How to Reupholster a Dining Chair Seat: Steps and Costs
Most jobs need a staple gun, a screwdriver and new foam. Plan on 2 to 3 hours for your first chair, less for the rest of the set.
Save to PinterestWe may earn a commission when you buy through links on this page. It never changes what we recommend. Learn more
The short answer
Unscrew the seat from underneath, pull the old staples, and check the foam and plywood base. Replace flattened or crumbling foam, wrap it in batting, then cut fabric 3 to 4 inches larger than the board on every side. Staple the center of each side first, alternating, then work toward the corners. Expect roughly $25 to $80 per chair.
- Typical cost
- $25 to $80 per chair, often less per chair for a full set
- Time needed
- About 2 to 3 hours for the first chair, roughly an hour each after that
- Skill level
- Beginner
Key points
- Test the foam and the frame before you buy fabric, because flattened or crumbling foam means a new piece, not a patch.
- Cut fabric 3 to 4 inches larger than the seat board on every side so you have something to grip and staple.
- Staple the center of each side first, alternating front, back, left and right, and do the corners last.
- Budget roughly $25 to $80 per chair, with fabric the biggest variable in the price.
- Stop and hire an upholsterer if the chair rocks at the joints, has springs or tufting, or is a valuable antique.
In this guide
- What tools and materials do you need to reupholster a dining chair seat?
- How do you check the seat before you buy fabric?
- How do you remove a dining chair seat and strip the old fabric?
- How do you replace the foam and batting?
- How much fabric do you cut, and how do you pull it tight?
- What order do you staple the fabric in so wrinkles don't set?
- How do you put the seat back and check your work?
- When should you stop and call an upholsterer?
Before you buy a yard of fabric, flip the chair over and look for the screws. Most dining chair seats are a plywood board with foam on top, held to the frame by screws through the corner blocks. Reupholstering one comes down to three habits: check the foam first, cut the fabric generously, and staple in the right order. Do those and a first-timer can get a clean result in an afternoon. Skip them and you get wrinkled corners and a seat that sags again fast.
What tools and materials do you need to reupholster a dining chair seat?
You need a screwdriver, a staple remover, a staple gun, scissors, and four materials: fabric, foam, batting and spray adhesive. None of it is specialized, and the staple gun is the only item most households have to buy.
| Item | What to get | Typical cost |
|---|---|---|
| Upholstery staple gun | Manual heavy-duty model; check which staple sizes it takes | $20 to $50 |
| Staples | 3/8 inch is a common pick for plywood bases; too-short staples can pull out | $5 to $10 per box |
| Staple remover | Or a flat screwdriver plus needle-nose pliers | $5 to $15 |
| Upholstery fabric | About 1/2 to 1 yard per chair, more for stripes or large prints | $15 to $60 per yard |
| High-density foam | 1 to 2 inches thick, cut to seat size | $10 to $30 per piece |
| Polyester batting | Thin sheet to wrap the foam | $5 to $15 for several chairs |
| Spray adhesive | General-purpose type that is safe for foam | $8 to $15 |
| Black dust cover (cambric) | Optional, for a finished underside | $5 to $10 |
You'll also want a marker, a tape measure, a serrated bread knife for cutting foam, safety glasses and a dust mask.
Pick true upholstery fabric, not curtain cotton or anything stretchy. A medium-weight woven or a performance fabric is the safe call for a family dining table, since many are made to stand up to spills and wear. For a first attempt we'd pick a solid or a small pattern. Stripes and big prints need alignment on every chair and extra yardage.
How do you check the seat before you buy fabric?
Check three things first: how the seat is mounted, whether the foam is still usable, and whether the frame underneath is sound.
Turn the chair over. A screw-mounted seat has four screws, usually through wooden corner blocks, and comes off with a screwdriver. A drop-in seat sits inside the frame and is often held by friction or a few screws from below, so you can usually push it out. A stuck-on seat is glued or nailed to the frame. Prying it loose risks the wood, and recovering it in place is harder, so think twice before taking it on.
Now press the seat hard with your palm. If you feel the board through the foam, the foam is finished. Yellow or orange crumbs, or deep flat spots that don't spring back, mean the same thing. A sagging seat almost always needs new foam, not extra stuffing. If the foam is firm but only slightly flat, a fresh layer of batting can buy some time. If the chair is old enough to need recovering, we'd replace the foam anyway: it's cheap, and the cover is already off.
Last, grab each leg and rock the chair. Loose joints, a cracked rail or a split plywood board change the job. A cracked board can be replaced using the old one as a template, but a wobbly frame needs repair before any fabric goes on. If you bought the chair recently and something feels off, you can look for recalls at the U.S. Consumer Product Safety Commission.
How do you remove a dining chair seat and strip the old fabric?
Unscrew the seat from underneath, then pull every staple holding the old cover to the board, leaving a bare plywood base.
- Photograph the chair from the top, sides and underside. Pencil a number on the underside of each seat and its frame so they go back together in the same pairing.
- Remove the screws with a hand screwdriver and keep them in a labeled cup. Lift the seat free. If it's stuck, tap upward from underneath with the heel of your hand.
- Remove the dust cover if there is one. Save it as a template.
- Pull the staples. Slide a flat screwdriver under each staple to lift one leg, then grab it with needle-nose pliers. Hammer down any that break off flush.
- Peel off every layer of old fabric, batting and foam. If a previous owner covered over an old cover, take it all off down to the board.
- Inspect the board. It should be flat, solid and free of cracks. Sand off any glue ridges while wearing a dust mask.
How do you replace the foam and batting?
Trace the board onto new high-density foam, cut it slightly oversized, glue it down and wrap it in batting.
Lay the board on the foam and trace around it with a marker, adding about 1/4 inch all around so the edge crowns neatly over the board. Cut with a serrated bread knife, keeping the blade vertical and using long sawing strokes. One-inch foam suits a slim seat. Two inches is more comfortable but changes how the seat sits in the frame, so check clearance if it's a drop-in.
Spray the board and the foam's underside, then follow the can's directions for tack time before pressing the foam on. Most spray adhesives are flammable, so work outdoors or with windows open, away from pilot lights and open flames. Lay a sheet of polyester batting over the top, wrap it around the edges and pull it onto the underside. Staple it in a few spots, then trim the excess so it doesn't bunch where the fabric will sit.
The most common shortcut is reusing the old foam. Torn or crumbling foam leaves a lumpy surface that shows through the new fabric, and spending $10 to $30 on a fresh piece saves you from redoing the seat.
How much fabric do you cut, and how do you pull it tight?
Cut the fabric 3 to 4 inches larger than the seat board on every side, which leaves enough to grip while you pull and staple.
Measure the board at its widest and deepest points. A board 18 inches wide and 17 inches deep needs a piece around 25 by 24 inches. Skip the allowance and the fabric ends up short on one side, you can't pull it taut, and there's nothing left to staple.
Lay the fabric face down on a clean floor and set the padded board on top, foam side down, centered. For a stripe or print, line the pattern up with the front edge of the chair and mark the front center in pencil on the back of the fabric. Repeat the same placement on every chair in a set.
Aim for taut, not stretched. The fabric should be firm enough to show no ripples across the seat. Pull so hard that the weave distorts or stripes bow, and the pattern will sit crooked once it relaxes.
What order do you staple the fabric in so wrinkles don't set?
Staple one point at the center of each side first, alternating across from each other, and leave the corners for last. Stapling the whole front edge first locks in slack you can't pull out from the back.
- Anchor the front. Fold the fabric over the front edge and place one staple in the center of the board's underside, about 1/2 to 1 inch in from the edge.
- Anchor the back. Pull the fabric taut toward the rear and place one staple at the center of the back edge.
- Anchor the sides. Repeat on the left center, then the right center, pulling firmly each time.
- Check from the top. Flip the seat over. If the pattern is crooked or you see ripples, pull the staple on that side and reset it. Fixing it now takes a minute.
- Work outward. Add staples about 1 inch apart, moving from each center toward the corners and alternating sides so tension stays even. Stop 2 to 3 inches short of every corner.
- Do the corners last. Pull the fabric diagonally over the corner, fold the excess into a flat pleat and staple it down. A squared corner wants one tight fold. A rounded corner takes several small pleats. Trim the bulk so it doesn't pile up under the staples.
- Trim and finish. Cut the extra fabric about 1/2 inch from the staples. For a clean underside, cut a dust cover slightly smaller than the board, fold the edges under and staple it down.
An upholstery staple gun leaves staples flush if you press the nose firmly against the board. If one sits proud, tap it down with a hammer. Pull and replace any that miss the board or bend over.
How do you put the seat back and check your work?
Set the seat into the frame, line up the original screw holes and drive the screws by hand until snug. Hand tightening keeps you from stripping holes in old corner blocks.
Start each screw by turning it slowly backward until you feel it drop into its old thread, then turn it forward. Stop when it's firm, because overtightening can crack a block or drag fabric into the hole. Sit down and shift your weight. The seat should feel solid, with no creaking or movement.
Run your hand over the surface and edges for loose staples or ripples, then look at the pattern from a few feet away to confirm it runs straight.
When should you stop and call an upholsterer?
Call a professional if the frame is cracked or loose at the joints, if the seat has springs or webbing, or if the chair is a valuable antique. New fabric won't fix a structural problem.
- Loose or cracked joints. A chair that rocks when you push on the back needs regluing and clamping first.
- Springs, webbing or horsehair stuffing. Traditional hand-built seats are not a first project.
- Antiques and old finishes. Prying and restapling can cut a piece's value. Chairs painted before 1978 may carry lead paint, so don't sand or scrape a finish you haven't had tested.
- Tufting, buttons, welting or an upholstered back. These call for sewing and pattern skills beyond a wrap-and-staple seat.
- Glued-on seats you can't free. If getting one off means risking the frame, stop.
A professional often charges roughly $50 to $150 or more per dining chair seat, depending on region, fabric and how much frame repair is needed. For a plain set of six in good frames, DIY saves real money. For one inherited chair worth more than the repair, the pro fee is cheap insurance.
Start with one chair this weekend: unscrew the seat, press the foam, and decide from there whether you're buying fabric or calling for a quote.
Questions people ask
Can I put new fabric over the old fabric?
You can in a pinch, but it rarely looks good. Old staples and worn fabric show through as bumps, and the extra layers make corners bulky. Stripping to the board doesn't take long and gives a cleaner result.
How much fabric do I need for six dining chairs?
For standard seats about 18 by 18 inches on 54-inch-wide fabric, plan on roughly 2 to 2.5 yards for six chairs, since two seats fit side by side. Add extra for stripes or large prints that need matching. Measure your board and add 3 to 4 inches per side before you buy.
What thickness of foam should I use on a dining chair seat?
One inch works for slim seats and chairs with little clearance, and 2 inches is more comfortable for long meals. Use high-density foam either way. If the seat drops into the frame, test-fit the thickness before gluing.
Can I use upholstery tacks and a hammer instead of a staple gun?
Yes, but it's slower and less forgiving. You'll need to space the tacks evenly and watch for bent tacks and hammer marks on the fabric. A manual staple gun costs little and gives more even results.
Why does my new fabric have wrinkles near the corners?
Usually the corners were stapled too early, or the fabric wasn't pulled evenly from the center outward. Pull the corner staples, check that the side staples are taut, and refold the excess into a tight, flat pleat before stapling again.
Sources and further reading
- U.S. Consumer Product Safety Commission Check chairs and other furniture for recalls and safety notices
- CPSC Anchor It Tip-over safety guidance for dressers, TVs and other heavy furniture
Was this article helpful?