Part of our Home Repair Troubleshooting guide
Greenhouse Freezing at Night With the Heater On: Fixes
A bigger heater is usually the last fix, not the first. Work through these causes in order and spend the least money.
Save to PinterestWe may earn a commission when you buy through links on this page. It never changes what we recommend. Learn more
The short answer
A greenhouse that freezes with the heater running is losing heat faster than it makes it. Check in this order: open vents or doors, a thermostat fooled by sun or drafts, air leaks at seams, an undersized heater for your glazing, then cold ground. Measure the overnight low first; most of these fixes cost well under $100.
- Typical cost
- $20 to $150 for most fixes, more if you replace the heater
- Time needed
- One afternoon, plus one cold night to test
- Skill level
- Beginner
Key points
- Measure the overnight low at plant height with a min/max thermometer before changing anything.
- A cracked vent, a poorly placed thermostat, and seam leaks explain many freezing nights and cost little to fix.
- Size the heater with surface area x temperature rise x U-value, using the coldest night you expect, not the average.
- Glazing type can change the heat you need by up to about half, so double-layer film or twin-wall panels can beat a bigger heater.
- Call a pro for tripping breakers, hot cords, gas odors, yellow flames, or a pilot that won't stay lit.
In this guide
- How do you confirm the greenhouse is really freezing?
- Is a vent or door letting the heat out?
- Is the thermostat in the wrong spot?
- Where is air leaking at the frame joints and film seams?
- Is the heater big enough for your structure?
- Is cold ground pulling heat out overnight?
- When should you call an electrician or propane technician?
Before you buy a bigger heater, spend $15 to $30 on a min/max thermometer and leave it at plant height for one cold night. A cracked vent, a fooled thermostat, or air leaks explain many freezing nights, and those fixes cost little. The sections below run from cheapest and likeliest to most expensive.
How do you confirm the greenhouse is really freezing?
Read a min/max thermometer the next morning and compare the indoor low with the outdoor low and your thermostat setting. Keep the probe out of direct sun and several feet from the heater, or it will mislead you.
An indoor low of 34°F with the thermostat set to 45°F means the heater is losing the fight. An indoor low that matches the outdoor low suggests the heater never ran. Listen on a cold evening to see whether it cycles on. A silent electric unit may be on a tripped GFCI outlet, and a quiet propane unit may be out of fuel. Write down three numbers: outdoor low, indoor low, and whether the heater ran.
Is a vent or door letting the heat out?
Yes, a vent or door left even slightly open is a common cause, because warm air escapes as fast as the heater makes it. Walk the structure at dusk and check every roof vent, side vent, louver, and door latch.
An automatic vent opener can fail to close fully if its arm is out of adjustment. Fan louvers and exhaust shutters often hang open a half inch once the spring weakens. Close them by hand and tape or clip them shut for winter if you don't need ventilation on cold days. Add weatherstripping around the door, usually $10 to $30 for a full set, and fix any door that doesn't pull tight against the frame.
Is the thermostat in the wrong spot?
It can be, because a thermostat in direct sun, near the heater, or in a draft will shut the heater off too early or run it at the wrong times. Move it to plant height, in shade, in open air, a few feet from the heater and away from vents and the door.
Sun-warmed sensors are the sneaky problem. A sensor that reads 60°F at 4 p.m. may stay warm into dusk and delay the heater while the air around your plants cools. Put a second thermometer beside the thermostat and compare readings over a day. If they differ by more than a few degrees, relocate it or shade it with a small white shield that still lets air flow through. Check the setpoint too. Cheap controllers can drift, and a wired probe that has frayed or gotten wet can send false readings.
Where is air leaking at the frame joints and film seams?
Leaks show up where panels meet the frame, around the base board, at door and fan openings, and at any torn or loose film. Wind makes them worse, so they matter most on the nights you need heat.
On a cold, breezy evening, hold a stick of incense or a lit candle near seams and watch the smoke or flame. Mark every spot where it bends. Patch small tears in film with greenhouse repair tape, since ordinary duct tape tends to fail in cold and sunlight. Seal base gaps with foam, outdoor-rated caulk, or soil banked against the baseboard. Re-tension loose film so it stops flapping, because flapping widens gaps. Expect $20 to $60 in supplies for a typical hobby greenhouse.
Is the heater big enough for your structure?
A heater is big enough only if its output covers your exposed surface area times the temperature rise you need times the glazing's U-value. The glazing type changes the answer more than most people expect.
The formula: BTU per hour = exposed surface area (square feet) x temperature rise (°F) x U-value. Temperature rise is the gap between your target indoor temperature and the coldest night you expect, not an average night. Your local Cooperative Extension office can usually help with typical record lows, and the USDA Plant Hardiness Zone Map gives a starting point with average annual minimums. The table assumes 600 square feet of exposed surface and a 40°F rise (40°F inside when it's 0°F outside). U-values are approximate and vary by product.
| Glazing | Approx. U-value | Heater needed (BTU/hr) |
|---|---|---|
| Single glass | 1.1 | About 26,400 |
| Single-layer poly film | 1.2 | About 28,800 |
| Double-layer poly film, inflated | 0.7 | About 16,800 |
| Twin-wall polycarbonate | 0.6 | About 14,400 |
Add a margin, often 10 to 20 percent, for wind exposure and aging seals. Compare the total with the heater's rated output, which can be lower than its fuel input.
If your heater falls well short, we'd upgrade the glazing first. Switching single film to double-layer poly film cuts the requirement by roughly 40 percent for the cost of film and a small inflation fan, and it lowers running costs every night afterward. A propane heater can also underdeliver when the tank is nearly empty or very cold, so check the fuel level.
Is cold ground pulling heat out overnight?
Sometimes. Cold soil and concrete can steal heat, especially along the perimeter where frost reaches under the walls, but it's usually a smaller factor than leaks.
Compare the floor temperature near the walls with the center. To cut the loss, bank soil against the base or set 1 to 2 inches of rigid foam board against the baseboard, buried to a depth that suits your local frost line or covered with a skirt. Call 811 before you dig, even for a shallow trench. Bubble film on the lower walls helps too. Painted water barrels in the sun absorb heat by day and release some at night, though they won't replace a heater. For a few seedlings, a small cold frame inside the greenhouse adds a second layer of protection.
When should you call an electrician or propane technician?
Call a licensed pro for electrical faults, gas odors, or a heater that won't stay lit, because these are safety problems, not comfort problems. Don't troubleshoot them past the basics.
- Electrician: breakers or GFCIs that trip repeatedly, warm or discolored plugs and cords, melted insulation, or a heater that needs a new circuit. A diagnostic visit often runs $100 to $300, and a new dedicated circuit commonly costs $300 to $1,000 or more depending on distance and local code.
- Propane technician: any gas smell, a yellow or lazy flame, a pilot that keeps going out, a frosted regulator, or cracked hoses. Shut off the tank at the valve, move away from the greenhouse, and call.
- Local code: permanent gas lines and new wiring typically need permits and inspections, which vary by jurisdiction.
Tonight, put the min/max thermometer out and close every vent. On the next windy evening, run the incense test, then work down this list in order.
Questions people ask
Why does my greenhouse get colder right before sunrise?
The lowest temperature of the night usually hits just before dawn, after hours of heat loss with no sun input. If your heater keeps up at midnight but fails at 5 a.m., it is probably borderline undersized or losing heat to leaks and cold soil.
Can a greenhouse heater be too big?
Yes. An oversized heater short-cycles, which wastes fuel, wears out the unit, and can cause temperature swings. Size to your coldest expected night with a modest margin rather than buying the biggest unit available.
Does a fan help a greenhouse stay warm?
A small circulation fan can even out temperatures so cold pockets don't form near the floor and walls. It doesn't add heat, but it helps the thermostat read the whole space more accurately.
How cold can a greenhouse get before plants are damaged?
It depends on the plant. Tender crops like tomatoes and basil can suffer chilling damage in the 40s°F, and a frost will kill them, while hardy greens tolerate a light freeze. Ask your local Cooperative Extension office about the crops you grow.
Is an electric or propane heater better for a small greenhouse?
Electric is simpler and produces no combustion gases, but it needs adequate circuits and can cost more to run in very cold climates. Propane puts out a lot of heat from a small unit, but it needs careful ventilation and safe fuel handling.
Sources and further reading
- USDA Plant Hardiness Zone Map Find your zone's average annual minimum winter temperature.
- Cooperative Extension (extension.org) Locate your state Cooperative Extension for local greenhouse and cold-snap guidance.
Was this article helpful?