Fix and Furrow
Advertise

Part of our Home Repair Troubleshooting guide

Deadbolt Key Turns but Bolt Won't Move: Causes and Fixes

A key that spins freely points inside the lock, but a shifted door can fake the same symptom. Here's how to tell which one you have.

Save to Pinterest

We may earn a commission when you buy through links on this page. It never changes what we recommend. Learn more

Close-up of a brass deadbolt and key on a wooden front door
Photo: Jaye Haych on Unsplash

The short answer

Open the door and work the lock. If the key turns but the bolt still won't move, a worn or broken tailpiece or cam inside the lock is a common cause, and a replacement deadbolt, typically $25 to $100, usually fixes it. If the bolt moves fine with the door open, a sagging door or misaligned strike plate is binding it.

Typical cost
$0 to $15 for lubricant or screws; $25 to $100 for a replacement deadbolt; $100 to $250 for a locksmith visit
Time needed
15 minutes to 2 hours
Skill level
Beginner

Key points

  • Test the lock with the door open first, because that one step separates a lock failure from a door alignment problem.
  • A worn, bent, or snapped tailpiece or cam is a common reason a key spins freely on a lock that worked for years.
  • A sagging door, a misaligned strike plate, or stiff grease can bind the bolt only when the door is closed.
  • Most failed budget deadbolts cost less to replace than to repair, typically $25 to $100 for the hardware.
  • If the bolt is thrown and won't retract, stop and call a locksmith instead of forcing it.
In this guide
  1. How Do You Tell a Lock Failure From a Door Problem?
  2. Why Does the Key Spin Freely? Usually a Worn Tailpiece or Cam
  3. Could a Sagging Door Be Binding the Bolt?
  4. What If the Strike Plate Is Out of Line?
  5. Can Old Grease or Cold Weather Make a Deadbolt Stick?
  6. How Do You Know the Cylinder Itself Has Failed?
  7. Which Fix Matches Which Symptom?
  8. When Should You Call a Locksmith?

Open the door wide and work the lock from the inside. If the bolt slides cleanly in open air, the lock is probably fine and the door is binding it. If the bolt stays put while the key or thumbturn spins, the fault is inside the lock. That one test keeps you from taking apart hardware that works.

How Do You Tell a Lock Failure From a Door Problem?

Operate the deadbolt with the door open: a bolt that moves freely means the lock works and something about the closed door is binding it.

  1. Stand inside with the door open and turn the thumbturn. Watch the bolt on the door edge.
  2. Try the key from the outside, door still open. Note whether the bolt moves fully, partway, or not at all.
  3. If the bolt won't move with the door open, unscrew the two long screws holding the interior half of the lock and pull it off. Turn the key and watch the metal bar that passes through the bolt mechanism.

Why Does the Key Spin Freely? Usually a Worn Tailpiece or Cam

A key that spins freely on a lock that worked for years often means a worn, bent, or snapped deadbolt tailpiece, the flat bar that carries rotation from the cylinder to the bolt.

With the interior half removed, turn the key and watch the tailpiece. If it rotates and the bolt doesn't move, the bolt mechanism is jammed or the bar has rounded off where it grips the cam. If the key turns and the tailpiece stays still, the link between cylinder and tailpiece has failed. Look for a bent bar, a chewed-up slot, or a cam worn smooth on its edges.

Some locks let you buy a replacement tailpiece for a few dollars. Most budget deadbolts don't, and hunting for the part costs more time than the lock is worth. We'd replace the whole deadbolt, which typically runs $25 to $100 depending on grade and finish. A standard 2-1/8 inch bore means the new lock usually drops into the existing door prep without drilling. If the old lock was bargain-bin, step up to an ANSI/BHMA Grade 1 or Grade 2 model while you're at it.

Could a Sagging Door Be Binding the Bolt?

Yes. A door that has dropped or swollen can pinch the bolt in the strike hole so it won't retract, and on a lock with a weak tailpiece the key may then spin without moving it.

Look for an uneven gap along the top of the door, a latch edge rubbing the jamb, or scuff marks near the strike. Tighten every one of the hinge screws first. If a screw spins without biting, replace the middle screw in the top hinge with a 3-inch screw that reaches the wall stud, which pulls the door back toward square. Wood doors also swell in humid weather, and the fit often relaxes when the season changes.

A badly sagged door or a racked frame is carpentry, not lock repair. The same alignment problems show up on new installs, covered in our guide to deadbolt installation mistakes on an exterior door.

What If the Strike Plate Is Out of Line?

A strike plate that sits even a fraction of an inch off the bolt's path can keep a deadbolt from fully extending or retracting, and a lipstick test shows it in one try.

Rub lipstick, chalk, or dry-erase marker on the bolt tip, close the door, and turn the lock as far as it goes. The mark transfers to the strike and shows where the bolt lands. If it hits the edge of the opening, file the hole slightly larger or move the plate. The bolt hole in the jamb should be at least 1 inch deep for a standard 1-inch throw, with clear space behind it.

Don't just keep filing until it works. A bolt that only reaches halfway into the jamb gives up most of the security you installed it for, so realign the door or the strike instead. On a home built before 1978, treat old paint on the jamb as possibly lead-based and use lead-safe methods before filing or sanding.

Can Old Grease or Cold Weather Make a Deadbolt Stick?

Yes, old grease, grit, or cold can gum up a deadbolt enough that the bolt drags, though that usually feels stiff and heavy rather than spinning free.

With the door open, push the bolt in and out by hand if you can. A gritty or sticky drag means the mechanism needs cleaning. Spray a little electronics-safe contact cleaner into the bolt channel and work the bolt back and forth. Then put dry graphite lubricant or a PTFE-based product in the key slot and on the bolt edge. Skip oily sprays in the cylinder, since they attract dust and can gum things up again within a season.

How Do You Know the Cylinder Itself Has Failed?

A failed cylinder is a less common cause, and it shows up as a key that turns with no resistance or feels gritty while the tailpiece and bolt move freely when worked by hand.

Broken pins, a cracked plug, or a sheared retainer can leave the key turning without driving anything. If the tailpiece stays still when you turn the key and the cam looks fine, suspect the cylinder. Some models offer a replacement cylinder, but once you add rekeying, the total often lands close to the price of a new lock. Our rekey cost guide helps you compare before you decide.

Which Fix Matches Which Symptom?

Match the symptom to the row below: the safe fixes are tightening hinge screws, cleaning and lubricating, and nudging the strike into line, while forcing a stuck bolt is never one of them.

CauseTelltale signFixTypical cost
Tailpiece or cam wornKey spins; bolt stays put with door openReplace deadbolt$25 to $100
Door sagWorks open, binds closedTighten hinge screws, use longer screws$0 to $10
Strike misalignedMark lands on edge of strike holeEnlarge hole or reposition plate$0 to $15
Dirt or coldDrags, worse in winterClean, dry graphite lubricant$5 to $15
Cylinder failureKey turns, nothing drivesReplace cylinder or lock$30 to $120

If you're replacing the lock anyway and want keyless entry, our smart lock buying guide explains what to look for before you spend.

When Should You Call a Locksmith?

Call a locksmith if the bolt is thrown and won't retract, if you can't open the door from inside, or if a key is stuck or snapped in the cylinder.

Don't force the key or pry at the bolt. A broken cylinder or jammed bolt can trap you in or out. A locksmith visit commonly runs $100 to $250 depending on region, with higher rates after hours. Also call if the frame is cracked, the door still rubs after you've tightened the hinges, or the strike hole is splitting the jamb, since those are structural repairs.

Your next step: with the door open, run the test at the top of this guide, then match what you see to the table before you buy a new lock.

Questions people ask

Why does my deadbolt turn but not lock?

The key or thumbturn is usually spinning without driving the bolt, which points to a worn tailpiece or cam inside the lock. If the bolt moves with the door open, the problem is a binding door or a misaligned strike plate instead.

Is it safe to use WD-40 on a stuck deadbolt?

A small amount on the bolt edge can loosen it, but oily sprays in the key slot tend to attract dust and can gum the pins over time. Dry graphite or a PTFE lubricant is the better choice for the cylinder.

What if the bolt is thrown and the key just spins?

Try the interior thumbturn first, since it may still retract the bolt. If it doesn't, don't pry at the door. Call a locksmith, because forcing it can damage the door and frame and add to the bill.

How long does it take to replace a deadbolt?

Many homeowners finish in under an hour with a screwdriver when the new lock fits the existing bore and edge hole. Drilling or chiseling for a mismatched lock takes longer and is where mistakes happen.

Do I need a permit to replace a deadbolt?

Swapping a lock on an existing door generally doesn't need one, but local rules vary. Codes on exit doors can limit certain lock types, so check with your building department if you're unsure.

Sources and further reading

Elsewhere in Home Security