Kitchen Countertop Replacement Cost in 2026: What Quotes Skip
Material is only the start. Templating, sink cutouts, edges, backsplash pieces, and demo separate a complete quote from a lowball one.
Save to PinterestWe may earn a commission when you buy through links on this page. It never changes what we recommend. Learn more
The short answer
Expect roughly $1,000 to $6,000 installed for a typical kitchen with about 40 square feet of counter. Laminate runs $25 to $65 per square foot installed, granite $60 to $130, and quartz $75 to $150. Add $150 to $500 for an undermount sink cutout, plus demo, edge, and backsplash charges if the quote leaves them out.
- Typical cost
- $1,000 to $6,000 installed for about 40 square feet
- Time needed
- 1 to 3 weeks from template to install; install day is usually a few hours to a day
- Skill level
- Hire a pro
Key points
- A 40-square-foot kitchen costs about $1,000 to $2,600 in laminate, $2,400 to $5,200 in granite, and $3,000 to $6,000 in quartz, installed.
- Fees outside the material price, such as the sink cutout, edge profile, backsplash, and demo, often add $400 to $1,500.
- To estimate square feet, multiply each run's length by its depth in inches, divide by 144, and count corners only once.
- A low quote usually omits demo, plumbing hookup, or cutouts, so compare itemized bids for the same scope.
- Laminate and butcher block are realistic DIY jobs; quartz, granite, and solid surface belong with a fabricator.
In this guide
- What does kitchen countertop replacement cost overall?
- How much do laminate, solid surface, quartz, granite, and butcher block cost?
- Which labor and fabrication fees aren't in the material price?
- What pushes the price up or down in your kitchen?
- How do you measure counters and estimate square footage?
- How can you save without lowering quality?
- Should you DIY removal and installation or hire a fabricator?
Plan on roughly $1,000 to $6,000 installed for a typical kitchen with about 40 square feet of counter. Premium stone or a big island will push past that. The per-square-foot material price is only the headline. Templating, sink cutouts, edge work, backsplash pieces, and hauling off the old top all add up, and a quote that looks cheap has often just left them off.
What does kitchen countertop replacement cost overall?
Kitchen countertop replacement cost for a 40-square-foot kitchen runs about $1,000 to $2,600 for laminate, $2,400 to $5,200 for granite, and $3,000 to $6,000 for quartz, all installed. Region, layout, and the slab you pick move the final number.
Big-city and coastal markets tend to price higher than rural ones, and a large island or a second run of counter can push a stone kitchen past $8,000. Use these ranges to compare bids. Fabricators set their own rates, and slab prices shift with supply.
How much do laminate, solid surface, quartz, granite, and butcher block cost?
Material alone runs from about $10 per square foot for basic laminate to $100 or more for premium quartz, and installation adds roughly $15 to $50 per square foot on top.
| Material | Material only, per sq ft | Installed, per sq ft | Installed, 40 sq ft kitchen |
|---|---|---|---|
| Laminate | $10 to $35 | $25 to $65 | $1,000 to $2,600 |
| Butcher block | $25 to $70 | $40 to $100 | $1,600 to $4,000 |
| Solid surface | $35 to $75 | $50 to $100 | $2,000 to $4,000 |
| Granite | $35 to $90 | $60 to $130 | $2,400 to $5,200 |
| Quartz | $50 to $100 | $75 to $150 | $3,000 to $6,000 |
A laminate countertop is the budget pick, and post-formed tops with a rounded front edge are the cheapest of all. The tradeoff: laminate chips, scorches, and swells at seams if water sits, and it can't take a true undermount sink.
Butcher block is warm and easy to cut, but it needs regular oil or sealer and it punishes standing water around the sink. Solid surface can be joined with nearly invisible seams, and minor scratches can be sanded out. It does mark under hot pans.
The quartz countertop price moves with brand and color tier. Quartz is engineered and nonporous, so it never needs sealing, though the resin can discolor under very hot cookware. Granite countertop installation cost depends mostly on the slab's color tier. Common colors are moderate, while exotic, heavily veined slabs can top $150 per square foot installed. Natural stone needs periodic sealing.
For most remodels, we'd pick mid-tier quartz. The price is predictable, the pattern is consistent so seams hide well, and there's nothing to seal. If you want natural stone, ask for mid-tier granite from slabs the fabricator already has in stock. It often lands close to quartz pricing.
Which labor and fabrication fees aren't in the material price?
Fees for templating, cutouts, edges, backsplash pieces, and demo often add roughly $400 to $1,500 to a stone or quartz job, and they're where bids differ most.
| Line item | Typical cost | What to know |
|---|---|---|
| Countertop template and fabrication fee | $0 to $300 if listed separately | Many shops bundle it into the per-square-foot price. Ask. |
| Undermount sink cutout | $150 to $500 | Stone and quartz only. Drop-in cutouts often cost $0 to $150. |
| Cooktop cutout | $50 to $200 | Needed for a drop-in cooktop, not a freestanding range. |
| Edge profile upgrade | $5 to $40 per linear foot | Eased and square edges are usually included. Ogee, bullnose, and mitered edges cost more. |
| Backsplash return (4-inch) | Often included, or $5 to $15 per linear foot | Full-height stone backsplash runs about $15 to $50 per square foot. |
| Demo and disposal of old top | $100 to $500 | Higher if the old top is stone or tile set in mortar. |
| Plumbing disconnect and reconnect | $100 to $400 | A plumber, if the fabricator doesn't handle it. |
| Delivery and long-haul fees | $0 to $300 | Rises with distance and stairs. |
How can you tell if a low quote left items out?
A low quote is usually missing something from the table above, so check the line items before you compare totals. Ask each bidder these questions in writing:
- Is the template visit and fabrication included, or billed separately?
- Does the price cover the sink cutout, faucet holes, and any cooktop cutout?
- Which edge profile is priced, and what does an upgrade cost per linear foot?
- Is the backsplash return included, and how tall?
- Does it include demo, disposal, and the plumbing hookup?
- How many square feet are billed: the slab or the finished piece?
The FTC's consumer advice site has general guidance on hiring contractors and avoiding home-improvement scams. Get a signed scope before you pay a deposit.
What pushes the price up or down in your kitchen?
Layout, slab choice, and the condition of your cabinets move the price most. A simple galley with two straight runs is cheap to fabricate. An L-shape adds a seam. An island with a seating overhang may need support brackets and a separate slab piece.
Thicker 3-centimeter stone costs more than 2-centimeter. Strongly veined patterns can require extra slab to match the grain across seams, and you pay for that waste.
Cabinets matter too. Out-of-level bases need shimming, and weak or sagging boxes may need reinforcing before heavy stone goes on. Tight stairs or an upper-floor kitchen can bring a delivery surcharge. If removing the old top damages tile or drywall, budget for repair.
A pre-1978 home adds one more check. Ask any paid contractor about EPA lead-safe work practices before demo touches painted surfaces. The EPA lead page explains the renovation rule.
How do you measure counters and estimate square footage?
Measure each run's length and depth in inches, multiply them, and divide by 144 to get square feet. Standard base cabinets are about 24 inches deep, and the counter overhangs to around 25.5 inches.
- Sketch the layout and split it into rectangles.
- Measure each run along the wall, then its depth, including overhang.
- In an L-shape, count the corner once by shortening the second run by the depth of the first.
- Add island, peninsula, or bar sections as their own rectangles.
- Add all the areas, then add 10 to 15 percent for waste on stone and quartz.
Here's an example. A 120-inch run plus a 96-inch run forming an L: the first is 120 x 25.5 = 3,060 square inches. The second, shortened for the corner, is 70.5 x 25.5 = about 1,798. Together that's roughly 33.7 square feet. A 72 x 36-inch island adds 18 square feet, for about 51.7 total.
Also measure linear feet along each exposed front edge, since edge profiles and backsplash returns are priced that way. Your fabricator will field-measure at the template visit, and slab pricing can bill whole or partial slabs, so use your numbers to compare bids, not to order material.
How can you save without lowering quality?
The biggest savings come from keeping your cabinets, choosing a standard edge, and shopping slabs the fabricator already has in stock. These moves also cut cost without hurting the result:
- Pick an eased or square edge profile instead of a decorative one.
- Use a 4-inch backsplash return and tile the rest yourself instead of running stone up to the wall cabinets.
- Ask about remnants for small kitchens, islands, and bathroom vanities.
- Choose a drop-in sink to skip the undermount sink cutout fee, if you like the look.
- Pull the old top yourself if it's laminate and the plumbing is already disconnected.
- Ask whether your fabricator discounts in a slow season. Some do, many don't.
Don't cut the countertop template visit or the fabricator's seam plan. Skimping there shows up later as cracks and visible joints.
Should you DIY removal and installation or hire a fabricator?
Do it yourself only for laminate or butcher block, and hire a fabricator for quartz, granite, and solid surface. Stone tops weigh roughly 15 to 20 pounds per square foot at 3 centimeters, crack if lifted wrong or poorly supported, and need precise cutouts that are hard to correct once made.
A DIY laminate or butcher block install can save $300 to $1,000 in labor. Allow a weekend and some careful scribing against walls. Removing the old top is the easiest piece to take on, and doing it yourself can trim the demo fee, so ask your fabricator first.
Before the old top comes out, shut off the water, disconnect the supply lines and drain, and kill power to any disposal or appliance wiring. A like-for-like swap often doesn't need a permit, but moving plumbing or outlets usually does, and requirements vary by town. Check with your building department, or start with the International Code Council for the model codes many jurisdictions adopt. Have a licensed electrician move or add outlets, since GFCI rules near sinks are strict.
Your next step: measure your counters with the method above, then ask two or three local fabricators for itemized quotes on the same material, edge, sink, and backsplash.
Questions people ask
How long does a countertop replacement take?
Stone and quartz usually take one to three weeks from the template visit to installation, because the slab has to be cut and polished. Install day itself typically runs a few hours to a day. Laminate can move faster if you buy stock sizes.
Can I put new countertops over the old ones?
Sometimes with laminate, if the old surface is flat and well bonded, though it often leaves an uneven edge and a thicker profile. Stone and quartz need a clean, level cabinet base, so the old top comes off first.
When should I order countertops during a cabinet remodel?
Wait until the cabinets are installed and level, because the fabricator templates from the finished boxes. Ordering from a plan risks gaps and recuts. Pick your sink and cooktop first, since the cutouts depend on their exact dimensions.
Is quartz cheaper than granite?
Not always. Granite in common color tiers can cost less than mid-tier quartz, while exotic granite can cost more than either. Compare actual slabs and an itemized quote from the same shop.
Do I need to replace my sink with new countertops?
Not necessarily, but switching to an undermount style requires stone or quartz and a new cutout. An old drop-in sink may not fit the new opening, so confirm the model with the fabricator before the template visit.
Do countertop replacements need a permit?
A straight swap usually doesn't, but moving plumbing, gas, or outlets often does. Rules vary by city and county, so call your local building department before work starts.
Sources and further reading
- FTC Consumer Advice Consumer advice on hiring contractors and avoiding home-improvement scams
- EPA Lead (Renovation, Repair and Painting) Lead-safe renovation rules for homes built before 1978
- International Code Council Model building code resources for electrical and plumbing requirements
Was this article helpful?