Low Voltage Lighting for Garden Statue: Watts and Sizing
Most statues need 3 to 15 watts of LED light, so the real decisions are beam angle, cable gauge, and whether solar can do the job.
Save to PinterestWe may earn a commission when you buy through links on this page. It never changes what we recommend. Learn more
The short answer
Most garden statues need 3 to 15 watts of LED light: one 3 to 4 watt fixture for a figure under 3 feet, two or three fixtures for a taller piece up to 6 feet. Add up the fixture wattage, multiply by 1.2 for a 20 percent margin, and buy a transformer rated at or above that number. Keep cable runs short or heavy enough to limit dimming.
- Typical cost
- $120 to $400 for a DIY single-statue kit; often $150 to $450 more if an electrician adds an outdoor outlet
- Time needed
- 2 to 4 hours
- Skill level
- Beginner
Key points
- A single statue usually needs 3 to 15 watts of LED light, so a small transformer, often 45 to 60 watts, covers it with room to spare.
- Total fixture wattage times 1.2 gives the minimum transformer size; round up to the next standard rating.
- A 25 to 40 degree beam set 3 to 6 feet from the base and aimed up 30 to 45 degrees suits most figures from 2 to 6 feet tall.
- Voltage drop dims the farthest fixture on long runs, and thicker cable or a shorter run fixes it.
- Solar works only for small statues, about 3 feet or under, in spots with 6 or more hours of direct sun. Larger pieces should be wired.
In this guide
- What does garden statue lighting need to do?
- How far away and at what angle should the lights go?
- How do I estimate total wattage per statue?
- How do I size the transformer?
- What is voltage drop, and how long can the cable run?
- Solar vs low-voltage statue lights: which should I use?
- What are the installation steps and safety checks?
A single statue rarely needs more than 15 watts of LED light, so the transformer is the easy part. Beam placement is where most installs go wrong, so start there.
What does garden statue lighting need to do?
Statue lighting needs to shape the figure with light and shadow, not flatten it with glare. Light from low and slightly to one side picks out the face, the folds of fabric, and the texture. A single bulb aimed straight at the front makes stone look like a cardboard cutout.
Aim for the face and upper body to be the brightest zone, with the statue reading brighter than the surrounding beds. Good low voltage lighting for garden statue setups come down to restraint: low wattage, careful aim, and usually a second fixture from a different angle for depth.
How far away and at what angle should the lights go?
For a 2-to-6-foot statue, set a 25 to 40 degree beam about 3 to 6 feet from the base and aim it upward at roughly 30 to 45 degrees. That is the starting point for garden statue uplighting, and you adjust from there after dark.
The geometry is simple. A 30 degree beam spreads to about 3 feet wide at 6 feet away, enough to cover a torso. A 60 degree flood at 3 feet is about 3.5 feet wide, which suits a squat, wide piece like a sitting frog but will spill onto the wall behind a slim one.
Fixture count scales with height: one for a figure under 3 feet, two for 3 to 4.5 feet, and two or three above that. Put the main light in front and slightly off-center, then add a softer fill from the opposite side.
Hide each fixture behind a low plant or add a glare shield so nobody sees the bulb. Keep beams out of windows and neighbors' sightlines.
How do I estimate total wattage per statue?
Multiply the number of fixtures by the actual wattage of each one. A typical LED spotlight draws about 3 to 7 watts, while older halogen spots draw roughly 20 to 50 watts each, so going LED shrinks the whole system.
| Statue height | Fixtures | Watts each (LED) | Total watts |
|---|---|---|---|
| 2 to 3 feet | 1 | 3 to 4 | 3 to 4 |
| 3 to 4.5 feet | 2 | 3 to 5 | 6 to 10 |
| 4.5 to 6 feet | 2 to 3 | 4 to 5 | 8 to 15 |
These are planning figures. Read the wattage printed on the fixture, not the "equivalent to 50 watts" claim on the box.
How do I size the transformer?
Multiply your total fixture wattage by 1.2, then buy a low-voltage transformer rated at or above that number. The extra 20 percent keeps the unit from running at its limit and leaves room for another light later.
Say you have a 5-foot figure with three 5-watt fixtures. That is 15 watts, times 1.2, for 18 watts. Transformers typically come in ratings such as 45, 60, 100, 150, 200, and 300 watts, so a 45 or 60 watt unit covers it. If the same transformer also feeds path lights or other statues, add those watts before you multiply. Expect roughly $60 to $200 for the transformer, depending on wattage, timer features, and build quality.
What is voltage drop, and how long can the cable run?
Voltage drop is the voltage lost along the cable, and for a typical statue load of 15 watts or less, about 100 feet of 14-gauge cable is a workable limit. Past that, the fixture farthest from the transformer goes dimmer than the nearest one. A 12-volt system has little to spare, so even a volt of loss shows.
Two things control it: the load the cable carries and its length. Thicker wire (a lower gauge number) loses less. As a rough calculation assuming copper conductors, a 10-watt load at the end of 100 feet of 16-gauge cable loses under 1 volt. At 20 watts over the same distance, 14-gauge cable is the safer pick, because 16-gauge would lose more than 1 volt. Treat the table as rough guidance and check the cable maker's chart for your exact numbers.
| Cable | Best for |
|---|---|
| 16-gauge cable | Loads under about 10 watts, runs up to about 100 feet |
| 14-gauge cable | Loads up to about 20 watts, or runs near 100 feet |
| 12-gauge cable | Heavier loads or runs beyond 100 feet |
The fixes are simple. Put the transformer as close to the statue as the outlet allows, step up to heavier landscape lighting cable, or use a higher voltage tap (many transformers offer 12, 13, and 14 volts) if the fixtures are rated for it. If the far light looks yellowish or dim, suspect the run before the bulb.
Solar vs low-voltage statue lights: which should I use?
Use solar only for a statue about 3 feet tall or smaller that gets 6 or more hours of direct sun; otherwise run wired low-voltage. Most solar lights are weak, fade through the night, and run shorter in fall and winter.
A single solar spotlight is fine for an accent glow on a small figure in an open bed. It won't model a 5-foot statue, and it will disappoint in shade. Wired fixtures deliver the same brightness every night and let you balance two or three lights. For a larger piece, we'd pick wired every time. A basic wired landscape lighting kit typically runs $120 to $400 including transformer, cable, and fixtures.
What are the installation steps and safety checks?
Install in this order: anchor the statue, place the transformer, lay the cable, connect the fixtures, then aim after dark. Set and anchor the statue first, because you aim the lights at its final position and a statue that tips or sinks will undo your aim.
- Call 811 before digging, even for a shallow trench.
- Mount the transformer near a GFCI outlet with a weatherproof in-use cover, at the height the manufacturer specifies.
- With the transformer unplugged, lay the cable on the surface and connect the fixtures.
- Plug in, test at dusk, adjust angles, and add a shield where glare shows.
- Bury the cable about 6 inches deep, or as local code and the manufacturer direct.
Your next step: measure the statue, pick the fixture count from the table, multiply the watts by 1.2, and measure the cable run from outlet to statue before you buy anything.
Questions people ask
Can I mix LED and halogen fixtures on one transformer?
You can as long as the combined wattage fits the transformer, but it's rarely worth it. Halogen fixtures draw several times the power of LED and can leave brightness uneven across the run. Swap the old fixtures to LED instead.
What color temperature looks best on stone or bronze statues?
Warm white, around 2700 to 3000 Kelvin, flatters most stone, concrete, and bronze. Cooler light near 4000 Kelvin can look harsh and bluish outdoors, though some people prefer it on white marble.
Can one transformer light several statues?
Yes, if the combined fixture wattage times 1.2 stays within the transformer rating and each cable run is short enough to avoid dimming. Separate cables from the transformer to each statue work better than one long daisy chain.
Will a bigger transformer make my lights brighter?
No. Brightness comes from the fixtures and the voltage reaching them. A larger transformer just has more capacity available, which helps if you add lights later.
Do I need a permit to light a garden statue?
A plug-in low-voltage kit usually doesn't, but adding a new outdoor outlet or hardwiring a transformer often does. Rules vary by city and county, so ask your local building department before any 120-volt work.
Sources and further reading
- Electrical Safety Foundation International Outdoor electrical safety guidance for homeowners
- U.S. Consumer Product Safety Commission Consumer product safety information and recalls for outdoor electrical products
- National Fire Protection Association Electrical and fire safety resources, including National Electrical Code background
Was this article helpful?