Part of our Fencing and Yard Costs guide
Deck Board Replacement Cost: What You'll Pay in 2026
Keeping a sound frame and swapping only the boards usually costs less than a rebuild, unless the joists have other plans.
Save to PinterestWe may earn a commission when you buy through links on this page. It never changes what we recommend. Learn more
The short answer
Replacing deck boards on a sound frame costs about $5 to $10 per square foot installed for pressure-treated pine and $10 to $22 for composite or PVC. For a 12x16 deck, that's roughly $1,000 to $4,200, or up to about $5,200 with ipe. Joist repairs, new fasteners, and disposal can add several hundred dollars more.
- Typical cost
- $5 to $27 per square foot installed; about $1,000 to $5,200 for a 12x16 deck
- Time needed
- One to two weekends DIY; one to three days for a crew
- Skill level
- Intermediate
Key points
- Installed deck board replacement runs roughly $5 to $27 per square foot, with pressure-treated pine cheapest and ipe or PVC at the top.
- Boards are often about half the installed price; labor, tear-off, and disposal make up the rest.
- Probe the joists, rim joist, and ledger before you buy a single board, because a rotten frame turns a cheap resurfacing into a repair project.
- DIY saves roughly $3 to $8 per square foot in labor on a low, simple deck, but high or complicated decks are worth hiring out.
- Replacing old fasteners and taping joist tops adds little cost now and protects the new boards for years.
In this guide
- What Does Deck Board Replacement Typically Cost Per Square Foot?
- How Much Do Different Board Types Cost?
- What Pushes the Price Up on a Resurfacing Job?
- Should You Check the Frame Before Replacing Boards?
- What Hidden Costs Show Up Under the Old Boards?
- How Can You Save Without Cutting Corners?
- Is DIY Deck Board Replacement Worth It?
A 12x16 deck is 192 square feet, and re-boarding it over a sound frame typically lands between about $1,000 and $5,200, depending mostly on the board you pick. The frame decides whether that number holds. If the joists are rotten, a boards-only job becomes a repair project, so the sections below price both.
What Does Deck Board Replacement Typically Cost Per Square Foot?
Replacing deck boards typically costs $5 to $27 per square foot installed in 2026, with pressure-treated pine at the low end and ipe or PVC at the high end.
That covers tearing off the old boards, hauling them away, new boards, fasteners, and installation labor. If a deck board replacement cost quote looks too good to be true, check whether it includes demolition and disposal. Those can add a dollar or two per square foot on their own.
Prices swing by region. Expect the high end of every range in big metro areas. A small deck also costs more per square foot than a large one, because setup and cleanup time don't shrink with the deck.
How Much Do Different Board Types Cost?
Installed cost runs from $5 to $10 per square foot for pressure-treated pine up to $14 to $27 for ipe, with materials at roughly $2 to $15 and labor at $3 to $12 of that.
| Board type | Materials (per sq ft) | Labor incl. tear-off (per sq ft) | Installed total (per sq ft) | 12x16 deck (192 sq ft) |
|---|---|---|---|---|
| Pressure-treated pine | $2 to $4 | $3 to $6 | $5 to $10 | $960 to $1,920 |
| Cedar | $4 to $8 | $4 to $7 | $8 to $15 | $1,540 to $2,880 |
| Capped composite | $6 to $12 | $4 to $8 | $10 to $20 | $1,920 to $3,840 |
| PVC | $8 to $14 | $4 to $8 | $12 to $22 | $2,300 to $4,220 |
| Ipe or other tropical hardwood | $8 to $15 | $6 to $12 | $14 to $27 | $2,690 to $5,180 |
These are typical ranges, not quotes. Product lines vary a lot inside each category, so use the table to budget and get written bids before you commit.
For most homeowners keeping a sound frame for another 15 years or more, we'd pick capped composite. It costs roughly double pressure-treated pine up front, but you skip the staining and sealing cycle. It still needs an occasional wash. If the budget is tight or you want real wood, pressure-treated decking is the sensible choice.
What Pushes the Price Up on a Resurfacing Job?
Board material is the biggest driver, followed by deck height, layout complexity, and how much of the old deck has to come apart to reach the boards.
- Height and access. A deck 8 feet off the ground needs staging, fall protection, and slower work. Ground-level decks go fast.
- Layout. Diagonal patterns and picture-frame borders add cuts and waste. Plan on roughly 5 percent extra material for straight runs and 10 to 15 percent for diagonals.
- Railings and stairs. Working around posts and stair treads takes time, and some crews charge extra to remove and reinstall railings.
- Board length. A deck wider than your longest board needs seams, which means careful joist alignment.
- Fastening method. Decks with hidden fasteners cost more in hardware and labor than face screws.
- Small-job minimums. Some contractors set a minimum charge, so a 60-square-foot landing can cost far more per square foot than a big deck.
Should You Check the Frame Before Replacing Boards?
Yes: check the joists, rim joist, ledger, posts, and footings before you buy boards, because a boards-only job only makes sense when they're sound, and you can check most of it yourself in an hour or so.
Pull up one or two boards, or look from underneath, and run through this:
- Push a screwdriver into the top edge of several joists. If it sinks in easily or the wood crumbles, that joist is soft.
- Check where joists meet the ledger and rim joist, since water collects at joints.
- Inspect the ledger, the board that attaches the deck to the house, for gaps, rust streaks, or rot.
- Grab each post and shake it. Wobble or rot at the base points to a post or footing problem.
- Measure joist spacing. Sixteen inches on center works for most boards, but some composite and PVC products need 12 inches, so read the manufacturer's installation sheet.
If only a few joists are damaged, repair them and re-board. If rot has spread across much of the frame, or the ledger or footings are compromised, get a rebuild quote alongside the resurfacing quote. We can't give you a clean percentage for where that line falls. It depends on the deck and your local code.
What Hidden Costs Show Up Under the Old Boards?
The usual surprises are corroded fasteners, soft joists, and a damaged rim joist, which together can add anywhere from under $100 to several thousand dollars.
| Item | Typical added cost | What drives it |
|---|---|---|
| New deck screws or stainless steel screws | $50 to $200 | Deck size, coated vs stainless, hidden clip systems |
| Tape on the tops of joists | $40 to $150 | Total joist length |
| Sistering a damaged joist | $150 to $500 per joist | Joist length, access, hanger hardware |
| Rim joist replacement | $300 to $1,000 or more | Length, height, whether railing posts attach to it |
| Disposal or dumpster | $100 to $400 | Local fees, board volume |
Old fasteners first. Rusted galvanized nails and screws can weaken the grip on the joist and leave stains on new boards. Use stainless steel screws or screws rated for your board type, and for pressure-treated framing, fasteners rated for contact with the treatment chemicals.
Self-adhesive joist tape is cheap insurance. Water sits on the flat top of a joist longer than anywhere else on the deck, and that's where rot usually starts.
Sistering means fastening a new length of lumber alongside a weak joist. It works when the damage is limited and the joist still bears on solid framing at both ends. A rim joist rotted along its length is a bigger job, because railing posts and joist hangers often attach to it.
How Can You Save Without Cutting Corners?
The best savings come from doing the tear-off yourself, choosing a straight layout in standard board lengths, and fixing frame problems once instead of twice.
- Do the tear-off yourself. Pulling old boards takes a pry bar, a drill, gloves, and a free weekend. Confirm with your contractor first, then hire the install.
- Run boards straight. Boards perpendicular to the joists mean fewer cuts, less waste, and fewer labor hours.
- Order standard lengths. Measure the deck and pick lengths that minimize offcuts. Special orders cost more.
- Buy off-season. Suppliers may discount in late fall and winter, and contractors often have open schedules.
- Get itemized bids. Boards, labor, disposal, and frame repairs listed separately are easy to compare.
One saving we'd skip: mixing a few new boards into an old, weathered deck. Wood and composite both fade, so patches stand out for a year or more. Replace boards that are actually failing. If more than a few are bad, doing the whole surface looks better and often costs about the same once you count the extra trips.
Is DIY Deck Board Replacement Worth It?
Yes, on a low, simple deck under roughly 300 square feet with a healthy frame, where DIY saves about $3 to $8 per square foot in labor.
For a 12x16 pressure-treated deck, materials, fasteners, and tool rental often run $500 to $1,100, about half the installed price. Time is the other cost. Expect one to two weekends if it's your first deck.
| Situation | Recommendation | Why |
|---|---|---|
| Under 300 sq ft, low to the ground, frame sound | DIY | Simple work; mistakes are cheap to fix |
| Over 300 sq ft, ground-level | DIY tear-off, then hire the install or recruit help | Volume and cutting time add up |
| High off the ground or second story | Hire out | Fall risk, guard requirements, access |
| Joists, rim joist, or ledger need repair | Hire out the repair | Structural, often permit required |
| Ipe or other hardwood | Hire out unless experienced | Dense, needs pre-drilling, hard on tools |
A crew's labor usually runs $3 to $12 per square foot including tear-off, as the earlier table shows. You're paying for speed, proper waste handling, and someone else carrying the liability on a high deck.
For DIY you'll need a circular saw or miter saw, a drill and driver, a pry bar, a speed square, and a chalk line. Wear safety glasses, gloves, and hearing protection, plus a dust mask when cutting treated lumber, composite, or ipe. A cordless impact driver earns its keep over a few hundred screws.
Your next step: this weekend, probe the joists and rim joist with a screwdriver, then ask two or three contractors for itemized quotes that list boards, labor, fasteners, and any frame repairs separately.
Questions people ask
Do I need a permit to replace deck boards?
Swapping boards on an existing deck often doesn't need one, but rules vary by city and county. Repairs to joists, posts, footings, or the ledger commonly do, so call your local building department before you start.
Can I switch from wood to composite boards on my existing frame?
Often yes, but check joist spacing and condition first. Many composite and PVC boards need joists 12 to 16 inches on center, and the frame has to be flat and sound. Follow the manufacturer's installation instructions to keep the warranty valid.
How long do replacement deck boards last?
Pressure-treated pine often lasts 10 to 20 years depending on climate and upkeep, and cedar is similar. Composite and PVC usually carry long warranties, often 25 years or more, though fade and stain coverage differ by maker.
Is resurfacing cheaper than building a new deck?
Usually, if the frame is sound, because you keep the footings, posts, and joists, which are the costliest structural parts. If the frame needs major repair, get a rebuild quote to compare.
Should I replace the railings when I replace the boards?
Not necessarily. If the posts are solid and the railing meets current code, you can keep it. Loose or wobbly railings are worth fixing while the boards are up and the post attachments are easy to reach.
Sources and further reading
- 811 Call Before You Dig Free utility marking before any digging for footing repairs
- Cooperative Extension (extension.org) University extension guidance on home repair and wood care
Was this article helpful?