Pear Deck or Pier Deck? How Pier-Supported Decks Work
Pier decks suit slopes, rock, and tight yards. Here's how the footings carry load, what they cost, and when an engineer is worth paying.
Save to PinterestWe may earn a commission when you buy through links on this page. It never changes what we recommend. Learn more
The short answer
A pier deck is held up by individual concrete or steel footings; Pear Deck is unrelated Google Slides software. Each pier carries one post and spreads its load into soil. Piers often sit 6 to 8 feet apart and must reach below your local frost line, and a wood pier deck typically costs roughly $30 to $60 per square foot.
- Typical cost
- $1,200 to $6,000 for 8 to 12 poured piers; full wood deck about $30 to $60 per square foot
- Time needed
- Piers: one to three days plus curing. Full deck: one to three weeks
- Skill level
- Intermediate
Key points
- Pear Deck is classroom software; the building term you want is pier deck.
- Each pier carries one post's share of the load, so footing size depends on soil bearing capacity and how much deck that post supports.
- Piers beat a continuous footing on slopes, rocky ground, and tight sites because you dig a few holes instead of a long trench.
- Poured concrete piers below frost depth are the sensible default; helical piers earn their higher price in soft soil or where digging is hard.
- Tall posts, steep slopes, hot tubs, and doubtful soil are the cases where you should pay for an engineer's review.
In this guide
- Is Pear Deck the Same as a Pier Deck?
- What Is a Pier Deck and How Does It Carry Load?
- When Does a Pier Deck Beat a Continuous Footing?
- How Far Apart Should Deck Piers Be, and How Do Posts Connect?
- Which Pier Type Should You Use: Poured, Precast, or Helical?
- What Does a Pier-Supported Deck Cost?
- When Does a Pier Deck Need an Engineer or Permit Review?
A pier deck sits on separate concrete or steel footings instead of a continuous wall or trench, and it's often the practical choice on sloped, rocky, or cramped ground. Pear Deck, which turns up in the same searches, is a Google Slides add-on for classrooms. Nothing about it involves lumber.
Is Pear Deck the Same as a Pier Deck?
No. Pear Deck is classroom software, and a pier deck is a deck supported on separate piers; the two only sound alike. There's no "pear deck" framing method or lumber grade. If a listing or a voice-to-text quote says "pear deck," read it as a typo and ask for the footing details in writing: pier diameter, depth, spacing, and the hardware that connects each post.
What Is a Pier Deck and How Does It Carry Load?
A pier deck rests on separate vertical supports, each bearing on its own footing in the ground, instead of on a continuous wall, slab, or trench footing. The weight follows a simple path: deck boards to joists, joists to a beam, the beam to posts, and the posts to piers that spread the load into soil.
That last step is where the numbers matter. Residential decks are commonly designed for about 40 pounds per square foot of live load plus 10 pounds of dead load, so roughly 50 pounds per square foot. Presumptive soil values in codes commonly start around 1,500 pounds per square foot for ordinary soils, though a soil test or local rule can change that. As a rough illustration, say one post carries a 100-square-foot patch of deck. That's about 5,000 pounds. A round footing 24 inches across has about 3.1 square feet of bearing area, good for roughly 4,700 pounds at 1,500 pounds per square foot. That falls just short, so you'd widen the footing to 30 inches or add a post. Soft clay or loose fill bears less. Treat this as a sketch of the logic, not a design. Your local footing tables control.
Width is one question and depth is another. Piers have to reach below the frost line where soil freezes, or heaving will lift and twist the deck. Our deck footing depth guide covers the frost, soil, and code numbers.
When Does a Pier Deck Beat a Continuous Footing?
A pier deck wins when digging a continuous trench is slow, expensive, or impossible. On a sloped lot, you cut posts to different lengths and keep the deck level without regrading the yard. On rocky or rooty ground, you only need to find 6 to 12 workable spots instead of 30 feet of clear trench. In tight side yards, a hand auger or a small machine reaches places a trencher can't.
The cheaper alternative is a low platform on precast deck blocks. That's fine for a small freestanding deck a few inches above stable, well-drained ground. It can shift with the soil, and many codes won't accept it once the deck attaches to the house or climbs higher. For most attached decks on diggable soil, we'd pick poured concrete piers below frost depth. They're inexpensive, familiar to every inspector, and hard to get wrong.
How Far Apart Should Deck Piers Be, and How Do Posts Connect?
Most wood decks put piers about 6 to 8 feet apart along each beam, but your actual spacing comes from beam size, joist span, and the span tables your local code uses. A doubled 2x10 beam can span farther than a doubled 2x8. Heavier decking, a hot tub, or a snow load shortens that span. Use the prescriptive tables your building department references, such as the IRC deck provisions or the American Wood Council's DCA 6 guide, not a rule of thumb from a neighbor.
Connections matter as much as spacing. There are two sound ways to join post to beam: notch a pressure-treated 6x6 post and bolt a doubled beam on both sides, or set the beam on top of the post with a rated cap connector. Don't notch a 4x4, because the notch removes too much wood. At the bottom, a metal post base holds the post about 1 inch above the concrete so end grain stays out of standing water. It anchors with a cast-in bolt or a properly set epoxy anchor.
Use hot-dip galvanized bolts, plus connectors and joist hangers rated for treated lumber, because ordinary plated hardware can corrode against modern preservatives. Tall posts also need diagonal bracing; a deck 5 or 6 feet in the air on slender posts will sway. If the deck attaches to the house, the ledger is the other half of the structure. Read our guide to deck ledger board mistakes before you fasten anything to the rim joist.
Which Pier Type Should You Use: Poured, Precast, or Helical?
For most decks, poured concrete piers are the right choice, and helical piers make sense where digging or concrete is the problem. Precast blocks fit only the lowest, simplest decks.
| Pier type | Typical cost | Best for | Watch for |
|---|---|---|---|
| Poured concrete piers (tube forms) | $150 to $500 per pier installed | Attached or freestanding decks on diggable soil | Must reach below frost depth; needs several days to cure before heavy loads |
| Precast blocks | Under $50 per block | Low, freestanding decks on stable ground | Can shift or heave; many codes reject them for attached or elevated decks |
| Helical piers | $400 to $1,200 per pier installed | Soft soil, tight access, no-dig or no-concrete jobs | Boulders can stop the screw; installer minimum fees apply |
Helical piers are steel shafts with screw plates, driven by machine. The installer reads torque as the pier goes in, which gives a practical check on capacity. Where bedrock sits near the surface, the fix is usually a pier drilled and pinned into the rock. That's a job for an engineer and a licensed contractor, not a weekend.
What Does a Pier-Supported Deck Cost?
A wood pier-supported deck usually runs about $30 to $60 per square foot, with the piers alone at roughly $1,200 to $6,000 for 8 to 12 poured concrete piers. Decking, railings, and stairs make up most of the total, so the piers are the smaller line item. Treat all of these as typical U.S. ranges that swing with your region.
Several things push the price up. Slopes mean taller posts and more bracing. Rock or roots mean slower digging and sometimes a drill rig. Poor access means hand labor. Helical piers cost more per pier than concrete, though they can save money when digging is miserable. Budget for a permit fee, often somewhere between $50 and $500, and for an engineer's letter or drawings, which commonly run a few hundred dollars to $1,000 or more on complicated sites.
When Does a Pier Deck Need an Engineer or Permit Review?
Get an engineer, or at least a thorough permit review, when the deck is tall, heavy, on a steep slope, or on soil you can't vouch for. The prescriptive tables cover ordinary decks and stop being reliable outside those limits. Common triggers:
- Posts taller than a few feet, or a deck high enough to need guards, which codes commonly require above 30 inches
- A hillside lot, fill soil, soft clay, or signs of past slope movement
- A hot tub or spa, since a filled spa can weigh several thousand pounds
- High-wind, heavy-snow, or seismic areas with stricter local rules
- Multi-level decks, or any deck over living space
Permit rules are local. Many jurisdictions require one for any attached deck or any deck more than 30 inches above grade, and some inspect the footing holes before you pour. Call the building department before you buy lumber, and hire a licensed engineer or contractor for anything the local tables don't cover.
Your next step: sketch the deck footprint, mark where each post would land, then call 811 and your building department for the local deck handout.
Questions people ask
How deep do deck piers need to go?
Below your local frost depth, which your building department can tell you. In warm regions with no frost, codes still set a minimum depth, and footings must sit on solid, undisturbed soil.
How many piers does a 12x12 deck need?
Often 3 to 6, depending on the layout. An attached deck might use a ledger on the house plus one beam line with 3 posts, while a freestanding deck needs two beam lines. Your beam size and span tables set the final count.
Can I build a pier deck on a slope without grading?
Usually yes, and that's one of its main advantages. You cut each post to a different length to keep the deck level. Steep slopes and tall posts need bracing and often an engineer's review.
Are precast deck blocks allowed for a pier deck?
They're sometimes accepted for low, freestanding decks, but many local codes don't allow them for attached or elevated decks. Blocks also sit on top of the soil, so they can shift or heave. Ask your building department before relying on them.
Can a homeowner pour deck piers without a pro?
Poured concrete piers are a reasonable DIY job if you have a permit, call 811, and follow the span and depth rules. Digging, setting tube forms, and mixing concrete is heavy work. Helical piers and rock-pinned piers are best left to installers.
Sources and further reading
- 811 Call Before You Dig Free utility locating before you dig post holes
- Cooperative Extension (extension.org) Find your local Extension office for regional soil guidance
Was this article helpful?