How to Store Christmas Lights So They Work Next Year
Test each strand and flag dead sections now, while you still remember where they are, and next December's untangling goes a lot faster.
Save to PinterestWe may earn a commission when you buy through links on this page. It never changes what we recommend. Learn more
The short answer
Plug in each strand before you take it down, flag any dead section with painter's tape, and fix or toss it. Sort strands by length and plug type, wind each one around cardboard or a wide reel, and pack them in a lidded plastic bin. Store the bin somewhere dry that stays roughly between 40°F and 85°F.
- Typical cost
- $10 to $60 for supplies, plus replacements
- Time needed
- 1 to 3 hours, depending on how many strands
- Skill level
- Beginner
Key points
- Test every strand while it's still hung, so you can see exactly which section is dead and fix it before it goes in a box.
- Wind lights around flat cardboard or a wide reel with snug, even tension, never around your hand and elbow or in a loose ball.
- A lidded plastic storage bin beats a cardboard box because it keeps out moisture, crushing and mice.
- Attics and uninsulated garages swing too hot, cold or damp for many cords and sockets, so an interior closet or shelf is the better spot.
- Replace any strand with cracked insulation, exposed wire, a loose socket or a warped plug instead of storing it.
In this guide
- What Do You Need Before You Start?
- Should You Test Every Strand Before Taking It Down?
- How Do You Label and Sort Christmas Lights?
- How Do You Wind Christmas Lights Without Kinks?
- What's the Best Container for Storing Christmas Lights?
- Where Should You Store Christmas Lights: Garage, Attic or Closet?
- What Makes Stored Lights Fail by Next Season?
- When Should You Replace a Strand Instead of Storing It?
Plug in every strand while it's still hanging, and mark any dead section with a strip of painter's tape right on the wire. That two-minute check does more for next year's lights than any fancy box, because it turns a December mystery into a known repair you can handle on a quiet afternoon.
The rest is mechanical: sort, wind gently, pack with something rigid, and keep the box somewhere that doesn't bake or sweat.
What Do You Need Before You Start?
You need painter's tape, cardboard or a reel, soft ties, a lidded bin and silica gel, which usually runs $10 to $60 total, and you probably own some of it already.
- Painter's tape and a marker, for flagging dead sections and labeling strands
- A light bulb tester, or a pack of replacement bulbs and spare plug fuses that match your strands (check the packaging or the strand's tag)
- Cardboard sheets about 6 by 12 inches, or a string light reel sized for your longest strands
- Soft ties, either hook-and-loop ties or paper-coated twist ties
- A plastic storage bin with a snap-on lid, ideally shallow so you're not stacking lights deep
- A few silica gel packs per bin
- A stepladder, work gloves and a helper to steady the ladder
Skip rubber bands, packing tape and wire twist ties with exposed metal. Rubber bands go brittle or sticky in storage, and bare wire can bite into cord insulation.
Should You Test Every Strand Before Taking It Down?
Yes. Test each strand while it's still hung, ideally at dusk, because that's when you can see which section is out and where it sits on your house or tree.
Plug it in and give it a few minutes. Many incandescent mini strings are wired in sections, so one burned-out or loose bulb can darken a whole run. Push each bulb in firmly, swap in replacement bulbs where you find a dark one, or use a light bulb tester to find the culprit. LED sets often fail by section too, usually from a loose connection or moisture in a socket. If a section stays dark after you've reseated the bulbs, check the plug fuses. Most plugs have a small sliding door on top, and the fuses inside are cheap. Replace them only with the same rating printed on the strand.
Then unplug it and look over the whole cord for cracked or chalky insulation, bare copper, wobbly sockets, scorch marks, and a plug that's warped or discolored.
Work from a stepladder on firm, level ground with a helper steadying it, and don't overreach to grab a far clip. OSHA's site has general ladder safety guidance if you want a refresher.
How Do You Label and Sort Christmas Lights?
Mark every dead section with painter's tape right away, then sort the strands by length, plug type and bulb type so you can find what you need next year without testing the whole pile.
Make the tape flag say what you know: "dead after bulb 30," "fuse blown, replaced," or "works, flickers when bent." Write on the tape, not the cord, since marker on insulation smears and can eat into some plastics. Put the tape where it will still be readable once the strand is wound.
Sort into groups before you wind anything:
- Length: keep 25-foot, 50-foot and longer strands in separate piles, or group by bulb count if the packaging lists it.
- Plug type: separate strands with end-to-end connectors from single-plug sets, and flat two-prong plugs from three-prong ones.
- Bulb type: keep incandescent and LED apart. The number of sets you can connect in a row often differs widely between them, and the tag on each strand gives its limit. Follow the tag, and don't mix brands on one run.
This sorting is what saves you next November. You pull one bin, read the length and plug labels, and know in a minute whether you have enough for the porch rail.
How Do You Wind Christmas Lights Without Kinks?
Wind each strand around a flat piece of cardboard or a wide reel with even, snug tension, because balling lights up or looping them around your hand and elbow stresses the wire at every socket.
Here's the method:
- Unplug and wipe it down. Make sure the strand is dry, then wipe off grit with a dry cloth. Damp lights packed away invite corrosion in the sockets.
- Cut a notch. On your cardboard, cut a slot about half an inch deep in each short end. Tuck the plug end into one slot to anchor it.
- Wind lengthwise. Run the wire across the face of the cardboard and let the bulbs sit along the edges, staggered so they don't stack. Bulbs pressed together under tension can crack sockets and snap the thin wire at the base.
- Keep tension snug, not tight. The cord should lie flat. If you're pulling hard enough to stretch it, ease off.
- Leave both plugs reachable. Tuck the far end into the opposite notch so you can test next year before you unwind anything.
- Secure and label. Slip on a loose hook-and-loop tie and stick on a tape label with length, bulb type and any dead-section note.
What's the Best Container for Storing Christmas Lights?
A rigid plastic storage bin with a snap-on lid is the best container for most homes, because it blocks moisture, resists crushing and keeps mice out in a way cardboard doesn't.
Choose a shallow bin, roughly 12 to 20 quarts, over a deep tote, where the bottom layers get squashed by the weight above. Stand the cardboard winds on edge side by side, or lay them flat in two or three layers with a sheet of cardboard between each. Drop in two or three silica gel packs, snap the lid on and label the outside with the strand lengths inside.
Cardboard boxes are fine for the short term, but they soak up damp, collapse under weight and give rodents something to nest in. Chewed insulation is a common spring surprise. Trash bags are worse, since they trap moisture and crush everything.
Keep the lights in their own bin. Mixed with ornaments or tools, they get crushed.
Where Should You Store Christmas Lights: Garage, Attic or Closet?
An interior closet or shelf is the best place to store Christmas lights, and if you don't have one, pick the garage or basement spot with the smallest temperature swings and no dampness.
Cord insulation and plastic sockets get brittle with heat and age, and cold plus condensation corrodes metal contacts. Here's how the usual spots compare:
| Location | Main risk | Verdict |
|---|---|---|
| Interior closet or under-bed | Few. Stable temperature and low humidity. | Best choice |
| Attic | Summer heat that can run well past 100°F in many climates, which can harden and crack cord insulation | Avoid unless it's insulated and conditioned |
| Unheated or uninsulated garage | Temperature swings, condensation and rodents | Acceptable on a wall shelf, in a sealed bin, off the floor |
| Basement | Humidity and occasional flooding | Acceptable on a high shelf with silica gel packs, if the space stays dry |
If your climate runs to extremes, the closet wins even if it costs you a shelf. If the garage is your only option, put the bin on a shelf at chest height, not on the concrete floor and not on a top rack where summer heat collects. Our garage storage winter prep checklist covers the rest of the fall tasks for that space. And if you're thinking of boarding over attic joists to make room, read what to check before building an attic storage floor first, because that can raise permit and load questions.
What Makes Stored Lights Fail by Next Season?
Rough takedown, damp packing and crushing weight are the usual reasons stored lights fail.
Yanking lights off gutters and shrubs stretches wire and snaps sockets, so unclip each clip by hand. Packing strands that are still damp invites corrosion over the winter. A paint can set on top of a bin can flatten bulbs and crack sockets. If a set runs on batteries, take them out, because leaking batteries ruin the compartment.
Skipping the test is the quiet mistake. You pack a dead strand, then troubleshoot it in the cold next November.
When Should You Replace a Strand Instead of Storing It?
Replace a strand if the insulation is cracked, copper shows, a socket is loose or scorched, or the plug is warped, because those are shock and fire hazards, not storage problems.
The same goes for a strand that stays dark after you've reseated the bulbs and swapped the fuses. A basic 100-light strand typically runs roughly $5 to $25, with LED and commercial-grade sets costing more. That's rarely worth an hour of fiddling. Sealed LED strings usually can't be repaired at all, and you shouldn't cut and splice the cord. If you're replacing a lot of old incandescent sets, the Department of Energy's Energy Saver site explains why LED holiday lights draw far less power. Some retailers and local recycling programs take old strands, so check before tossing them in the trash.
Call a licensed electrician if outdoor outlets are dead or keep tripping a GFCI, if lights are wired into permanent fixtures or soffit circuits, or if you find scorched outlets or plugs that were hot to the touch. Don't diagnose wiring yourself.
Your next step: pick one strand tonight, plug it in, and tape-flag whatever's dead. Then do the rest on the weekend while the lights are still on the house.
Questions people ask
Can I store Christmas lights on the tree?
It's better to take them off. Strands left on a pre-lit artificial tree can be crushed or bent when the tree is folded and boxed. If you do leave them on, test them first, cover the tree sections loosely and keep the whole thing somewhere dry.
How long do Christmas lights last?
There's no fixed lifespan. LED strands often last many seasons, while cheap incandescent sets tend to fail sooner. Handling, storage temperature and moisture all matter, and a strand with damaged insulation should be replaced however old it is.
Should I remove batteries from battery-powered lights?
Yes. Batteries left in storage can leak and corrode the contacts in the battery box, which kills the strand. Pull them out, tape the compartment shut and store fresh batteries separately.
Can I use zip ties to hold wound lights?
Use soft ties instead. A tight zip tie can pinch the cord and leave a permanent crimp. If zip ties are all you have, leave them loose and cut them off next year.
What temperature is too cold or too hot to store lights?
Manufacturers don't all publish a number, so check the packaging if you still have it. As a practical guide, aim for a space that stays roughly between 40°F and 85°F. An attic that gets much hotter than that in summer is the usual problem spot.
Sources and further reading
- U.S. Consumer Product Safety Commission Federal holiday lighting and electrical safety guidance from the CPSC
- U.S. Dept. of Energy, Energy Saver Department of Energy overview of LED lighting and energy use
- OSHA General ladder and fall safety resources for working at height
Was this article helpful?