Deck Screws for Pressure Treated Wood: What to Buy
Modern treated lumber corrodes cheap fasteners fast. Here's which coatings hold up, which features are marketing, and when stainless pays off.
Save to PinterestWe may earn a commission when you buy through links on this page. It never changes what we recommend. Learn more
The short answer
For most backyard decks built with ACQ or copper azole treated lumber, use #10 star drive screws labeled for treated wood, with a ceramic or polymer coating or a hot-dip galvanized finish. Choose stainless near salt water, with cedar or redwood, or for no rust streaks. Budget roughly $60 to $180 in screws for a 200-square-foot deck, versus $160 to $540 for stainless.
- Typical cost
- $60 to $180 in screws for a 200 sq ft deck (coated or galvanized); $160 to $540 for stainless
- Time needed
- About an hour to choose and buy; fastening time depends on deck size
- Skill level
- Beginner
Key points
- Modern preservatives (ACQ, copper azole, micronized copper) corrode plain or thinly plated steel, so a box that doesn't say it's approved for treated lumber stays on the shelf.
- Coating or metal grade drives corrosion resistance, while drive type, length, and tip design drive how easily the screw installs and holds.
- Stainless is worth the money near salt water, with cedar or redwood, or when you never want to re-screw the deck; how close counts as near depends on local conditions.
- Color-matched heads, long warranties, and brand-specific thread names rarely change performance on a treated-wood deck.
- Deck screws don't replace the bolts, structural screws, and connectors that hold the ledger and railing posts.
In this guide
- Why does fastener choice matter more on treated lumber?
- Which coatings and features actually matter?
- Which screw features don't justify the price?
- How do coated, galvanized, stainless, and hidden fasteners compare?
- What do deck screws cost, tier by tier?
- How do you match screws to your wood and location?
- What's the best screw for a typical backyard deck?
The right deck screws for pressure treated wood are the ones whose box says they're approved for treated lumber, so check that before you check the price. A 200-square-foot deck takes roughly 700 screws, which makes the choice cheap to get right and miserable to fix after the boards are down. Coated or hot-dip galvanized screws handle most backyard decks. Stainless pays off in a short list of situations, sorted out below.
Why does fastener choice matter more on treated lumber?
Fastener choice matters more on treated lumber because the copper in modern preservatives attacks plain steel and thin zinc plating, and it does so fastest when the wood is wet. Residential lumber moved away from CCA years ago to formulas like ACQ, copper azole (CA), and micronized copper (MCA). They resist rot and insects well, but the copper sets up a corrosion reaction with unprotected steel and zinc. Treated boards are often sold still wet, which speeds it along.
The failure is predictable. Interior-grade or thinly plated screws can rust badly within a few seasons, heads snap, and board ends lift. You'll notice a loose, squeaky board first, then a screw head that shears off underfoot.
Check the plastic tag stapled to the end of a board. It names the preservative and the exposure rating, which tells you what the fastener has to survive.
Which coatings and features actually matter?
Four finishes matter on a treated deck: ceramic or polymer coatings, hot-dip galvanizing, 304 stainless, and 316 stainless. Plain zinc plating doesn't belong on the list.
Among coated options, ceramic coated deck screws carry several baked-on layers over hardened steel and are made for treated wood. They drive cleanly and hold well. The weak point is the coating itself, since a slipping bit or an overdriven head can scar it, and scarred spots are where rust starts.
The other common choice is hot-dip galvanized deck screws, which have a thick zinc layer applied by dipping. The finish is dull gray and slightly rough. That thickness handles copper-treated wood well, but it can clog a small drive recess, so use a snug bit. You'll find hot-dip galvanizing more often on nails and connector hardware than on decking screws.
Then there are stainless steel deck screws, usually 304 (sometimes sold as 18-8). They don't react with the copper in the wood and resist rust well inland. The tradeoff is softer metal that snaps more easily and needs a pilot hole near board ends. For salt air, step up to 316 stainless, which contains molybdenum for better chloride resistance. It's the right call near the ocean or a saltwater pool. How far inland you need it depends on local conditions, so ask a local lumberyard.
Beyond the metal, four features affect how the screw installs and holds:
- Star drive (T25 is typical): It resists cam-out far better than Phillips, which protects the coating and your wrists.
- Diameter: #10 is the common choice for decking. #8 can work for lighter jobs but gives less margin.
- Length: Use 2½-inch screws for 5/4 boards over joists and 3-inch screws for 2x boards, so the thread reaches about 1½ inches into the joist.
- Tip and head: A sharp or self-drilling tip and a bugle head with small nibs reduce splitting and let the head sink flush.
Which screw features don't justify the price?
Color-matched heads, long warranties, and brand-specific thread names rarely change how a screw performs on a pressure-treated deck. Matched heads are worth something on composite decking, where the screw stays visible. On treated wood you'll stain, nobody sees them after a season.
Read warranty language before you let it sway you. Many cover the screw itself, not the boards or the labor to replace them. Proprietary thread names are mostly variations on a coarse thread, a sharp tip, and nibs under the head.
The other big upcharge is hidden deck fasteners. They need grooved boards or a slotting tool, they take longer to install, and they suit stable, dry boards. Newly delivered treated lumber is the opposite, because it shrinks and cups as it dries. Clips can work with kiln-dried or grooved boards, but they still rely on screws that need the same corrosion resistance. For a standard treated deck, face-screwing is simpler and holds well.
How do coated, galvanized, stainless, and hidden fasteners compare?
Coated screws win on value, hot-dip galvanized wins for framing hardware, stainless wins on longevity, and hidden systems win only on looks. Prices below are rough U.S. ranges per pound and vary by size, box count, and retailer.
| Type | Corrosion resistance | Best use | Drawbacks | Typical price per pound |
|---|---|---|---|---|
| Ceramic or polymer coated | Good inland, if rated for treated wood | Deck boards and framing on typical yards | Coating can chip if the bit slips or the head is overdriven | $6 to $12 |
| Hot-dip galvanized | Good to very good | Framing; connectors where the maker specifies it | Fewer decking sizes; thick zinc can clog the drive | $8 to $15 |
| 304 stainless | Excellent inland | Deck boards, railings, cedar or redwood | Softer, snaps easily; needs pilot holes near ends | $18 to $35 |
| 316 stainless | Best, resists salt | Coastal decks, saltwater pools | Highest cost | $25 to $45 |
| Hidden fastener systems | Depends on the clip and screw | Grooved boards, composite | Slower; poor fit for wet, square-edge treated boards | Varies; can add a few hundred dollars or more on a mid-size deck |
What do deck screws cost, tier by tier?
Expect roughly $60 to $180 in screws for a 200-square-foot deck at the coated and galvanized tiers, and $160 to $540 at the stainless tiers. A deck with 5/4 boards on 16-inch joist spacing uses about 3 to 4 screws per square foot, with two screws at every joist crossing. That's around 700 screws for 200 square feet, including about 10 percent overage. A pound of 2½-inch #10 screws holds roughly 60 to 80, so plan on about 9 to 12 pounds.
| Tier | Typical price per pound | Approx. cost, 200 sq ft deck | What you get |
|---|---|---|---|
| Value coated | $6 to $10 | $55 to $120 | Treated-wood rating, star drive, standard coating |
| Premium coated or galvanized | $10 to $15 | $90 to $180 | More coating layers or thicker zinc, better tips |
| 304 stainless | $18 to $35 | $160 to $420 | Rust resistance inland, softer metal |
| 316 stainless | $25 to $45 | $225 to $540 | Marine-grade resistance |
When you compare price per pound, stay within the same size. A pound of #8 screws holds more pieces than a pound of #10 in the same length, so cost per 100 screws is the fairer yardstick. Bulk boxes of 5 or 25 pounds usually cost much less per pound than one-pound packs.
Stainless can add a few hundred dollars to a deck that costs thousands, so it's a small slice of the total. It's wasted on an inland pressure-treated deck with properly coated screws. It can be cheap insurance if you hate the idea of re-screwing boards years from now.
How do you match screws to your wood and location?
Match the screw to the preservative in your boards first, then to how close you are to salt water. Start with the end tag on your lumber.
- ACQ, CA, or MCA treated wood, inland: Look for any box that says approved for treated lumber, in a ceramic or polymer coating or hot-dip galvanized.
- Near the coast or a saltwater pool: Use 316 stainless for boards and any exposed fasteners.
- Cedar or redwood decking: Use stainless, because the natural tannins can stain and corrode many steel fasteners.
- Framing connectors: Use hot-dip galvanized or stainless joist hanger hardware, fastened with the nails or structural screws the connector maker lists. Don't fill hanger holes with ordinary deck screws.
New treated boards are often wet. Set them close to tight, since they shrink as they dry, and follow the board maker's gap guidance for kiln-dried boards (about 1/8 inch is common).
What's the best screw for a typical backyard deck?
For a typical backyard deck with ACQ or CA-treated framing and boards, the best choice is #10 star drive screws with a multi-layer ceramic or polymer coating labeled for treated lumber. Use 2½-inch screws for 5/4 boards and 3-inch screws for 2x boards. That setup resists the copper in the wood, installs fast, and costs a fraction of stainless.
Upgrade to 316 stainless near salt water, and to 304 stainless with cedar or redwood or if you want the lowest-maintenance result. Use hot-dip galvanized connectors and the fasteners their manufacturer specifies for the framing. Skip hidden clips unless you've chosen grooved boards and are willing to let them dry.
Your next step: check the end tag on your lumber, count 3 to 4 screws per square foot, buy about 10 percent extra, and test a few in scrap boards before you commit to a full box. If you haven't set footings yet, call 811 a few days before you dig.
Questions people ask
Can I use drywall or interior screws on a deck?
No. Drywall and interior screws are brittle and thinly coated, so they snap under load and rust quickly in wet, copper-treated wood. Use screws made for exterior decking and labeled for treated lumber.
Do stainless screws react with pressure-treated wood?
They resist the corrosion that copper preservatives cause, which is why stainless is a safe pairing. The caution is mechanical: stainless is softer and can snap, so pilot-drill near board ends and drive at moderate speed.
Are galvanized nails okay instead of screws?
Hot-dip galvanized nails are fine for some framing connections, and connector makers often specify them for joist hangers. For deck boards, screws resist pulling up better and let you remove a board later without damage.
Do I need to pre-drill treated lumber for deck screws?
Usually not in the middle of a board if the screws have sharp or self-drilling tips. Pilot holes help near board ends, in dense or dry boards, and with stainless screws.
Can I mix stainless screws with galvanized connectors?
Check the connector maker's instructions first, since they list the fasteners their hardware is rated for. As a general rule, match the metal types where fasteners and connectors touch to limit extra corrosion.
Sources and further reading
- Cooperative Extension (extension.org) Cooperative Extension home and garden project guidance
- 811 Call Before You Dig Free utility locating before you dig deck footings
Was this article helpful?