Fix and Furrow
Advertise

Deck Footing Depth: Frost Line, Soil, and Code Numbers

Your building department gives you two of the three numbers. The soil in your own yard decides the third.

Save to Pinterest

We may earn a commission when you buy through links on this page. It never changes what we recommend. Learn more

Concrete tube form set in a dug hole for a deck footing before the pour
Photo: d c on Unsplash

The short answer

Deck footing depth is the deepest of three numbers: your local frost depth, the minimum in your adopted building code, and the depth needed to reach undisturbed, load-bearing soil. Frost depth runs from near zero along the Gulf Coast to 48 inches or more in the far north, so get the exact figure from your building department before you dig.

Typical cost
Roughly $60 to $150 per footing in DIY materials, depending on depth and hardware
Time needed
One to two days of digging and pouring, plus curing and inspection wait
Skill level
Intermediate

Key points

  • Footings must sit below the local frost line, and the building department's number overrides any generic chart.
  • Model code generally also requires deck footings to reach undisturbed soil at least 12 inches down, even where frost is not a concern.
  • Weak soil like clay calls for a wider footing, not usually a deeper one.
  • A 16 to 18 inch round footing is a common starting point for 4x4 or 6x6 posts, but the load math and your inspector decide the final size.
  • Call the building department before you dig, and leave the holes open for the footing inspection.
In this guide
  1. What does a deck footing actually do?
  2. Why does the frost line set the minimum depth?
  3. How do I find my local frost depth and code minimum?
  4. How does soil type change the footing size?
  5. How do footing diameter, post size, and load work together?
  6. What happens when shallow footings heave?
  7. Do I need a permit and inspection for deck footings?
  8. What should I ask my building department?

Your deck footing depth is the deepest of three numbers: the local frost depth, the minimum written into your adopted code, and the depth where you hit undisturbed, firm soil. Frost depth alone runs from near zero along the Gulf Coast to 48 inches or more across the northern states, so a generic chart is useless. One call to your building department settles most of it.

What does a deck footing actually do?

A deck footing spreads a post's weight over enough soil to hold it up, and it anchors the post so the deck doesn't shift with the ground. Width handles the load. Depth handles the weather.

A bare post would punch into the soil under it. A wider concrete base spreads the same weight over more ground, and it has to sit deep enough that seasonal freezing never reaches the soil beneath it.

Why does the frost line set the minimum depth?

The frost line is the deepest point the ground is expected to freeze in a normal winter, and footings go below it so the soil underneath stays unfrozen and can't lift them. Wet soil expands as it freezes, and ice layers can keep drawing water from below and growing, which pushes upward with real force.

Silty and clay soils are the worst offenders because they hold water and wick it upward. Clean gravel drains and heaves far less. Frozen soil can also grip the sides of a concrete footing and drag it up as it rises, which is why smooth tube forms help.

How do I find my local frost depth and code minimum?

Ask your local building department, because the frost depth it has adopted is the figure the inspector will hold you to. Most U.S. jurisdictions build from the International Residential Code, which generally requires deck footings to extend below the frost line and at least 12 inches below undisturbed ground. Many towns amend that, and some publish a specific depth in inches.

Don't rely on frost maps you find online. They show averages, and your town may have adopted something deeper. The USDA Plant Hardiness Zone Map won't help either, since it tracks minimum air temperature, not how far frost reaches into the ground.

Some places allow shallower footings for freestanding decks or frost-protected designs. Others don't. Get the answer in writing, or note who gave it to you.

How does soil type change the footing size?

Weaker soil needs a wider footing, because the soil's bearing capacity decides how much area each footing needs to carry its load. The model code lists presumptive values for when you haven't had the soil tested, and the table below uses those approximate figures for a footing carrying about 2,400 pounds.

Soil typePresumptive bearing capacityRound footing diameter needed
Clay, sandy clay, silty clayAbout 1,500 lb per sq ftAbout 17 to 18 inches
Sand, silty sand, clayey sandAbout 2,000 lb per sq ftAbout 15 to 16 inches
Gravel, sandy gravelAbout 3,000 lb per sq ftAbout 12 inches

Treat those as a sanity check, not a design. A local soil survey usually lists your county's soil types, and your Cooperative Extension office can point you to it.

Fill is the trap. Soil that was placed and not compacted, common near new construction and old foundations, settles unpredictably, so dig through it to undisturbed ground. If the hole bottoms out in soft or organic soil, stop and get an engineer's opinion. Expansive clay and steep slopes call for the same. A geotechnical or structural engineer's site visit often costs several hundred dollars or more, which is still a small fraction of a rebuilt deck.

How do footing diameter, post size, and load work together?

Each footing's required area equals the load on its post divided by the soil's bearing capacity, so diameter falls out of the load and the soil. Code design typically assumes about 40 pounds per square foot of live load plus roughly 10 pounds of dead load, and snowy regions often require more.

Here's a worked example. A post that supports 48 square feet of deck (say 8 feet by 6 feet) carries about 2,400 pounds at 50 pounds per square foot. In 1,500-pound clay, that needs 1.6 square feet, or a round footing about 17 inches across. In 3,000-pound gravel it needs 0.8 square feet, about 12 inches. Closer post spacing means each footing carries less, but you dig more holes.

Post size matters too. Code commonly limits a 4x4 post to about 8 feet of height, while 6x6 posts handle taller runs and give the beam more bearing surface. For an attached deck in frost country we'd pick 6x6 posts on round concrete footings at least 16 inches across, and go wider in clay. Concrete is cheap next to redoing a footing.

A 16-inch tube dug 48 inches deep takes roughly 9 to 10 bags of 80-pound concrete mix. Set the post on a metal post base with a standoff rather than burying it in the concrete, so the wood stays off wet ground.

Wear gloves, eye protection, and a dust mask when mixing, because wet concrete burns skin. A gas-powered auger can kick hard if it catches a rock, so use hearing protection, keep a firm stance, and consider a two-person model.

What happens when shallow footings heave?

Shallow footings rise unevenly in winter and often don't settle back to where they started. The deck racks out of level, boards cup and gap, and stair stringers pull away from their landings.

On an attached deck the damage reaches the house. A footing that lifts an inch pushes against the ledger and strains its fasteners over repeated winters.

The fix is digging out and resetting the footings, which costs far more than digging them right. Where frost is very deep or the soil is poor, helical piles are an alternative. They are steel screws driven to stable soil by specialists, and they often cost several hundred to well over a thousand dollars each installed, depending on depth and region.

Do I need a permit and inspection for deck footings?

Almost certainly yes for any attached deck, and often for freestanding decks more than 30 inches off the ground or larger than about 200 square feet. Those are common model-code thresholds, and your town may be stricter. Permits typically come with a footing inspection, done with the holes open and forms in place before any concrete goes in.

What should I ask my building department?

Ask these questions in one call, and write down the answers with the date and the name of the person you spoke with:

  1. What frost depth do you enforce, in inches?
  2. Which code edition and local amendments apply to decks?
  3. Do I need a permit for this deck, and for footings specifically?
  4. What soil bearing capacity do you assume without a soil test?
  5. What is the minimum footing diameter for my post spacing and snow load?
  6. Do you allow shallower or frost-protected footings for a freestanding deck?
  7. When do you inspect, and how much notice do you need?
  8. Do you accept a third-party engineer's report if the soil is questionable?

Make that call before you buy lumber or rent an auger, and put the frost depth number on your plans.

Questions people ask

Can I pour deck footings in winter?

You can, but concrete must not freeze while it cures, which takes insulating blankets or heated enclosures. Frozen ground also has to be thawed or dug through to reach the right depth. Most people wait for milder weather.

Do freestanding decks need footings below the frost line?

It depends on your jurisdiction. Some codes allow shallower footings for decks that don't attach to the house, and others still require full frost depth. Ask your building department before assuming either.

Is gravel in the bottom of the hole necessary?

A few inches of compacted gravel can help seat the footing and drain the base, and some inspectors expect it. It doesn't replace going below the frost line. Follow your local code and inspector.

Can I use precast concrete deck blocks instead of poured footings?

Deck blocks sit on the surface, so they move with frost and don't substitute for frost-depth footings. Some places permit them for low, freestanding decks. Check local rules first.

How long should concrete cure before I build on the footings?

Many builders wait at least 48 to 72 hours before setting posts and loading them lightly, and longer before heavy loads. Follow the mix manufacturer's directions and your inspector's guidance, especially in cold weather.

Sources and further reading

Elsewhere in Landscaping