Oven Igniter Replacement Cost in 2026: Parts and Labor
The part is cheap. The diagnosis, and the safety valve or control board hiding behind it, is where bills double.
Save to PinterestWe may earn a commission when you buy through links on this page. It never changes what we recommend. Learn more
The short answer
Oven igniter replacement cost is typically $150 to $350 with a technician, or $20 to $100 if you do it yourself. The igniter itself usually runs $20 to $100; the service call and labor make up the rest. If the igniter tests fine, the real fault may be a safety valve or control board, which can push the bill to between $200 and $650.
- Typical cost
- $150 to $350 with a pro; $20 to $100 DIY
- Time needed
- 30 to 60 minutes for the swap
- Skill level
- Intermediate
Key points
- A technician usually charges $150 to $350 total to replace a gas oven igniter, while the part alone is typically $20 to $100.
- Hot-surface igniters, the most common type, are the cheapest fix; spark systems can add a module that costs $60 to $200.
- Electric ovens have no igniter; a dead electric oven usually needs a bake element, typically $125 to $300 installed.
- A multimeter check with the gas and power off can tell you whether the igniter is dead before you pay a diagnostic fee.
- If a good igniter still won't light the burner, the oven safety valve or control board is the likely culprit, and the repair can run $200 to $650.
In this guide
- What Does an Oven Igniter Do, and How Does Each Type Fail?
- How Much Does Oven Igniter Replacement Cost by Type?
- What Pushes the Price Up or Down?
- What If the Igniter Tests Fine but the Oven Still Won't Heat?
- How Do You Check an Oven Igniter with a Multimeter?
- How Can You Save on Igniter Repair Without Risking Safety?
- Should You Replace the Igniter Yourself or Hire a Technician?
Budget $150 to $350 for a technician to swap a gas oven igniter, or $20 to $100 if you buy the part and do it yourself. Most of a pro bill is the service call and labor, not the part. The catch is that the igniter isn't always the problem, and that is where a $200 repair turns into a $450 one.
What Does an Oven Igniter Do, and How Does Each Type Fail?
A gas oven igniter is an electrically heated part that glows until it draws enough current to open the gas safety valve, then lights the burner. When it weakens, it still glows but never pulls enough current, so the valve stays shut and the oven never heats.
Most modern gas ovens use a hot-surface igniter: a flat, ceramic-looking part made of silicon carbide or the tougher silicon nitride. It's brittle. Wear shows up as a longer and longer wait before the burner lights, then no light at all. Older ovens use a rod-shaped glow bar that works the same way and fails the same way, and parts counters price the two about alike.
The other style is a spark igniter, an electrode that clicks to light the gas, driven by a spark module. A worn electrode or failed module shows up as clicking with no flame.
Electric ovens don't have an igniter at all. If you searched for electric oven igniter replacement cost, you almost certainly need a new bake element, which is priced in the table below.
How Much Does Oven Igniter Replacement Cost by Type?
Most igniter repairs with labor land between $150 and $325, and a failed spark module can push the total to around $450. These are typical U.S. ranges, and your local rates and brand will move them.
| Repair | Part price | Pro labor and call | Typical pro total | DIY total |
|---|---|---|---|---|
| Hot-surface or glow-bar igniter (gas oven) | $20 to $100 | $100 to $200 | $150 to $300 | $20 to $100 |
| Spark electrode only | $25 to $90 | $100 to $225 | $150 to $325 | $25 to $90 |
| Spark module (ignition box) | $60 to $200 | $100 to $225 | $200 to $450 | $60 to $200 |
| Bake element (electric oven) | $25 to $100 | $100 to $200 | $125 to $300 | $25 to $100 |
A generic hot surface igniter sits at the low end, and the job is quick, often under an hour. Prices climb toward $100 for some name-brand parts.
What Pushes the Price Up or Down?
Five things move the bill: the part source, the ignition type, how hard the part is to reach, your local labor rate, and whether the technician finds a second fault.
Brand-name (OEM) parts cost more than aftermarket parts, sometimes double. Premium and dual-fuel ranges can have pricier igniters and extra ignition parts. Access matters too. On many ranges the igniter sits behind the bottom panel and burner baffle, and the job takes minutes. On others you remove a rear panel or slide the range out first. If you do pull the range, move it gently so you don't strain the gas connector, and put the anti-tip bracket back when you're done.
The service call fee is the part many people don't plan for. It typically runs $75 to $150 and is often credited toward the repair if you go ahead, though policies vary, so ask when you book. Metro areas and after-hours calls cost more.
Age is the last factor. A basic new gas range often starts under $1,000, so a $200 igniter repair is almost always worth doing. Once a repair approaches half the price of a comparable new range and the oven is well past a decade old, price a replacement.
What If the Igniter Tests Fine but the Oven Still Won't Heat?
If the igniter glows bright and checks out electrically but the burner never lights, the fault is usually the oven safety valve, the control board, or a temperature sensor. These repairs can double the bill because the parts cost more and the diagnosis takes longer.
| Actual fault | Part price | Typical pro total |
|---|---|---|
| Temperature sensor | $15 to $60 | $120 to $250 |
| Oven safety valve | $50 to $200 | $200 to $450 |
| Control board | $100 to $400 | $275 to $650 |
The safety valve is the part the igniter's current has to open. A valve that has gone weak won't open even with a healthy igniter. A failed control board may never send power to the igniter, so you'll see no glow at all while the igniter measures fine.
Two clues help. If the stovetop burners light normally, the gas supply to the range is probably fine and the problem is oven-specific. If the igniter glows for a minute or more and the burner never ignites, suspect a weak igniter first and the valve second. That's why testing the igniter comes before any parts shopping.
How Do You Check an Oven Igniter with a Multimeter?
A digital multimeter set to ohms can tell you in about five minutes whether the igniter circuit is open, which can save you a diagnostic fee. It has limits: a cold reading can pass on an igniter that fails once it heats up.
- Turn off the gas shutoff valve to the range, then unplug the range or switch off its breaker. Let the oven cool completely.
- Remove the oven racks, the bottom panel, and the burner baffle to expose the igniter.
- Disconnect the igniter's wiring plug. Don't pull on the wires, and handle the igniter gently, since it cracks easily.
- Set the meter to ohms (a 200 or 2,000 ohm range on most meters) and touch one probe to each terminal.
- Read the result. An open or infinite reading, often shown as OL, means the igniter is broken and needs replacing.
Resistance specs vary by model and by igniter material, so compare your reading to the figure listed for your part number. A reading far above that spec suggests a weak igniter. If it reads normally, time how long it takes to glow when you test the oven. A long delay, or a dim orange glow instead of a bright one, points to a weak igniter even with a passing reading.
How Can You Save on Igniter Repair Without Risking Safety?
The biggest saving is doing the swap yourself, which typically cuts a $150 to $350 repair to $20 to $100. If you hire out, a few moves still trim the total.
- Test the igniter first, so you know whether you're buying a part or paying for a service call to find out.
- Ask whether the service call fee is credited toward the repair when you book.
- Compare OEM and aftermarket prices for the same model number. Many aftermarket parts fit fine, but buy from a reputable seller that lists your exact model, and look for a safety certification mark such as UL where one applies. UL Solutions explains what those marks mean.
- Check your range model against recall notices at the U.S. Consumer Product Safety Commission. Recalls vary, but some range recalls involve gas controls and offer free repairs.
- Skip cheap used igniters. They have already lost part of their life.
Don't try to save money by lighting the oven with a match while the igniter is dead. Gas can build up in the cavity before it lights, and that's how a flash fire starts.
Should You Replace the Igniter Yourself or Hire a Technician?
Swapping a hot surface igniter or spark electrode is a reasonable DIY job, but anything that opens a gas line or involves the control board should go to a pro. The igniter job is electrical connectors and a couple of screws, with no gas fittings touched.
We'd pick DIY for the most common case: a gas oven that won't heat, with an igniter that measures open or glows weakly. Do the multimeter check, buy the part by model number, and work with the gas and power off.
Call a technician when the igniter tests fine, when the oven has a gas smell, when the valve is the suspect, or when the control board shows error codes. Local code may also require a licensed professional for any gas connection work, so check before you start.
Your next step: find the model tag, run the ohms check, and write down the reading before you pick up the phone.
Questions people ask
Can I use a universal oven igniter?
Universal igniter kits exist and can work, but they often need matching connectors or some wiring changes. A part matched to your model number is the safer, simpler choice. If you go universal, confirm the kit lists your range model.
How long does an oven igniter last?
Lifespan varies widely with the part and how often you bake. Some last a few years, others a decade or more. A longer and longer delay before the burner lights is the usual warning sign.
Why does my gas oven click but not light?
Clicking points to a spark ignition system. The electrode may be dirty or worn, the spark module may be failing, or gas may not be reaching the burner. Cleaning the electrode tip is a low-cost first step, and persistent clicking with no flame calls for a technician.
Is it safe to keep using an oven with a weak igniter?
A weak igniter usually just delays or prevents the burner from lighting, but a slow, noisy ignition or any gas smell is a reason to stop using the oven. Turn it off, ventilate the room, and call a technician. Don't keep retrying if you smell gas.
Can I cook while I wait for the replacement part?
Use the stovetop, a toaster oven, or a countertop appliance instead. Don't light a gas oven with a match as a workaround, because gas can collect in the cavity before it ignites.
Sources and further reading
- U.S. Consumer Product Safety Commission Check your range model for recalls and gas appliance safety guidance.
- UL Solutions Background on safety certification for appliances and replacement parts.
Was this article helpful?