Part of our Heating and Cooling guide
Away Thermostat Temperature in Winter to Prevent Frozen Pipes
The thermostat reads your hallway, not the pipe inside the exterior wall. Here's how to set a floor and get an alert while there's time to act.
Save to PinterestWe may earn a commission when you buy through links on this page. It never changes what we recommend. Learn more
The short answer
Set the away temperature no lower than 55°F for most homes, and closer to 60°F if pipes run through exterior walls, a crawl space, or an unheated garage in a hard-freeze climate. The thermostat reads only one spot, so add a freeze alert or a remote sensor near the most exposed pipe.
- Typical cost
- $0 for settings changes; roughly $15 to $60 for a Wi-Fi temperature sensor
- Time needed
- 30 to 60 minutes before you leave
- Skill level
- Beginner
Key points
- 55°F is a floor for well-insulated homes with interior plumbing, and 58°F to 60°F is safer when pipes sit in exterior walls or crawl spaces.
- Away mode, eco settings, and geofencing can drop the temperature below the number you meant to set, so check the minimum in the settings menu.
- A thermostat freeze alert only reports the air at the thermostat, so it can miss a cold wall cavity or garage supply line.
- A remote sensor placed beside your most exposed pipe, with an alert set near 40°F, gives you the earliest useful warning.
- For trips of several days in hard-freeze weather, line up a neighbor with a key and know where your main water shutoff is.
In this guide
- Why isn't the thermostat number the whole answer?
- What temperature should you set based on where the pipes run?
- How can away mode and schedules drop below your floor?
- How do you set a safe minimum and hold on a smart thermostat?
- What do freeze alerts detect, and what do they miss?
- Do you need a remote sensor near the pipes?
- When is the house too cold to leave alone?
Set your away temperature to 55°F at the very lowest, and to 60°F if any water pipes run through exterior walls, a vented crawl space, or an unheated garage. The number only protects pipes if the thermostat can feel what the pipes feel, and it usually can't.
Why isn't the thermostat number the whole answer?
Because a thermostat measures air at one spot, usually a hallway wall, and your coldest pipe is almost never there. Water freezes at 32°F, but a supply line in a thinly insulated exterior wall can sit well below the room reading during a hard cold snap, especially with wind. How big that gap gets depends on insulation, air leaks, outdoor temperature, and how long the cold lasts.
That's why the common forum answer of 55°F isn't wrong so much as incomplete. It's a reasonable floor for a tight house with pipes on interior walls. For everything else it's thin margin.
Check where the thermostat itself sits, too. One mounted on an exterior wall or in direct sun reports skewed numbers before any of this starts.
What temperature should you set based on where the pipes run?
Use 55°F when pipes are on interior walls in heated space, and raise it to 58°F to 60°F as pipes get closer to the cold. These are our suggested starting points, not code requirements, so adjust for your climate and insulation.
| Where the pipes run | Away setting | Why |
|---|---|---|
| Interior walls, heated basement, or slab | 55°F | Surrounded by conditioned space, so the room reading is a fair proxy. |
| Kitchen or bath plumbing on exterior walls | 58°F to 60°F | Wall cavities run colder than the room. Open the cabinet doors under sinks. |
| Vented crawl space or floors over one | 60°F plus pipe insulation | Heat escapes through the floor, so insulation and sealed vents matter as much as the setpoint. |
| Garage or outbuilding supply lines | 60°F in the house, plus separate protection | House heat barely reaches them. Use heat cable rated for pipes, or have the line drained. |
| Multi-day forecasts well below 0°F | 60°F to 65°F | Long cold wears down margin. The extra heating cost is small next to water damage. |
For most cold-climate homes with at least one exposed run, we'd pick 60°F. The extra heating cost over a week is modest. ENERGY STAR publishes general thermostat setback guidance, but it's written for ordinary absences, not freeze protection, so don't borrow its numbers for a winter trip. Read your homeowners policy as well. Some require a minimum heat setting while you're away, and a claim can hinge on it.
How can away mode and schedules drop below your floor?
Away mode, eco settings, and geofencing can each apply their own lower temperature than the one you meant to set. Many smart thermostats ship with a default away range, and a phone leaving the house can trigger it with no input from you. A learning thermostat may also fold an overnight dip into its schedule.
Look for a setting called something like minimum temperature, safety temperature, or eco range, and set it to your number. Then check what happens when a vacation hold expires. If it returns to a schedule you haven't reviewed since spring, the house may cool right as a cold front arrives.
On a heat pump, also confirm that auxiliary or emergency heat is allowed at low outdoor temperatures. In deep cold the compressor alone may not hold your setpoint.
How do you set a safe minimum and hold on a smart thermostat?
Set the lowest heat temperature to your chosen number, then put a hold on it that runs a day past your return date. Work through it in this order:
- Confirm the system is in heat mode, not off, and not in a heat-cool range that lets the house drift.
- Raise the minimum heat or eco temperature to your number from the table above.
- Turn off geofenced auto-away, or confirm its temperature can't fall below your floor.
- Start a hold through the day after you return.
- Turn on a low temperature alert, covered in the next section.
- Change the setpoint from the app and watch for the furnace to respond. That proves the thermostat is online.
What do freeze alerts detect, and what do they miss?
A smart thermostat freeze alert detects when the air at the thermostat falls below a threshold you pick, and it misses cold that stays local to a pipe. If the hallway reads 48°F, you'll hear about it. If a garage line is freezing while the hallway reads 58°F, you won't.
Set the notification roughly 10°F below your away setting, around 45°F to 50°F, so it fires while the house is cold but not yet dangerous. Then check the points that can silence it:
- Phone notifications are muted, or Do Not Disturb is on while you're traveling across time zones.
- The thermostat loses power or Wi-Fi. Models without a steady power source, such as a C-wire, may drop offline.
- Nobody can act on the alert. A warning only helps if someone with a key can get there.
Turn on the thermostat's offline notification too, if it has one. A silent thermostat during a storm is information.
Do you need a remote sensor near the pipes?
Yes, if pipes run through a crawl space, garage, or exterior walls and you'll be gone more than a couple of days in freezing weather. A remote sensor placed beside the most exposed pipe reports what the pipe actually sees. Wi-Fi units commonly run about $15 to $60, and Zigbee or Matter sensors work too if you already have a hub. The Connectivity Standards Alliance publishes the Matter standard if you want to check compatibility.
Place it on or next to the pipe, not on a warm floor or beside a heat vent. Under a sink on an exterior wall, leave the cabinet door open so the sensor and pipe both feel the room. Set its alert near 40°F. That's close enough to freezing to matter and far enough off to leave time to call someone.
For longer trips in a cold climate, add backup steps. Put pipe insulation on exposed runs. Use heat cable on garage or crawl space lines only if it's rated for the pipe material and installed to its instructions, and have an electrician add an outlet if you don't have a safe one nearby. Shutting off the main and draining the system is the most dependable choice for long absences. Have a plumber do it if you're unsure, since homes with fire sprinklers or hydronic heating need different handling. A water shutoff valve with leak sensors, often several hundred dollars or more installed, can limit damage if something does burst.
When is the house too cold to leave alone?
Treat any thermostat reading below about 45°F, or any sensor near a pipe reading close to 35°F, as a call-someone-now situation. Don't wait to see if it recovers.
Call your neighbor first, then a plumber or heating contractor if the furnace has failed. If anyone smells gas, they should leave the house and call the gas utility or 911 from outside. If a pipe has already burst, shutting off the water main comes first and a plumber second.
Before you leave, pick your floor from the table, lock it into the thermostat, and text a neighbor your return date and the main shutoff location.
Questions people ask
Is it cheaper to turn the heat off completely while I'm away?
It can look cheaper for a few days, but one burst pipe costs far more than a week of low heat. Leave the heat on at your chosen floor. If you want to shut the house down, shut off the main water and have the lines drained.
How cold can a house get before pipes freeze?
There's no single indoor temperature, because freezing depends on the pipe's location, insulation, wind, and how long the cold lasts. Air in the 40s usually isn't an immediate threat, but pipes in exterior walls or crawl spaces can freeze while the room reads above 32°F. Location matters more than any one number.
Should I leave a faucet dripping while I'm gone?
Dripping is mainly a tactic for cold snaps when you're home to watch it, and it won't help if the heat fails. For longer trips, shutting off the main and draining the lines is more dependable.
Will my smart thermostat warn me if the power goes out?
Usually it can't, because it loses power and Wi-Fi at the same time. Some models send an offline notification after a set time, so turn that on. A battery-powered sensor that alerts through its own connection gives you a second chance at a warning.
Do I need to shut off the water main if the thermostat is set to 60°F?
For a few days in mild cold, a 60°F setting with insulated pipes is often enough. For a week or more in hard-freeze weather, shutting off the main adds a layer that doesn't depend on power, Wi-Fi, or your furnace.
Sources and further reading
- ENERGY STAR General thermostat and energy-saving guidance, including setbacks
- Connectivity Standards Alliance (Matter) Matter standard info for checking sensor and thermostat compatibility
Was this article helpful?