Cost to Rewire Phone Lines in a House: 2026 Price Guide
Per-run and whole-house price ranges for replacing old gray station wire, plus how to test each line before you pay anyone.
Save to PinterestWe may earn a commission when you buy through links on this page. It never changes what we recommend. Learn more
The short answer
Expect about $150 to $450 per run when walls are reasonably accessible, and $800 to $3,500 for a typical whole-house rewire of four to eight runs. Wire is cheap, around $0.15 to $0.50 per foot. Labor and wall access drive the bill, so test every run first and replace only the ones that fail.
- Typical cost
- $150 to $450 per run; $800 to $3,500 for a whole house
- Time needed
- One day for a few runs; a full weekend or more for a whole house
- Skill level
- Intermediate
Key points
- Wire is the smallest cost; labor and getting through plaster and framing set the price.
- Test each run at the network interface device and at the jack before replacing anything, because a bad jack or loose splice is often the real culprit.
- Replace a single failing run on its own, and rewire the whole house only when several runs fail or you want to modernize the system.
- Pulling cat5e cable instead of old 4-conductor station wire costs little extra and keeps your options open.
- Get itemized quotes that separate per-run labor, materials, and wall patching.
In this guide
This is general information, not financial, insurance or legal advice. Rates, rules and programs vary by state and change often, so confirm details with the provider or a licensed professional.
Most of the price of a phone rewire is labor and wall access, not wire. Cable runs roughly $0.15 to $0.50 per foot, so a 60-foot run costs under $30 in material. What you pay for is getting that cable from the basement or attic to a jack in a finished room without wrecking plaster. The prices below are typical U.S. ranges and swing with your region, your house, and the installer, so use them to judge quotes, not to predict one.
What Is Inside Phone Wiring, and When Does It Need Replacing?
Inside phone wiring is the copper run from the network interface device on your exterior wall to each phone jack, and it needs replacing when testing shows the fault is in those runs rather than in the provider's outside line.
Older houses typically have gray or beige 4-conductor station wire, often stapled along joists and fished through plaster-and-lath walls. Only two conductors, red and green, carry a standard single line. The yellow and black pair is a second line that many houses never used. Insulation turns brittle, staples pinch it, and splices from decades ago corrode.
The usual signs are constant static, no dial tone at one jack while the others work, DSL that keeps dropping out, or visible damage from a rodent, a drill bit, or a past renovation. If you need only one working line in one room, a full rewire may not be the smart move. And if your phone service now arrives over cable or fiber, the old copper may not carry dial tone at all, so ask your provider what your jacks are actually connected to.
How Much Does It Cost to Rewire Phone Lines in a House?
A single replaced run typically costs $150 to $450, and a whole-house rewire of four to eight runs usually lands between $800 and $3,500, with labor making up most of that.
| Item | Typical range | Notes |
|---|---|---|
| Cable (cat5e or 4-conductor) | $0.15 to $0.50 per foot | A 1,000-foot box often runs $100 to $200 |
| Jacks, faceplates, old-work brackets | $5 to $20 per location | Basic wall jacks are cheapest; keystone jacks cost more |
| Tools if DIY (tester, fish tape, punch-down tool) | $40 to $150 total | Reusable on later projects |
| Labor, accessible run (basement or attic access) | $100 to $250 per run | Often billed hourly |
| Labor, finished walls, plaster, or two-story drops | $200 to $450 per run | Add more if framing blocks the path |
| Service call or minimum charge | $75 to $250 | Sometimes waived if you hire for the job |
| Wall patching and paint | $100 to $400 per repair area | Plaster costs more than drywall |
| Whole house, 4 to 8 runs, all-in | $800 to $3,500 | Higher end includes repairs |
Hourly rates for a licensed electrician or low-voltage installer commonly run about $65 to $150, depending on your area. Ask for the quote itemized so you can see which part is wire, which is time, and which is wall patching.
What Pushes the Price Up or Down?
The number of runs and how hard each one is to reach matter most, followed by wall construction, house height, and whether you want Ethernet pulled along with the phone line.
- Run count. Each run adds labor. Dropping unused jacks from the plan is the fastest way to cut the total.
- Wall access. A run that follows a basement ceiling into a wall cavity is cheap. Plaster and lath, firestops, and insulated exterior walls slow everything down.
- Floors. A second-floor jack often means drilling through top plates and fire blocking.
- Cable choice. Cat5e cable costs a little more per foot than old station wire but carries phone and data, and its four pairs leave room for a second line later. Two-conductor phone wire can't do that.
- Region and demand. Labor in large metros runs well above rural rates.
- Hidden problems. Knob-and-tube wiring nearby, vermiculite insulation, or crumbling plaster can stop a job or add cost.
For most houses we'd pull cat5e cable to the one or two jacks you really use and skip the rest. It adds little to the bill and saves you from opening the same wall twice.
How Do You Test Your Existing Runs Before Spending Anything?
Start at the network interface device: plug a working corded phone into its test jack, and if you hear dial tone there, the provider's line is fine and your problem is inside the house.
Many providers treat everything on the house side of that box as the homeowner's responsibility, though some sell inside-wire repair plans, so ask yours. The FCC's consumer pages at fcc.gov are a reasonable place to check how responsibility is generally divided. Rules and plans vary by state and provider.
- Disconnect the house wiring inside the network interface device so you test one thing at a time.
- Plug the corded phone into each jack and note which have dial tone, noise, or nothing.
- Open any bad jack and look for loose screws, green corrosion, or a pinched conductor. Swapping a phone jack costs a few dollars.
- Use a line tester to check polarity and pair continuity. A tone generator and probe lets you trace a dead run back toward its source.
- If a run is dead at the jack but the tone shows up at the basement end, the break is somewhere between. That's the run to replace.
Idle phone lines carry low DC voltage, but ringing voltage can give you a noticeable jolt. Keep your fingers off bare conductors, or unplug the line at the network interface device first.
How Can You Cut the Cost Without Cutting Corners?
Replace only the runs that failed testing, skip jacks nobody uses, and compare at least three itemized quotes.
Fix bad jacks and splices first, since they are the cheapest failures to solve. Most homes need one or two working locations now, not six, so consolidate. If a jack can move a few feet to sit on an accessible path, such as a basement ceiling or attic floor, the labor drops noticeably.
Bundle the job if you want Ethernet too. Pulling both cables while the walls are open costs far less than coming back later. Ask each bidder whether the quote includes wall patching and paint, because that line is where quotes quietly diverge. The FTC's consumer advice site has general guidance on hiring contractors and getting terms in writing.
Should You DIY the Rewire or Hire a Pro?
Phone wiring is a reasonable DIY job when your walls are accessible, but hire a pro for plaster, two-story drops, or anything near line-voltage wiring or hazardous materials.
Low-voltage phone and data work often needs no permit, but that varies by city and county, so call your building department before opening walls. Local code also governs fire blocking: holes you drill through it generally need to be sealed with fire-rated material, and that's one more reason to leave multi-floor runs to someone who does them weekly. If you uncover damaged electrical wiring, knob-and-tube, or suspect asbestos, stop and bring in a licensed electrician or abatement contractor.
Next step: run the test above at every jack this week, write down which ones fail, and take that list to your quotes. It will shrink the job, and the price with it.
Questions people ask
Who is responsible for phone wiring inside my house?
In most cases the homeowner is responsible for wiring on the house side of the network interface device, and the provider handles the line outside it. Some providers sell inside-wire maintenance plans, and rules vary by state, so check your service terms.
Can I use cat5e for a regular phone line?
Yes. A standard analog phone line needs only one pair, and cat5e has four. Terminate it at a phone jack or keystone jack and the same cable can carry data on the other pairs or a second line later.
Can I reuse the old yellow and black pair for a second line?
If the pair is intact and tests clean, it can carry a second line, but your provider has to activate that line on its end. Test it for continuity first, since unused pairs in old cable are sometimes damaged or corroded.
Will rewiring fix slow DSL?
It can if noise or a bad splice inside the house is the cause, but it won't raise the speed your plan delivers. Missing filters and a bad jack are common culprits, so have the provider check the line at the network interface device first.
How long does a phone rewire take a professional?
A few accessible runs often take a day or less, while a whole house with finished walls can take one to two days plus patching time. Plaster, multiple floors, and surprises behind the walls are what stretch the schedule.
Sources and further reading
- Federal Communications Commission Consumer help on telephone service and who handles which part of the line
- FTC Consumer Advice General consumer advice on hiring contractors and comparing quotes
Was this article helpful?