Fix and Furrow
Advertise

How to Thaw a Frozen Pipe Safely Without an Open Flame

The order matters: faucet open, supply off, then gentle heat from the tap end back toward the ice.

Save to Pinterest

We may earn a commission when you buy through links on this page. It never changes what we recommend. Learn more

Icicles dripping from a rusty metal pipe with a clamp outdoors
Photo: Liana S on Unsplash

The short answer

Open the faucet served by the frozen pipe, shut off the water supply, then warm the pipe with a hair dryer on low, a heating pad, or warm towels, working from the faucet toward the frozen spot. Expect 30 minutes to two hours. Never use a torch or open flame, and call a plumber if you see a crack or can't reach the freeze.

Typical cost
$0 to $60 in supplies if you own a hair dryer; a plumber thaw visit typically runs $150 to $500 or more
Time needed
30 minutes to 2 hours
Skill level
Beginner

Key points

  • Open the affected faucet and close the main shutoff before you apply any heat, so a hidden crack can't flood the house.
  • Start heating at the faucet end and work toward the blockage so meltwater and steam have somewhere to go.
  • A hair dryer on low, a heating pad, or warm towels will handle most exposed frozen supply lines without risking framing or PEX.
  • Never use a torch, heat gun, or boiling water, and never run electric current through a pipe.
  • Stop and call a licensed plumber for any bulge, crack, wet wall, or a freeze you can't reach or thaw within about two hours.
In this guide
  1. What Do You Need to Thaw a Pipe Without a Flame?
  2. How Do You Confirm a Pipe Is Frozen Before Heating It?
  3. How Do You Find the Frozen Section of a Pipe?
  4. Why Open the Faucet and Shut Off the Supply First?
  5. Which Heat Source Is Safest for a Frozen Pipe?
  6. How Do You Apply Heat From the Faucet End Toward the Blockage?
  7. What Should You Never Use to Thaw a Frozen Pipe?
  8. When Should You Stop and Call a Plumber?

This is general information, not financial, insurance or legal advice. Rates, rules and programs vary by state and change often, so confirm details with the provider or a licensed professional.

Open the cold tap on the affected fixture, shut off the water supply, and warm the pipe slowly with a hair dryer on low or a heating pad. That works on most exposed frozen supply lines in cabinets, crawlspaces, and exterior walls. The details below keep you from cracking a pipe that survived the freeze or scorching the framing around it.

What Do You Need to Thaw a Pipe Without a Flame?

You need a controllable source of gentle heat, a few towels, a bucket, and a way to stop the water if the pipe turns out to be split.

  • Hair dryer with a low setting, plus a short, heavy-duty extension cord plugged into a GFCI-protected outlet
  • Electric heating pad, or thick towels and a kettle
  • Portable space heater with a tip-over shutoff, for pipes inside walls
  • Infrared thermometer (inexpensive, optional) for tracing the cold spot
  • Flashlight, bucket, and rags
  • Wrench or key for the main shutoff valve
  • Work gloves and safety glasses
  • Pipe insulation sleeves, for the last step

How Do You Confirm a Pipe Is Frozen Before Heating It?

A pipe is frozen when one fixture gives you no water or a thin trickle while the rest of the house runs normally, and you can find a cold or frosted stretch of line upstream.

Turn on both hot and cold at the dead fixture. If only the cold side is dry, the freeze is on the cold line. If every faucet in the house is dry, the problem may be the service line, the meter, or the water utility itself, so check with neighbors or your provider before you start pulling cabinets apart. A frozen line between the meter and the street also raises the question of who owns the pipe, and our guide on who is responsible for the water service line from main to house explains how that usually splits.

Then look for damage. A bulge, a split seam, beads of water on the pipe, a hissing sound, or a damp stain on a wall or ceiling all mean the ice has already done its work.

How Do You Find the Frozen Section of a Pipe?

Trace the supply line backward from the dead faucet toward where it enters the house, and look for the stretch that is frosted, noticeably colder, or running along an exterior wall.

Freezes cluster in predictable places: under sinks on exterior walls, near the rim joist where the line comes through the foundation, along crawlspace walls, in unheated garages, and wherever a gap lets outside air hit the pipe. Open the cabinet doors under the sink, aim a flashlight along the back wall, and bump the thermostat up a few degrees so warm air can reach the pipe.

An infrared thermometer makes the search quick. Scan along the run and the frozen section will read near or below 32 degrees Fahrenheit while the pipe on either side reads warmer. Without one, run your bare hand along exposed pipe and feel for the cold stretch. Expect more than one frozen spot. A pipe that froze in one place often froze in two.

If the line runs inside a finished wall and you can't see or touch it, you can warm the wall surface with a space heater from a safe distance, as covered below. If that doesn't work, this is a plumber's job.

Why Open the Faucet and Shut Off the Supply First?

Open the faucet on the frozen line first, then close the main shutoff valve, so meltwater has a place to go and a hidden crack can't flood the house when the ice lets go.

The open faucet relieves pressure that builds between the ice and the tap, and it shows you the moment water starts moving again. On a single-handle faucet, set the handle to the middle so both hot and cold lines can flow. Leave it open for the whole job.

The shutoff matters because a pipe can be cracked without showing it. Ice plugs the leak while it's frozen, then pressure returns as it melts. If the house shutoff won't turn or won't hold, see our walkthrough on how to turn off water at the curb stop when the house shutoff fails.

Which Heat Source Is Safest for a Frozen Pipe?

For an exposed pipe, a hair dryer on low or medium is the safest and most controllable choice, and a heating pad or warm towels are close behind.

The options differ mostly in how much heat they put out and how easily they can go wrong:

Heat sourceBest forWatch for
Hair dryer (low to medium)Exposed copper, PEX, or CPVC in cabinets and crawlspacesKeep it moving, and keep the cord and your hands away from standing water
Electric heating padTight spots and pipes you can wrapDon't fold it onto itself or leave it unattended
Warm towelsShort runs, PEX, and plastic fittingsUse hot tap or kettle water, not boiling, and swap them every few minutes
Heat tapePipes you plan to keep protected afterwardMany types are made to prevent freezing, not thaw, so follow the label for your pipe material and don't overlap the cable unless the product allows it
Space heaterPipes inside walls, warmed from the room sideKeep it at least 3 feet from anything combustible and never leave it running unattended

We'd pick the hair dryer for most homes. It costs nothing if you already own one, you can aim it precisely, and it rarely gets hot enough to hurt anything if you keep it moving. Think of heat tape as prevention, something to install once the line is running again.

How Do You Apply Heat From the Faucet End Toward the Blockage?

Start heating at the faucet end of the frozen run and work back toward the blockage, so melted water and steam can escape through the open tap instead of building pressure behind the ice.

  1. Protect what's behind the pipe. Slide a metal baking sheet or foil-faced board between the pipe and any wood framing or insulation.
  2. Begin nearest the open faucet. Run the hair dryer on low or medium about 3 to 6 inches from the pipe, sweeping over 6 to 12 inches of pipe at a time. Don't park it on one spot.
  3. Move toward the ice as water appears. A trickle means you've opened a channel. Keep heating, shifting a few inches at a time toward the frozen section, until the faucet runs at full flow.
  4. Check every frozen stretch. If water slows or stops, there's another plug further along. Repeat from the faucet end.
  5. Restore the water slowly. With the faucet still open, turn the main shutoff valve back on gradually and watch the pipe with a flashlight for 15 minutes. Look at joints, bends, and the spot that was frozen. Check again an hour later.
  6. Protect the pipe from a repeat. Fit pipe insulation sleeves, seal air gaps around the entry point, leave cabinet doors open on cold nights, and let a thin stream run at the faucet until the weather warms.

Plan on 30 minutes to two hours. If nothing is moving after about two hours of steady, gentle heat, stop and call someone. More heat won't help, and pushing it is how pipes and framing get damaged. For a longer-term plan, see our month-by-month checklist to winterize your water service line.

What Should You Never Use to Thaw a Frozen Pipe?

Never use a propane torch, blowtorch, lighter, kerosene heater, or any other open flame, because pipes sit against wood framing, insulation, and dust that ignite far faster than you'd expect.

Heat guns and paint strippers are nearly as bad. They run hot enough to melt PEX and PVC and to scorch framing before you notice. Boiling water poured straight on the pipe can crack both metal and plastic through sudden temperature change.

Skip the old trick of running current from a welder or battery charger through the pipe. It's a shock and fire hazard and can damage the plumbing and wiring in your house.

Don't leave a space heater running unattended in a crawlspace or cabinet, either. And plug any electrical tool into a GFCI outlet and keep the cord out of every puddle.

When Should You Stop and Call a Plumber?

Stop and call a licensed plumber the moment you see a crack, bulge, or wet wall, or if you can't reach the frozen section or get water moving within about two hours.

Other clear stop signs:

  • Water stains, sagging drywall, or a hissing sound anywhere near the frozen run
  • Pipes buried in a concrete slab, or behind finished walls or ceilings you'd have to open
  • Several fixtures or the whole house dry, pointing to the service line or meter
  • A main shutoff valve that won't close fully
  • Old galvanized or brittle pipe that looks corroded

A thaw visit typically runs $150 to $500, with emergency and after-hours rates pushing it higher depending on your area. Repairing a split pipe costs more, and the water damage can cost far more than the pipe.

If water has already escaped, shut off the main, photograph everything, and dry what you can. Coverage for burst-pipe damage depends on your policy, state, and insurer, and some policies expect you to have kept the house reasonably heated. Call your insurance company before major repairs and ask what documentation it requires. The National Association of Insurance Commissioners publishes consumer resources on how claims work, and our explainer on replacement cost vs actual cash value homeowners insurance covers how payout terms change what you receive.

Once the water is running, insulate the pipe that froze before the next cold night.

Questions people ask

Will a frozen pipe always burst?

No. A pipe usually splits only when ice builds enough pressure between a blockage and a closed tap, and flexible PEX often survives a freeze that would crack copper. The danger is that a split may not leak until the ice melts, which is why you shut off the supply before you thaw.

Can I thaw a frozen pipe inside a wall?

Sometimes. Raise the room temperature and aim a space heater at the wall from a safe distance, but don't leave it unattended. If water hasn't returned in a couple of hours or you see damp spots, call a plumber rather than cutting into the wall yourself.

Is it okay to pour hot water on a frozen pipe?

Hot tap water on towels wrapped around the pipe is fine. Pouring boiling water directly on it risks cracking the pipe from the sudden temperature change, and it makes a mess near outlets and framing.

Should I leave the faucet dripping after the pipe thaws?

Yes, on cold nights. A thin, steady stream keeps water moving and relieves pressure if ice starts to form again. It's a short-term measure until you've insulated the pipe and sealed the air leak.

At what temperature do pipes freeze?

Water freezes at 32 degrees Fahrenheit, but pipes usually need sustained cold to freeze solid. Exposed lines in unheated spaces, along exterior walls, or near drafts are the most vulnerable, so wind and air gaps matter as much as the thermometer reading.

Sources and further reading

Elsewhere in Home Money