Part of our Home Repair Troubleshooting guide
Outdoor Christmas Lights Half Out: Find the Dead Section
The spot where the lights stop points to the part that failed, and a few cheap checks usually find it.
Save to PinterestWe may earn a commission when you buy through links on this page. It never changes what we recommend. Learn more
The short answer
When outdoor Christmas lights go half dark, note where the last lit bulb sits. Then work in order: confirm the outlet and GFCI have power, check the plug fuses, reseat or swap bulbs at the first dark one, and inspect the wire and connectors. A fuse that keeps blowing means a short, so replace the string.
- Typical cost
- $0 to $25 for fuses, a bulb tester, or a replacement string
- Time needed
- 15 to 45 minutes
- Skill level
- Beginner
Key points
- The point where the lit bulbs stop is the best clue you have, so note it before touching anything.
- Check the outlet and GFCI first, then the plug fuses, then bulbs, then wires and connectors.
- Replace a blown plug fuse only with one of the same amperage printed on the plug or tag.
- A fuse that blows again right away, or a GFCI that trips instantly, points to a short, and the string should be retired.
- Scorch marks, melted plastic, or a hot outlet mean stop and call a licensed electrician.
In this guide
- Why is half my string of Christmas lights out?
- Should I check the outlet and GFCI first?
- How do I check and replace the fuse in the plug?
- How do I find a bad bulb in a Christmas light string?
- How do I find a damaged connector or extension cord?
- What if a short takes out everything after it?
- When should I stop and call an electrician?
A string that goes dark partway along usually has its problem at the spot where the lights stop, not at the plug. Find the last lit bulb and you've narrowed the search to a few inches of wire. Unplug the string before you touch any bulb, fuse, or connector.
Why is half my string of Christmas lights out?
Many mini light strings are wired in series sections, so one open spot, such as a dead bulb, loose socket, or broken wire, darkens everything after it in that section. Where the dark stretch begins tells you what to check first.
| What you see | Most likely cause | Check first |
|---|---|---|
| Whole string dead | Dead outlet, tripped GFCI, or blown plug fuse | Outlet, then plug fuses |
| One section dark, rest lit | Loose, missing, or dead bulb in that section | First dark bulb |
| Lit, then dark from one point on | Broken socket, cracked wire, or failed bulb at that point | Bulb and wire at the transition |
| Everything after one string is dark | Bad connector, extension cord, or overloaded run | Connection between strings |
| Fuse or GFCI trips right away | Short, often from moisture or damaged insulation | Isolate each string |
If two strings are chained and the second is dark, test the second alone in a working outlet. That one step shows whether the fault is in the string or in the connection feeding it.
Should I check the outlet and GFCI first?
Yes, check the outlet and GFCI first, because a dead or tripped outlet is the cheapest thing to rule out and takes about a minute. Plug in a lamp or phone charger, press reset on the GFCI outlet, and see whether it has power.
If the GFCI trips the moment the lights go in, or trips later when it rains, suspect moisture. Plug-and-socket connections lying on wet ground or sitting in a gutter are the usual culprits, so lift them off and keep them out of standing water. To find which string is tripping the outlet, unplug everything and add the strings back one at a time.
Read the tag near the plug for how many strings you may connect end to end. Limits differ between incandescent and LED sets, and exceeding them can blow fuses. The Electrical Safety Foundation International publishes holiday lighting safety guidance, and the basics include using only products rated for outdoor use outside.
How do I check and replace the fuse in the plug?
Unplug the string, slide open the fuse door on the plug, and swap any blown fuse for one with the same amperage printed on the plug or tag. Many mini light string plugs hold two small fuses under a sliding door on top, and the swap takes a couple of minutes. A blown fuse usually kills the whole string rather than half of it, but it's still worth a look.
- Unplug the string.
- Slide the door open with a fingernail or the tip of a small screwdriver.
- Pull out both fuses and hold them to the light. A broken wire inside or a dark smudge on the glass means it's blown.
- Install replacement fuses with the same amperage printed on the plug or tag.
- Close the door fully and plug in.
Replacement fuses often come in a small bag with the string, and hardware stores sell packs for a few dollars. If a fresh fuse pops right away, skip to the section on shorts below.
How do I find a bad bulb in a Christmas light string?
Start at the first dark bulb, because the fault is usually that bulb, the one just before it, or its socket. Push every bulb in the dark section firmly into its socket, since a loose or missing bulb breaks the circuit.
In an incandescent string, many bulbs contain a shunt that keeps the rest of the section lit when one filament burns out. Shunts don't always work, and a failed one leaves the whole section dark. A handheld bulb tester, which typically costs $5 to $15, finds the culprit faster than guessing. Without one, unplug the string and swap in a known good bulb of the same voltage, starting with the first dark one. Unplug again before each swap. The section lights when you hit the bad one.
LED strings fail differently. LED bulbs generally outlast incandescent ones, so a partly dark LED string more often points to moisture in a socket, a cracked housing, or a broken wire. Many LED strings use sealed bulbs you can't replace. If yours do snap out, match the voltage and type exactly, and never mix incandescent and LED bulbs in one string. Our outdoor Christmas lights buying guide covers the specs worth matching.
How do I find a damaged connector or extension cord?
With the string unplugged, inspect the wire from the last lit bulb into the dark section, then the connectors between strings and any extension cord feeding the run. Look for cracked insulation, pinched spots, or chewed wire. Pay extra attention wherever the wire passes through a gutter clip, a door frame, or a staple.
To rule out the extension cord, plug the string straight into a working outlet, or try a different outdoor-rated extension cord. If the string lights up, the first cord was the problem.
Don't tape over cracked insulation on a string that lives outdoors. Tape doesn't make a wet-location repair, and a splice in thin light wire is a common spot for failure. If the damage is in the middle of the wire, retire the string. A replacement mini string typically runs $8 to $25 depending on length and type.
What if a short takes out everything after it?
If a short is darkening everything after it, you need to find the shorted string and replace it, not keep re-fusing it. A short happens when the hot and neutral wires touch or water bridges them, and it blows the plug fuse or trips the GFCI. The signs are a new fuse that blows instantly, an outlet that trips the moment you plug in, or a plug that feels warm.
To find the offender, unplug all the strings, then plug each one separately into a GFCI-protected outlet. The one that trips it or blows a fuse is the shorted string. Retire it.
Once a string has been wet and shorted, assume the insulation inside the sockets is compromised. Come spring, store working strings on a spool or a piece of cardboard, as laid out in our outdoor decor winter storage checklist.
When should I stop and call an electrician?
Call a licensed electrician if you see scorch marks, melted plastic, or smell burning at a plug, outlet, or cord, or if the GFCI trips with nothing plugged into it. A breaker that keeps tripping, an outlet that feels hot or sits loose in the wall, or an outlet that stays dead after a GFCI reset all point to the house wiring, not the lights.
The U.S. Consumer Product Safety Commission and the National Fire Protection Association both publish holiday lighting safety tips, and the common thread is simple: don't keep using damaged cords or overloaded outlets. Adding new outdoor outlets or circuits for a permanent setup is electrician work, and permit rules vary by town, so read our permanent outdoor Christmas lighting permit guide first.
Next step: test the string alone at a working outlet tonight, and mark the plug with tape so you know which string is the problem before you hang a single light.
Questions people ask
Why do my new LED Christmas lights keep going out in sections?
Moisture in a socket, a loose bulb, or too many strings connected end to end are common reasons. Check the tag for the maximum number of connected strings, keep connections off wet ground, and test each section alone.
Can I mix LED and incandescent strings on one extension cord?
You can plug them into the same cord as long as the total load stays within the cord's rating, but don't connect them end to end. Each string type has its own connection limit on the tag.
Is it safe to repair a cut Christmas light wire?
Not outdoors. Taped or twisted splices in thin light wire tend to fail in wet weather and can short. Replace the string instead.
Why does the fuse in my light plug keep blowing?
A fuse that blows again right away means a short in the string, often from water in a socket or damaged insulation. Using a bigger fuse removes the protection, so retire the string.
Can I leave outdoor Christmas lights on overnight?
Fire safety groups generally advise turning decorative lights off when you leave home or go to bed. An outdoor-rated timer makes that automatic, as long as the lights stay within its load rating.
Sources and further reading
- Electrical Safety Foundation International Holiday lighting and outdoor electrical safety guidance
- U.S. Consumer Product Safety Commission Consumer product safety tips and recall information
- National Fire Protection Association Fire safety guidance for holiday decorations
Was this article helpful?