Part of our Home Repair Troubleshooting guide
Planer Snipe: Why Boards Dip at the Ends and How to Fix It
A checklist in the order to test it, with a quick check for each cause and the symptoms that mean it's time to call a service tech.
Save to PinterestWe may earn a commission when you buy through links on this page. It never changes what we recommend. Learn more
The short answer
Planer snipe is a shallow dip in the first or last few inches of a board, often only a few thousandths to a few hundredths of an inch deep. The most common cause is a board end tipping as it enters or leaves the rollers. Support long boards level at both ends, take lighter final passes, then check table height and roller condition.
- Typical cost
- $0 to $50 for most fixes; $100 to $400 or more for professional roller or table repair
- Time needed
- 30 minutes to one afternoon
- Skill level
- Intermediate
Key points
- Unsupported board ends are the usual cause, so test with level supports on both ends before you adjust anything.
- A straightedge and a feeler gauge will show whether the infeed and outfeed tables sit level with the bed.
- Heavy final passes make snipe worse, so finish with light cuts of about 1/64 to 1/32 inch.
- Dirty or worn bed rollers and a slipping feed chain are the next suspects once support and tables check out.
- If snipe survives every adjustment, or shows up on one side only, stop adjusting and book a service tech.
In this guide
- What does planer snipe look like, and how do I confirm it?
- Cause 1: Is my board supported unevenly at the infeed and outfeed?
- Cause 2: Are the infeed and outfeed tables out of level with the bed?
- Cause 3: Could feed pressure or cut depth be the problem?
- Cause 4: Can worn or dirty bed rollers and a slipping chain cause snipe?
- How do I set table height with a straightedge and dial indicator?
- When does snipe mean I need a professional repair?
Snipe is usually a support problem before it is a machine problem, so run the cheapest test first. Feed a straight, flat 3-foot board while a helper or a pair of roller stands holds both ends level with the bed. If the dip shrinks or disappears, you've found your cause and can skip the wrenches.
What does planer snipe look like, and how do I confirm it?
Planer snipe is a shallow dip in the first or last few inches of a board, often only a few thousandths of an inch deep. A fingertip may barely notice it, but it shows up as a gap under a straightedge and as a ridge once a finish goes on.
To measure it, lay a steel straightedge along the planed face and slide a feeler gauge under the end. Check both ends, because which end dips offers a clue. Front-end snipe often means the board sagged or tipped before the outfeed roller had hold of it. Back-end snipe often means the tail lifted or dropped as it left the infeed roller. Treat that as a rule of thumb, not a diagnosis.
Rule out the board itself. A bowed, twisted, or wet board rides unevenly through a thickness planer and can mimic snipe. The USDA Forest Products Laboratory publishes wood and moisture references if you suspect the stock is the problem. Then work through the causes in this order.
| Check order | Likely cause | Quick check | Typical fix |
|---|---|---|---|
| 1 | Board ends unsupported | Single-board test with level supports | Roller stands, longer stock, lighter passes |
| 2 | Tables out of level with bed | Straightedge and feeler gauge | Adjust or shim the tables |
| 3 | Heavy cuts, feed pressure | Compare a 1/16 inch pass to a 1/64 inch pass | Shallower cuts, carriage lock, pressure settings per manual |
| 4 | Worn or dirty rollers, chain slip | Inspect rollers, clean bed, watch for feed stalls | Clean, wax, replace parts |
Cause 1: Is my board supported unevenly at the infeed and outfeed?
Uneven support is the most common cause of snipe, because a board end that sags or tips as it enters or leaves the rollers gets cut deeper there.
The single-board test settles it. Plane one straight 3-foot board with both ends held at bed height. Keep your hands clear of the infeed opening, and have any helper stand out of the line of the board. Then plane a second board with nothing holding the ends. Compare the two under the straightedge. If only the unsupported board dips, that's your answer.
For most home shops, we'd buy a pair of adjustable roller stands before touching the machine. Set them to bed height at both ends and hold the board level, neither pressing down nor lifting. For short stock, feed boards end to end so each one pushes the next, with a sacrificial board leading and trailing the run. Or cut your stock 2 to 3 inches long and trim the snipe off.
Cause 2: Are the infeed and outfeed tables out of level with the bed?
Yes, tables that sit even slightly above or below the bed can tip a board into or out of the cut, and they're the next thing to check after support.
Unplug the planer first. Lay a straightedge across the bed and onto the outfeed table, then slide a feeler gauge under it at the joint. Repeat on the infeed side and across the width, since a table can be level at one edge and low at the other. Many manufacturers call for tables flush with the bed or a few thousandths of an inch above it. Your manual's number beats our rule of thumb.
Many benchtop models have fixed or folding tables with little adjustment, often just set screws or shim points. Stationary planers usually have adjustable tables and bed rollers.
Cause 3: Could feed pressure or cut depth be the problem?
Yes, a deep final cut and uneven pressure-bar or chipbreaker settings can both exaggerate snipe, and the cut-depth test is easy.
Plane the same board at a 1/16 inch cut, then again at 1/64 inch. If the dip scales with depth, take final passes of about 1/64 to 1/32 inch and save the heavy removal for earlier passes. If your planer has a carriage lock, engage it for each pass to keep the cutter assembly from shifting as the board enters. Release it before you change the height.
Pressure bars and chipbreakers are set to clearances in the manual. A bent or mis-set part can press one end harder than the other. Don't guess. If the numbers are off, adjust to spec or send it out.
Cause 4: Can worn or dirty bed rollers and a slipping chain cause snipe?
Yes. Pitch buildup, glazed rubber, and a stretched chain can let a board shift or stall just as it passes under the cutter.
With the unit unplugged, clean the bed and bed rollers with mineral spirits or a pitch remover, then apply paste wax to the bed. Spin each roller by hand. They should turn freely and sit at the height your manual specifies. Look for flat spots, cracked or hardened rubber, and uneven wear.
Chain slip shows up as a board that hesitates or stops mid-pass. Check chain tension and look for worn sprocket teeth. Adjust tension per the manual, but a chain stretched past its adjustment range needs replacing.
How do I set table height with a straightedge and dial indicator?
Measure each table against the bed with a straightedge for a quick check, or a dial indicator for accuracy, then adjust until the readings match your manual.
- Unplug the planer and clear chips from the bed and tables.
- Place a straightedge across the bed and one table and measure any gap with a feeler gauge.
- For finer readings, mount a dial indicator on a magnetic base, zero it on the bed, and read the table height at the left, center, and right.
- Loosen the table locks and turn the adjustment bolts or screws, or add shim stock where the design calls for it, until readings are flush or slightly high per the manual.
- Retighten, recheck, then plane the test board again.
When does snipe mean I need a professional repair?
Stop adjusting and call a service tech when snipe survives support, table, cut-depth, and roller fixes, or when readings can't be brought into spec.
- Snipe appears on one side of the board only, which can point to a cutterhead that isn't parallel to the bed.
- A table won't reach flat within its adjustment range, or the casting looks bent or cracked.
- Rollers have flat spots, crumbling rubber, or won't hold a consistent height.
- The chain keeps slipping after tension is set, or sprocket teeth are worn.
- Snipe changes unpredictably from board to board with the same setup.
Shop repair typically runs about $100 to $400 or more, depending on the model, parts, and shipping. On an inexpensive benchtop planer, compare the quote to the price of a new machine before you commit. It's also worth checking the CPSC site for recalls on your model.
Tonight, plane one straight test board with both ends supported, measure the dip with a feeler gauge, and write down the number. That's your baseline for every change above.
Questions people ask
Why does a new planer still snipe?
New planers can leave the factory with tables slightly out of level, and long boards still need support no matter how new the machine is. Run the single-board test with level supports first, then check the tables with a straightedge and feeler gauge.
Can I eliminate planer snipe completely?
Often you can reduce it to a few thousandths of an inch, but not always to zero. Cutting stock 2 to 3 inches long and trimming the ends removes whatever is left, which is why extra length is a common habit in woodworking shops.
Does a helical cutterhead reduce snipe?
Not by itself. A helical cutterhead gives a smoother cut and less tearout, but snipe comes from support, table height, and roller behavior. Fix those first, or the dip will show up with either head.
What can I do if my benchtop planer has fixed tables?
Lean on support and technique: roller stands at bed height, light final passes, a sacrificial board at each end of the run, and extra board length to trim off. Check your manual for shim points or adjustment screws before assuming nothing can be changed.
Does board length affect snipe?
Longer boards sag at the ends if nobody supports them, so snipe tends to grow with length. Very short boards can tip as they leave the rollers. Feeding short pieces end to end helps.
Sources and further reading
- OSHA Workplace noise and machine safety guidance for shop use
- U.S. Consumer Product Safety Commission Recall and safety information for power tools
- USDA Forest Products Laboratory Wood and moisture references from the Forest Products Laboratory
Was this article helpful?