Part of our Roofing and Exterior guide
Egress Window Cost and Size Requirements for Basements
The wall cut, header, window unit, and well are priced separately, and the unit itself is usually the smallest piece.
Save to PinterestWe may earn a commission when you buy through links on this page. It never changes what we recommend. Learn more
The short answer
An egress window typically costs $3,500 to $8,000 installed when a new opening is cut through a foundation wall, well included. Under the International Residential Code, a basement opening needs at least 5.0 square feet clear (5.7 in some places), 24 inches high, 20 inches wide, and a sill no higher than 44 inches. Your local code decides.
- Typical cost
- $3,500 to $8,000 installed for a new opening with a well; $10,000+ for deep, rocky, or hard-to-reach walls
- Time needed
- One to three days on site, plus permit lead time
- Skill level
- Hire a pro
Key points
- A new egress window with a well typically costs $3,500 to $8,000, and difficult sites can pass $10,000.
- The window unit is often just $400 to $1,500 of that total; cutting the wall and building the well are usually bigger line items.
- A basement opening needs 5.0 square feet of clear area under recent model code (5.7 in some places), plus 24 inches of height and 20 inches of width, so a window can pass one number and fail another.
- Measure the clear opening with the sash fully open, not the frame size printed on the window.
- Wells deeper than 44 inches need a ladder, and every well needs a drainage plan, which is why deep basements cost more.
In this guide
- What is an egress window, and when does code require one?
- What size does an egress window have to be?
- How do you check whether an existing basement window qualifies?
- What drives egress window installation cost?
- What do window wells, ladders, and drainage add?
- How much does an egress window cost, and where does the money go?
- Do you need a permit, and what should you ask contractors?
Plan on $3,500 to $8,000 for a new egress window cut into a basement wall, window well included. The window unit is often one of the smaller pieces. The concrete cutting, the structural header, and the excavated well move quotes around, so price them separately before you start collecting bids.
What is an egress window, and when does code require one?
An egress window is an opening big enough to climb out of during a fire, and the model code requires one in every sleeping room and in basements with habitable space. Most U.S. jurisdictions build their rules on International Residential Code section R310. Finishing a basement or adding a basement bedroom typically triggers the requirement. Whether an existing unfinished basement needs one depends on local rules.
A door to the outside can satisfy the rule instead of a window, and a walkout basement often already does. Your city or county decides which code edition applies and may amend it, so confirm with the building department before you draw anything.
What size does an egress window have to be?
Under recent editions of the model code, a below-grade egress opening needs at least 5.0 square feet of clear area, 24 inches of clear height, 20 inches of clear width, and a sill no more than 44 inches above the finished floor. All of those must be true at once.
| Requirement | Minimum or maximum |
|---|---|
| Net clear opening area, basement | 5.0 square feet (720 square inches) in recent model code |
| Net clear opening area, upper floors and some local codes | 5.7 square feet (820.8 square inches) |
| Clear opening height | 24 inches minimum |
| Clear opening width | 20 inches minimum |
| Sill height above floor | 44 inches maximum |
Older code editions and some local amendments apply 5.7 square feet to basements too. We'd size to 5.7 when it costs little extra, because it passes either way and saves you an argument with the inspector.
Here is how the numbers play out. A casement that opens to 24 inches tall by 30 inches wide gives 720 square inches, exactly 5.0 square feet. Make it 24 by 34 inches and you get about 5.67 square feet, which clears 5.0 but misses 5.7 by a hair. At 24 by 36 inches you get 6.0 square feet, which passes both. And a 24 by 20 inch opening meets the height and width minimums while offering only about 3.3 square feet.
How do you check whether an existing basement window qualifies?
Open the window as far as it goes, measure the clear gap you could actually pass through, multiply height by width in inches, and divide by 144 to get square feet. Then measure from the finished floor to the bottom of that opening.
Skip the frame and the glass dimensions. A double-hung window only opens about half its height, so a tall frame can still yield a short clear opening. A casement swings fully open, but the sash and hinge hardware eat a few inches of width. Many old basement hoppers, sliders, and glass block windows fall well short. If you buy a new unit, get the clear-opening numbers from the manufacturer's egress-rated spec sheet rather than trusting the nominal size.
What drives egress window installation cost?
Four things drive egress window installation cost: cutting the wall, supporting the opening above it, the window unit, and the well outside, with drainage tucked inside the well number.
Wall material matters most. Block is often quicker to open than a poured concrete foundation, which needs a wall saw or core drilling and throws off a lot of dust and debris. Cutting concrete releases silica dust, which OSHA treats as a serious respiratory hazard, so ask how the crew controls it. The new opening also needs a steel lintel or reinforced header, and some jurisdictions want an engineer's letter before they approve it. If a gas line, electrical panel, or dryer vent runs along that wall, tell bidders up front.
Then there is access and soil. Hand-digging through clay, rock, or a tight side yard costs more than running a mini excavator across open lawn. If the house predates 1978, ask whether the contractor is EPA lead-safe certified, because disturbing old painted trim falls under the EPA's Renovation, Repair and Painting rule.
What do window wells, ladders, and drainage add?
The well, a ladder once it passes 44 inches deep, and drainage together typically add roughly $1,100 to $4,000, and the well must meet minimum size rules to count.
The model code calls for at least 9 square feet of floor area, with at least 36 inches of projection from the wall and 36 inches of width. The well can't keep the window from opening fully, so check the sash swing. A well a few inches too narrow defeats the purpose.
Past 44 inches deep, you need a permanently attached ladder or steps. Rungs are typically spaced no more than 18 inches apart, and the ladder has to stand out far enough from the wall to be usable. Any window well cover you add must open from the inside without a key, tool, or special knowledge.
Drainage is the cost people forget. Gravel at the bottom is the minimum. Many wells also tie into the footing drain or a dedicated drain line, and a well that fills with water becomes a leak path into your newly finished room.
How much does an egress window cost, and where does the money go?
A new opening through a foundation wall typically runs $3,500 to $8,000 all in, with difficult sites reaching $10,000 or more. Local labor rates and soil conditions swing this a lot, so treat the table as a way to compare quotes, not a price list.
| Line item | Typical range | What moves it |
|---|---|---|
| Cutting concrete or block, debris removal | $1,000 to $3,000 | Wall thickness, material, access |
| Header or steel lintel and framing | $500 to $1,500 | Opening width, load above, engineer review |
| Egress window unit | $400 to $1,500 | Size, material, glass package |
| Window well, gravel, excavation | $800 to $2,500 | Depth, well material, soil, access |
| Drain connection | $300 to $1,500 | Distance to footing drain or daylight |
| Permit, inspection, engineering | $100 to $700 | Local fees |
| Interior trim and drywall | $300 to $1,000 | Finish level |
No single job hits the top of every row. Most land well below the sum of the maximums.
For the most common situation, a basement bedroom in a poured wall, we'd pick a vinyl or fiberglass casement window over a slider. It opens fully, gives the most clear area for its frame size, and is easier to climb through. The Department of Energy's Energy Saver pages explain window efficiency ratings if you're comparing glass packages.
If the room is a bedroom, you have no choice on egress, and a bedroom without legal egress may not count as one in a listing or appraisal. If you only want a family room, an egress window is optional, though it adds light and a second way out.
Do you need a permit, and what should you ask contractors?
Yes, almost every jurisdiction requires a permit to cut a new opening in a foundation wall, and an inspector usually checks the header and the well. Unpermitted openings can surface during a sale or an insurance claim.
Before you sign, ask these:
- Are the permit and inspection fees included?
- Who designs the header, and is an engineer's letter required locally?
- What is the clear-opening size of the exact window, in writing?
- How deep will the well be, and does the price include a ladder if needed?
- Where does the well drain?
- Does the price cover dust control, haul-away, backfill, and regrading?
- Is interior finishing included, or is it extra?
Next step: measure your wall and the distance from the floor to your planned sill, then call your building department to confirm the code edition and minimum opening area. Get three quotes that use the same line items as the table above.
Questions people ask
Can I install an egress window myself?
Cutting a load-bearing foundation wall, setting a header, and building a drained well is structural work that most inspectors expect a licensed contractor to handle. Some homeowners do the interior finishing and the well gravel themselves to save money. Check what your jurisdiction allows before you pull a permit.
How long does egress window installation take?
Most single-window jobs take one to three days of on-site work. Permit approval, utility marking, and scheduling the inspection often add more calendar time than the work itself.
Does glass block or a fixed window count as egress?
No. An egress opening has to open from the inside without keys or tools, and a fixed pane or glass block can't be climbed through. The window must also meet the clear-opening minimums with the sash fully open.
Can I add a second egress window in the same basement for less?
Often the second opening costs somewhat less than the first, because the crew is already set up and the equipment is on site. The saving isn't guaranteed, so ask for a price on two openings when you request quotes.
Does an egress window need a window well cover?
No, covers are optional. If you add one, it has to open from the inside without a key or tool and must not interfere with using the opening. A cover helps keep out leaves and snow, but make sure it doesn't trap water.
Sources and further reading
- OSHA Workplace guidance on silica dust from cutting concrete
- EPA Lead (Renovation, Repair and Painting) Lead-safe rules for renovation work in pre-1978 homes
- U.S. Dept. of Energy, Energy Saver Window efficiency basics for choosing a replacement unit
Was this article helpful?