Fix and Furrow
Advertise

Wood Movement: How Much Solid Wood Shifts and How to Plan

A simple formula turns shrinkage percentages into inches, so you can size gaps and slots before the wood decides for you.

Save to Pinterest

We may earn a commission when you buy through links on this page. It never changes what we recommend. Learn more

Close view of a solid walnut tabletop showing board edges and grain
Photo: simon on Unsplash

The short answer

A flatsawn hardwood board 12 inches wide typically changes about 0.1 to 0.2 inch across its width over a 5-point swing in moisture content. Estimate yours with width × tangential shrinkage percent × moisture change ÷ 3,000. Then let the wood move with floating panels, slotted screw holes or breadboard ends, or choose plywood where no movement is acceptable.

Typical cost
$25 to $100 for a pin-type moisture meter; fasteners and hardware usually add $10 to $30
Time needed
About 15 minutes to run the numbers for a project
Skill level
Beginner

Key points

  • Solid wood moves mostly across its width and barely at all along its length.
  • Multiply board width by the species' tangential shrinkage percent and the expected moisture swing in points, then divide by 3,000 to get inches of movement.
  • A 36-inch flatsawn walnut tabletop can change about 1/2 inch in width across a 5-point moisture swing, so screwing it down rigidly invites splits.
  • Wide door panels need roughly 1/8 inch of room per side in the groove, and tabletops need slotted holes or figure-8 fasteners so they can slide.
  • Hardwood plywood is the better choice when the design can't tolerate any movement.
In this guide
  1. What Is Wood Movement?
  2. Why Does Wood Move Across the Grain and Not Along It?
  3. How Much Do Common Species Shrink and Swell?
  4. How Do You Estimate Movement for Your Board Width?
  5. How Do You Build a Tabletop or Door That Lets Wood Move?
  6. When Is Solid Wood the Wrong Choice?
  7. What Should You Do Before You Build or Buy?

A flatsawn red oak board 12 inches wide changes by about 0.17 inch when its moisture content swings 5 points, which is plausible between a humid August and a dry, heated January. That's the scale to design around. It's enough to crack a tabletop that's screwed down tight.

What Is Wood Movement?

Wood movement is the swelling and shrinking of lumber as it gains and loses moisture from the surrounding air. A board is never fully stable after it's dried. It keeps trading moisture with your house, taking it on in humid months and giving it up when the furnace runs.

The amount depends on the species, how the board was cut, and how big your seasonal humidity swing is. In most heated U.S. homes, furniture-grade wood settles around 6 to 9 percent moisture content, higher in damp coastal climates and lower in dry ones. The USDA Forest Products Laboratory's Wood Handbook has equilibrium moisture content tables if you want a figure for your area.

Why Does Wood Move Across the Grain and Not Along It?

Wood moves mostly across the grain because the cell walls swell in thickness while the long fibers barely change in length. A 60-inch board moves only a hundredth or two of an inch end to end. A 12-inch-wide flatsawn board moves roughly ten times that across its width.

Across the grain, direction matters. Tangential movement runs along the growth rings, which is the width of a flatsawn board. Radial movement runs across the rings, which is the width of a quartersawn board. Tangential is often about twice radial, so quartersawn stock commonly moves about half as much.

How Much Do Common Species Shrink and Swell?

White oak and hard maple move the most of the six species below, while cherry, walnut, and eastern white pine move less. The table uses rounded green-to-dry shrinkage figures from the USDA Wood Handbook, then shows the result for a 12-inch board over a 5-point moisture swing.

SpeciesTangential %Radial %Flatsawn, per 12 in.Quartersawn, per 12 in.
Red oak8.64.00.17 in.0.08 in.
White oak10.55.60.21 in.0.11 in.
Hard maple9.94.80.20 in.0.10 in.
Black cherry7.13.70.14 in.0.07 in.
Black walnut7.85.50.16 in.0.11 in.
Eastern white pine6.12.10.12 in.0.04 in.

Treat these as planning estimates. Individual boards vary, and your real number depends on your home's humidity swing. If stability is the goal, quartersawn white oak is a solid pick, though it costs more per board foot than flatsawn stock.

How Do You Estimate Movement for Your Board Width?

Multiply the board's width in inches by the tangential shrinkage percent and by the moisture change in points, then divide by 3,000. The 3,000 comes from wood reaching full shrinkage somewhere around 30 percent moisture, so each point of change moves it about 1/30 of the listed percentage.

Take a 36-inch-wide walnut tabletop glued up from flatsawn boards, in a house that swings from 6 to 11 percent moisture:

  1. Width × shrinkage × swing: 36 × 7.8 × 5 = 1,404.
  2. Divide by 3,000: about 0.47 inch of total movement.

Fix that top at its center and each edge moves roughly 1/4 inch. Real tops often move a bit less, since glued-up boards rarely all run flatsawn, but plan for the worst case. A 12-inch cherry door panel works out to 12 × 7.1 × 5 ÷ 3,000, or about 0.14 inch total.

How Do You Build a Tabletop or Door That Lets Wood Move?

You build for movement by never rigidly fixing a wide cross-grain surface to a part that doesn't move with it. Three methods cover most projects.

  • Tabletop fasteners: figure-8 fasteners, Z-clips, or wood cleats with slotted screw holes attach the top to the aprons while letting it slide. Orient slots across the grain and size each one for the movement at that screw's distance from the fixed center, plus the screw diameter.
  • Floating panel doors: cut the groove about 3/8 inch deep and leave roughly 1/8 inch of clearance per side on wide panels; narrow ones need less. Don't glue the panel into the frame. A small dab of glue at the center of the top and bottom edges keeps it centered, and some builders use rubber spacer balls instead.
  • Breadboard ends: these cap the ends of a tabletop and help keep it flat. Many builders glue only the center few inches of the tongue and fasten the rest with pins in elongated holes, so the top can expand beneath the ends.

Finish matters too. Coat every surface evenly, including the underside, so moisture enters and leaves at a similar pace. Finish slows moisture exchange but never stops it, so the movement allowances still apply.

When Is Solid Wood the Wrong Choice?

Solid wood is the wrong choice when the design can't tolerate any gap, crack, or sliding joint. Examples include a wide panel set tightly between fixed walls or a built-in with flush inset doors.

Hardwood plywood and veneered panels move very little, because the cross-laminated layers restrain each other. A plywood door panel or table core with solid wood edging often holds up better in a kitchen, bathroom, or basement. We'd pick solid wood for most tabletops, since you can sand out scratches for decades. For large cabinet panels where stability matters more, we'd choose plywood.

What Should You Do Before You Build or Buy?

Measure your lumber's moisture content, run the formula for your widest board, and choose the joinery before you cut anything. If the movement comes out under about 1/16 inch, ordinary construction is usually fine. Above 1/8 inch, plan for slotted fasteners, floating panels, or plywood.

Let boards acclimate in the room where the piece will live for a week or two, then check them again. Buying a finished table? Look underneath for cleats, figure-8 fasteners, or slotted holes. Tops screwed down through plain round holes are the ones that split.

Questions people ask

How long should lumber acclimate before I build?

One to two weeks, stacked with spacers in the room where the piece will live, is typical for kiln-dried lumber. Check with a moisture meter. If readings stop changing and sit near 6 to 8 percent, you're ready.

Why did my solid wood tabletop crack?

Most often the top was fixed rigidly to aprons or a base running across the grain, so winter shrinkage had nowhere to go. The wood then splits along a weak glue line or a growth ring. Slotted holes or tabletop fasteners prevent a repeat.

Do old tables stop moving?

No. Solid wood responds to humidity for its whole life, though a table can seem stable if your home's humidity stays steady. Dry winter heating and humid summers keep nudging the boards.

Can I fix a gap that opened in a glued-up top?

Small gaps can be filled with colored filler or a thin wood sliver if you accept some further seasonal movement. Large ones usually mean re-gluing the top or rebuilding it with narrower boards and proper attachments.

Does plywood move at all?

Very little across its face, because the alternating layers hold each other in check. Edges and thickness still respond to humidity, and plywood can swell badly if it gets wet, so seal exposed edges in kitchens and baths.

Sources and further reading

Elsewhere in Workshop