires briefly and dies, the problem points to fuel delivery. Start by spraying carburetor cleaner into the intake and around the linkage. If that fails, remove the carburetor bowl, clean the main jet with cleaner and compressed air, and reassemble with a new bowl gasket.
Don't poke jets with wire. It enlarges them and ruins the fuel mix. If the float sticks, the needle valve is gummed, or the passages stay clogged, a rebuild kit for a basic carburetor typically runs $10 to $30. On many common engines, a replacement carburetor can cost less than an hour or two of shop labor, so price both before you commit.
When should I take it to a small-engine shop?
Take it in when it still won't run after fresh gas, a new plug, confirmed spark, and one proper carburetor cleaning.
Other signs include no spark with a good plug, a pull cord that's stuck or won't turn the engine, metal noises, milky oil, or a recoil that kicks back hard. Electrical and internal engine faults are better left to a technician. A shop usually charges roughly $100 to $250 for carburetor service, plus pickup or delivery fees that vary by area. Shops tend to back up after the first heavy snow, so book early rather than the day of the storm.
Your next step: drain the tank today, then run the spark test before the forecast changes.
Questions people ask
How long does gas last in a snow blower?
Untreated gas with ethanol can begin to degrade within a few months, and after a full off-season it's often unreliable. Gas with a stabilizer in a full, sealed tank lasts longer, but fresh gas is still the safest bet.
Why does my snow blower start and then die?
That's usually a partly clogged carburetor jet that lets the engine run only on the choke's richer mix. Clean the carburetor, and check that the fuel cap vent isn't blocked.
Is it safe to use starting fluid in a snow blower?
A brief spray into the intake is a common diagnostic test, but it's highly flammable and shouldn't be used repeatedly. Use it sparingly, away from sparks, and don't rely on it to run the engine.
Does the electric starter matter if the engine cranks fine?
If the engine turns over, the starter is working and the problem is fuel, spark, or air. Check the extension cord and outlet only if the starter does nothing at all.
What if the pull cord won't pull?
Don't force it. Remove the spark plug wire and try again; if the cord is still locked, something is jammed or the engine may have seized. At that point, a small-engine technician should take a look.
Sources and further reading
- Cooperative Extension (extension.org) Find your state extension office for local small-engine and fuel storage advice
- USDA Plant Hardiness Zone Map Look up your zone to gauge how long your winter season runs
Was this article helpful?