Dryer Heating Element Replacement Mistakes to Avoid
A dead element is only one of three parts that cause no heat, and skipping the tests is how one repair turns into two.
Save to PinterestWe may earn a commission when you buy through links on this page. It never changes what we recommend. Learn more
The short answer
If your electric dryer runs but doesn't heat, unplug it and test the heating element, thermal fuse, and high-limit thermostat with a multimeter before buying anything. A healthy element often reads roughly 10 ohms (check your model's spec), while a good fuse or thermostat reads near zero. Replace only the failed part, then clear the clogged vent that probably caused it.
- Typical cost
- $5 to $80 in parts; a pro repair visit typically runs $150 to $400, depending on region and part
- Time needed
- 1 to 2 hours
- Skill level
- Intermediate
Key points
- Three different parts cause the same no-heat symptom, so test all three before ordering a heating element.
- Unplug the dryer before you open it, because switching it off at the control doesn't cut power to the terminal block.
- Replace scorched terminals and brittle wire ends, or the new element can overheat at the connection.
- A blown thermal fuse almost always means the dryer overheated, so clean the vent before you power it back up.
- Match the element to your dryer's model number and voltage rather than to how the old one looks.
In this guide
- Mistake 1: Replacing the heating element without testing it
- Mistake 2: Assuming the thermal fuse and high-limit thermostat are fine
- Mistake 3: Skipping the power safety steps before pulling the panel
- Mistake 4: Reusing burned or brittle wire terminals on the new element
- Mistake 5: Ignoring the clogged vent that caused the failure
- Mistake 6: Buying the wrong element for your model and voltage
- When should you call a pro instead?
Put a multimeter on three parts before you order a heating element: the element, the thermal fuse, and the high-limit thermostat. Any of them can leave you with an electric dryer not heating, and the element is the part many people buy first, whether it failed or not. These six mistakes are how a cheap fix becomes a second repair.
Mistake 1: Replacing the heating element without testing it
Replacing the element without a continuity test is the most common mistake, because a coil can fail with no visible break and a good one can look scorched. A replacement commonly runs $30 to $80 depending on the model, so a guess gets expensive.
Start at the panel, not the dryer. If the drum spins but there's no heat, one half of the double-pole breaker may have tripped while the other half keeps the motor running. That gives you a dryer that runs but has no heat and a fully working element. Flip the breaker fully off and back on before you open anything.
Then test the part. With the dryer unplugged, pull the wires off the element's two terminals and set a digital multimeter to ohms. Touch one probe to each terminal. A healthy element often reads somewhere around 10 ohms, though your model's spec may differ. A reading of OL or infinity means the coil is open and the element is dead. Next, touch one probe to the metal housing and the other to a terminal. Any reading other than OL means the coil is shorted to the case.
Mistake 2: Assuming the thermal fuse and high-limit thermostat are fine
A blown thermal fuse or a failed high-limit thermostat cuts power to the element and looks just like a dead element. Both open when the dryer runs too hot, and both take a minute to test.
| Part | Good reading (unplugged) | Typical part cost |
|---|---|---|
| Heating element | Roughly 10 ohms; check your model's spec | $30 to $80 |
| Thermal fuse | Near 0 ohms | $5 to $25 |
| High-limit thermostat | Near 0 ohms at room temperature | $10 to $40 |
Replacing a thermal fuse is a like-for-like swap with the exact part for your model. Never jump across it to get heat back, because it exists to stop a fire. The fuse is also a symptom: it blew because the dryer overheated, which leads to mistake 5.
Mistake 3: Skipping the power safety steps before pulling the panel
Unplug the dryer from the wall before you touch anything, because the 240-volt terminal block stays live while the cord is plugged in. Switching the dryer off at the control doesn't change that.
Dryers don't usually carry a large capacitor the way a microwave does, but control boards can hold a charge briefly, so wait several minutes after unplugging. Touch bare metal on the cabinet before you reach for wires. Wear gloves, since the sheet-metal edges inside cut easily. Photograph the wiring before you pull a single connector.
Mistake 4: Reusing burned or brittle wire terminals on the new element
Reusing a scorched terminal can destroy a new element, because a loose or corroded connection creates resistance and heat right where the wire attaches. If the old terminal looks blackened, or the insulation cracks when you flex it, replace it.
Use high-temperature ring terminals and cut back to clean copper, or buy the wiring repair kit sold for your model. Tighten the connections snug, but don't crank down on the ceramic insulators, which crack. A poor connection can cost you a second element. Worse, it's how a repair turns into a fire hazard.
Mistake 5: Ignoring the clogged vent that caused the failure
A clogged dryer vent is the usual reason elements, fuses, and thermostats fail in the first place. When air can't leave, the cabinet overheats and the safety parts trip or burn out.
Clean the lint trap, then disconnect the duct and clear it from the dryer to the outside flap with a vent brush kit. Replace crushed foil or vinyl with rigid metal duct, which resists crushing and traps less lint. Maximum duct length and routing depend on your dryer's manual and local code, so check both. The U.S. Consumer Product Safety Commission publishes dryer fire safety information, and the Department of Energy's Energy Saver site covers lint and vent upkeep.
Mistake 6: Buying the wrong element for your model and voltage
The wrong element can fit the cabinet and still not match your dryer's wattage, voltage, or mounting, so order by model number and not by appearance. You'll find the model number on the tag inside the door frame or on the back panel.
Residential electric dryers run on 240 volts, and elements draw several thousand watts, with ratings that vary by model. Pull up the manufacturer's parts diagram and match the part number. Universal kits can work, but confirm the specs first. Check the return policy too, since some sellers won't take back electrical parts once they're installed.
When should you call a pro instead?
Call a pro if all three parts test good, if the outlet or breaker is the problem, or if you see melted wiring at the terminal block. A repair visit typically costs $150 to $400, depending on your area and the part.
Gas dryers are a different job. The heat comes from a burner and igniter, so any gas-line or valve work belongs to a licensed technician. If your dryer is old and needs a second major repair, compare that bill against a replacement.
Tonight, unplug it, pull the panel, and test the element, thermal fuse, and high-limit thermostat before you order anything.
Questions people ask
Why does my dryer tumble but not heat when the element tests good?
The usual culprits are a blown thermal fuse, a failed high-limit thermostat, or a half-tripped double-pole breaker. A faulty cycling thermostat or control board can also cut heat. Test those parts in order before replacing anything.
Can I bypass a blown thermal fuse to get my dryer working?
No. The fuse is a one-time safety device that opens when the dryer overheats, and bypassing it removes the protection against a fire. Replace it with the exact part for your model and fix the cause of the overheating.
How long does it take to replace a dryer heating element?
Most DIYers need one to two hours, including pulling the dryer out, removing the panel, and testing parts. The time varies by model, because some access the element from the back and others from the front.
Is it worth fixing an older dryer with a bad heating element?
Often yes, since the parts are inexpensive and the repair is straightforward. It makes less sense if the dryer needs several repairs or has a history of vent problems, because the repair bill can approach the cost of a new machine.
Do these tests work on a gas dryer?
Only partly. A gas dryer still has a thermal fuse and high-limit thermostat you can check, but it has no electric heating element. Anything involving the igniter, gas valve, or gas line should go to a licensed technician.
Sources and further reading
- U.S. Consumer Product Safety Commission Consumer product safety guidance, including dryer fire hazards
- U.S. Dept. of Energy, Energy Saver Dryer efficiency tips, including lint filter and vent maintenance
Was this article helpful?