Fix and Furrow
Advertise

Snow Blower Maintenance Before First Snow: A Timed Checklist

Oil and plug are the easy part. The shear pins, skid shoes, and fuel decisions decide whether it starts and throws in a storm.

Save to Pinterest

We may earn a commission when you buy through links on this page. It never changes what we recommend. Learn more

Man operating a gas snow thrower blowing snow across a residential street
Photo: Victor Figueroa on Unsplash

The short answer

Start about four weeks before snow is likely. Change the oil and spark plug, check shear pins, belts, and the friction disc, set scraper and skid shoe clearance, and replace old gas with fresh, stabilized fuel. If snow is a week out, do the fuel, shear pins, and a test run first.

Typical cost
$30 to $100 in basic parts for a DIY tune-up; often $100 to $250 at a shop
Time needed
2 to 4 hours of hands-on work, spread over a few sessions
Skill level
Beginner

Key points

  • If time is short, check the shear pins and the fuel first; they're the quickest checks and the ones most likely to save you in a first storm.
  • Gas left in the tank since spring should be drained and replaced, not topped off.
  • Buy a spare pack of manufacturer-spec shear pins and keep two by the machine.
  • Set scraper and skid shoe height for your driveway surface: about 1/8 inch on pavement, an inch or more on gravel, then confirm against your manual.
  • Cold-winter areas should finish by early November; mild-winter areas can wait until late November or December.
In this guide
  1. When should I start snow blower maintenance before the first snow?
  2. Oil and spark plug: what do I change first?
  3. Shear pins, belts, and friction discs: what fails mid-storm?
  4. How do I set the scraper blade and skid shoe clearance?
  5. What should I do with old gas and fuel stabilizer?
  6. What's the schedule for cold and mild climates?
  7. What does a good test run look like?

If you only have one day, check the shear pins and the fuel. Those two tell you most of what you need to know about a machine that's been sitting since spring, and they're what strand people in the first storm. This snow blower pre-season checklist runs in a set order, because some jobs need parts you have to buy first.

When should I start snow blower maintenance before the first snow?

Start about four weeks before snow is likely, which in much of the northern U.S. means late September or early October. That window leaves time to order a belt or scraper blade, the parts that run short once a forecast hits. If you're already inside four weeks, squeeze the work into one weekend and do the fuel, shear pins, and a test run first.

The USDA Plant Hardiness Zone Map shows average coldest winter temperatures, not snowfall, so treat it as a rough guide at best. Your area's usual first-snow date is the better trigger. In this guide, "cold-winter" means snow is normal by early to mid November, and "mild-winter" means it's late November, December, or occasional.

Oil and spark plug: what do I change first?

Change the oil and the spark plug first, because they're cheap, quick, and a common fix for a hard-starting machine. For a snow blower oil change, run the engine for a minute so the oil flows, then drain it into a pan. Four-stroke snow blower engines usually hold somewhere between a pint and a quart, but your manual has the exact amount.

Grade matters in a machine that has to start at 10 degrees. Many manuals call for 5W-30, and some specify synthetic for very cold starts. Follow the chart in yours. Expect $8 to $25 for oil, changed at least once a season or at the hour interval the manual gives.

A new spark plug costs roughly $5 to $15. Match the plug number and gap to the manual, and snug it down without cranking on it. A plug with a black, oily, or worn electrode is done. Even a clean one is cheap enough to swap yearly.

Shear pins, belts, and friction discs: what fails mid-storm?

Shear pins, drive and auger belts, and the friction disc are the parts to check, and the shear pin is the one designed to fail. It's a deliberately weak bolt that snaps when the auger hits ice or a buried rock, so the gearbox doesn't take the blow. Two-stage machines have them on the auger shaft. Look for bent, rusted, or loose pins, and grease the shaft as the manual directs so the augers spin freely by hand.

Buy a spare pack, which usually costs a few dollars, and keep two with the clearing tool. Use the exact pin the manufacturer specifies. A stronger hardware-store bolt means the gearbox takes the hit instead, and that repair can be costly. Single-stage machines generally don't have shear pins; the rubber paddles absorb the impact.

Next, inspect the drive belt and auger belt for cracks, glazing, or fraying. Belts typically run $15 to $40 each. On many two-stage machines a rubber friction disc drives the wheels, and a hard, cracked, or glazed disc makes the machine slip on slopes. Replacing either means removing a cover and some patience. If that's beyond you, a shop can do it, but book early.

How do I set the scraper blade and skid shoe clearance?

Set the scraper blade about 1/8 inch above pavement and an inch or more above gravel, then confirm against your manual. Park the machine on flat pavement, loosen the skid shoes, hold the scraper at your target height with a spacer, then lower the shoes to the ground and tighten both sides evenly. Too low and you gouge gravel or catch cracks. Too high and a skim of snow stays behind.

Single-stage machines rely on rubber auger paddles. Replace them as a pair when they're worn to the wear line or the throw gets weak. A set typically costs $30 to $90. On two-stage models, flip or replace a worn scraper blade, and replace skid shoes once they're thin, usually $15 to $50 a pair.

Finish by setting tire pressure to the number on the sidewall, equal on both sides. Uneven tires make the machine drift.

What should I do with old gas and fuel stabilizer?

Use fresh fuel in any machine that sat all summer, and add fuel stabilizer to gas that will sit again. Pump gas, especially ethanol blends, can start to degrade within a month or two and leave varnish in the carburetor. If the tank holds last winter's untreated gas, drain it into an approved container and take it to a local hazardous-waste drop-off, since rules vary by town. Don't top it off.

Do fuel work outdoors with the engine off and cool, away from flames and pilot lights. Small-engine makers generally approve fuel with up to 10 percent ethanol, but check your manual before filling. A bottle of stabilizer costs about $8 to $15 and treats many gallons; follow the label's ratio. At the end of winter, either run the carburetor dry or fill the tank with stabilized fuel and run the engine a few minutes so treated gas reaches the carb.

What's the schedule for cold and mild climates?

Cold-winter areas should finish everything by early November, while mild-winter areas can wait until late November or December. The order is the same in both; only the calendar shifts.

TimingCold-winter areasMild-winter areas
Late September to early OctoberRead the manual; inspect pins, belts, paddles, shoes; order parts, spare pins, and stabilizerNothing yet; keep the machine covered
Mid to late OctoberOil change, spark plug, grease; replace worn belts and friction disc; paddles, scraper, skid shoes, tire pressureInspect parts and order what's worn
Early NovemberDrain old gas, add fresh stabilized fuel, test run; spare pins and clearing tool by the doorNothing yet
Late November to DecemberFill a fuel can and keep the machine easy to reachOil, plug, pins, belts, scraper, shoes, fresh fuel, test run
When snow is forecastStart it, top off the tank, clear a path to itSame, a day or two before the storm

Where snow is rare, one session in late November or December is plenty. A machine that runs twice a winter mainly needs fresh gas and a new plug.

What does a good test run look like?

A good test run starts in a pull or two, idles without surging, and throws a clean, even arc. Run it outdoors for a few minutes to warm up, then engage the augers and listen. A squeal points to a belt, a rattle to a loose shoe or pin, and grinding means stop and look.

Rotate the chute through its full range and tilt the deflector. Drive forward and in reverse; if the wheels slip with no load, check the friction disc. Look under the machine afterward for drips.

Tonight, pull the plug wire, check the shear pins, and pour a fresh tank. Then put a spare pin and the clearing tool by the door.

Questions people ask

How often should I replace snow blower shear pins?

Replace them when they're bent, rusted, or snapped; there's no set interval. Many people swap them once a season while the machine is already open, since the pins cost only a few dollars. Always use the manufacturer's part.

Can I use car motor oil in a snow blower?

Often, yes, if the grade and rating match what your manual specifies, such as 5W-30 for many four-stroke engines. Check the manual for the right grade at your lowest expected temperature. Two-stroke machines need a different oil mixed into the fuel.

Do electric snow blowers need pre-season maintenance?

They need less. Skip the oil, plug, and fuel work, but still inspect the paddles, scraper, and skid shoes, check the cord for damage or the battery charge, and test the controls. Store batteries as the maker directs.

Is it worth paying a shop to tune up a snow blower?

It can be, especially if you'd need to replace a belt or friction disc. Shop tune-ups often run roughly $100 to $250 depending on your area and any pickup fee, plus parts. Book in early fall, since waits grow once snow arrives.

What if I wait until the first forecast to start?

Do the fuel, shear pins, and a test run first. Oil and plug can follow the same day. Put off anything that needs a mail-order part until after the storm.

Sources and further reading

Elsewhere in Gardening