Part of our Heating and Cooling guide
Smart Thermostat Mounting Mistakes That Skew Readings
Exterior walls, supply registers, hallways and kitchens all feed your thermostat bad data. Here's how to spot them and what to do instead.
Save to PinterestWe may earn a commission when you buy through links on this page. It never changes what we recommend. Learn more
The short answer
Mount a smart thermostat on an interior wall about five feet off the floor (manufacturers commonly say 52 to 60 inches), in a room you actually use. Keep it away from supply registers, return grilles, sunlight, kitchens, fireplaces and exterior walls. Tape a second thermometer to the spot for 24 hours first. If the spot can't be fixed, add a remote sensor.
- Typical cost
- $10 to $30 for test thermometers; $30 to $80 per remote sensor; about $150 to $400 to have wiring relocated
- Time needed
- About 30 minutes to mount, plus a 24-hour test
- Skill level
- Beginner
Key points
- Exterior walls, airflow from a supply register or return grille, and nearby heat sources are the biggest causes of wrong readings and short-cycling.
- Hallways, stairwells and entries rarely match the temperature of the rooms where you spend your time.
- Taping a second thermometer to the planned spot for 24 hours costs a few dollars and catches most bad locations before you drill.
- Mount the unit about five feet off the floor and plug the wire hole so wall-cavity drafts don't reach the sensor.
- When the thermostat can't move, a remote sensor lets the system read the room you care about.
In this guide
- Why does thermostat location change what the system does?
- Is it a mistake to mount a thermostat on an exterior wall?
- Why shouldn't a thermostat sit near a supply vent or return grille?
- Are hallways, stairwells and entries good places for a thermostat?
- Which heat sources throw off a smart thermostat?
- Does mounting height and airflow around the unit matter?
- How do you test a spot before you drill?
- When does a remote sensor fix the problem?
Your thermostat doesn't measure your house. It measures the few cubic feet of air around itself, and every mistake below is a way of making that air unrepresentative. Get the spot wrong and a $100 to $300 smart thermostat behaves like a bad old dial, heating or cooling for a wall nobody sits near.
Why does thermostat location change what the system does?
The thermostat starts and stops your furnace, heat pump or air conditioner based on one reading, so a spot that runs warm or cold makes the whole system run wrong. If the unit reads 4 degrees colder than your living room, the heat runs long and the house overheats. If it reads warm, the AC quits early and the bedrooms stay muggy.
The sneakier failure is short-cycling. Moving air or a heat source hits the sensor, the reading jumps within minutes, and the equipment shuts off before the rest of the house has caught up. Then it starts again. Frequent cycling adds wear to blower motors and compressors. ENERGY STAR publishes guidance on thermostat savings, and every one of those savings assumes the unit reads a representative temperature. Schedules and away modes only save what the sensor lets them.
Is it a mistake to mount a thermostat on an exterior wall?
Yes, because the wall surface and the air behind it track outdoor temperature instead of room temperature. In January the wall runs cold, so the thermostat reads low and keeps the heat on. In July a sun-baked wall reads high and the AC overworks.
The same goes for any wall shared with an unheated garage, attic knee wall or crawlspace. People often reuse the old spot because the wire is already there, and the cost is a thermostat that seems to misbehave mainly on the coldest and hottest days. Pick an interior partition wall instead. If you can't, run the test below and expect to need a remote sensor.
Why shouldn't a thermostat sit near a supply vent or return grille?
A thermostat near a supply register or return grille samples moving air instead of room air, so its readings swing fast and the system cycles on and off. Above a supply register, warm air from the furnace rises straight onto the unit. It reads satisfied after a few minutes and cuts the heat while the room is still cool. In summer the same spot reads cold from the AC stream and shuts the cooling off early.
Beside a return grille, the unit reads air being pulled across the house, which lags behind what you feel in the room. Give it clear space on every side. And if the old thermostat was in a bad place, don't copy it just because the wire is there.
Are hallways, stairwells and entries good places for a thermostat?
Usually not, because they reflect the temperature of a transit space and not the rooms where you spend your time. Stairwells act like chimneys: warm air climbs, so a unit at the bottom tends to read cool and one at the top tends to read hot. Entries get a blast of outdoor air every time the door opens. A hallway with closed doors at both ends and no vents can sit a few degrees off from your living room.
Choose a central interior wall in the room you use most hours of the day. For most two-story homes with one thermostat, we'd pick the main-floor living area and handle the upstairs with a remote sensor rather than hunting for a compromise spot in the stairwell.
Which heat sources throw off a smart thermostat?
Ovens, lamps, TVs, fireplaces and direct sunlight all add heat that the thermostat mistakes for room temperature. Sun is the one everyone knows, but sun moves. A wall that's shaded in October can get low winter sun for hours in December, so check the spot across seasons and not just on install day.
The kitchen is the other repeat offender. A thermostat on the far side of a range wall, or across from the oven, reads high every evening at dinner and the system fights the cooking. A fireplace on the other side of the wall, an incandescent lamp or a TV on a shelf below the unit does the same at smaller scale. The result is a cooler house at night, because the thermostat believes the room is warm.
| Mistake | What the thermostat reads | What you notice |
|---|---|---|
| Exterior or cold wall | Too low in winter, too high in summer | Overheated or overcooled rooms on extreme days |
| Above a supply register | Fast jumps right after the system starts | Short cycles, rooms that never quite get there |
| Hallway or stairwell | Transit-space temperature | Living room and bedrooms off by several degrees |
| Near kitchen, lamp or fireplace | Too high at certain hours | Cold rooms in the evening, AC running hard |
| Direct sun | Too high for a few hours a day | Cooling cycles that start for no clear reason |
Does mounting height and airflow around the unit matter?
Yes, a thermostat should sit about five feet off the floor with open air around it, because a unit mounted too low or boxed in reads dead air instead of the air you breathe. Manufacturers commonly specify about 52 to 60 inches to the center of the unit, so check your model's instructions. Don't tuck it behind a swinging door, inside a bookshelf nook or behind a curtain.
Then there's the hole. The opening for the thermostat wire often connects to a cavity that runs to the attic or basement, and air moves through it. That draft crosses the back of the unit and makes the reading drift. Plug the opening behind the wall plate with a small wad of fiberglass insulation or non-hardening putty.
How do you test a spot before you drill?
Tape a digital thermometer to the planned spot, tape a second one at the same height in the room you use most, and compare readings over 24 hours. Use painter's tape so you don't peel paint. It's the cheapest step in this guide, and it settles arguments.
- Place both thermometers about five feet off the floor, out of direct sun.
- Write down both readings in the morning, afternoon, evening and just after the system turns on.
- Look at the gap and at how fast the numbers move. A steady gap of a degree or two is normal, and many thermostats let you offset it. Swings of several degrees, or jumps right when the system starts, mean you should pick a different wall.
If the best wall has no wiring, you're relocating thermostat wire. An HVAC technician or electrician will typically charge about $150 to $400 for that, depending on how hard the wall is to fish. While the wall is open, find out whether your system has a C-wire, since many smart thermostats need one.
When does a remote sensor fix the problem?
A remote sensor fixes the problem when the thermostat can't move, because it lets the system read temperature in a room you care about instead of the wall the thermostat is stuck on. Many brands sell one for roughly $30 to $80 each, and some thermostats include one or two in the box.
Compatibility is the catch. Sensors usually pair only with the maker's own thermostats, and some thermostats don't support sensors at all. Matter, the smart home standard overseen by the Connectivity Standards Alliance, covers how devices talk to your smart home setup. It doesn't mean a thermostat will accept another brand's sensor, so confirm in the manufacturer's compatibility list before you buy.
Place the sensor on an interior wall or shelf at about five feet, in the bedroom or living room, and keep it clear of the same hazards: vents, sun, lamps and exterior walls. If your model lets you choose which sensor is active by time of day, use the bedroom sensor at night and the living room sensor during the day.
Next step: tape two thermometers up tonight, read them tomorrow, and only then pick up the drill.
Questions people ask
How far should a smart thermostat be from a window?
There's no single code number, so follow your model's instructions. In practice, keep it out of any spot that gets direct sun or a draft from the window at any time of year, which usually means several feet of distance.
Can I move my thermostat to a different wall myself?
With a low-voltage system, many homeowners can, if they shut off the breaker first and are comfortable fishing wire through a wall. If your system is line voltage, or the wall has fire blocking or plaster that makes running wire difficult, hire a licensed pro.
Does the thermostat need to be in the middle of the house?
No, it needs to be in a room that represents where you spend your time. A main-floor living area on an interior wall usually beats a geometric center that happens to be a hallway.
Will a remote sensor help if my thermostat is on an exterior wall?
Yes, on models that support sensors, because the system can use the sensor's reading instead of, or averaged with, the thermostat's own. Confirm your model supports it and set the sensor as active in the app.
Why does my new smart thermostat cycle on and off every few minutes?
Bad placement is a common cause, especially a spot over a supply register or beside a heat source. Equipment problems and settings can also be to blame, so put a second thermometer at the same spot and see whether the reading jumps when the system starts.
Sources and further reading
- ENERGY STAR General guidance on thermostats and home energy savings
- Connectivity Standards Alliance (Matter) Background on what the Matter standard covers for smart home devices
Was this article helpful?