Fix and Furrow
Advertise

Sprinkler Precipitation Rate: How Long to Run Each Zone

Spray heads and rotors water at different speeds, so one timer setting can't fit every zone. Here's how to measure yours.

Save to Pinterest

We may earn a commission when you buy through links on this page. It never changes what we recommend. Learn more

Lawn sprinkler spray heads watering a green yard in morning light
Photo: Anastasiya Badun on Unsplash

The short answer

Run each zone long enough to deliver about 1 inch of water per week in the growing season, counting rain, split into one to three sessions. Divide the inches per session by your zone's measured precipitation rate, then multiply by 60 for minutes. Spray zones often apply 1.5 to 2 inches per hour; rotors often 0.4 to 0.8. Measure yours with a catch can test.

Typical cost
Under $10 for cans and a ruler; roughly $5 to $15 per replacement nozzle
Time needed
About 1 hour per zone, including setup and math
Skill level
Beginner

Key points

  • Sprinkler precipitation rate is the inches of water a zone applies per hour, and it differs a lot between spray heads and rotors.
  • A 15-to-30-minute catch can test with 6 to 10 straight-sided cans gives you a real number for each zone.
  • Run time in minutes equals target inches divided by inches per hour, times 60.
  • Zones that mix spray heads and rotors can't be fixed with run time alone; swap nozzles or split the valve.
  • Cut your weekly target in fall and check the soil before running a cycle.
In this guide
  1. What is sprinkler precipitation rate, and why does it matter?
  2. Why do spray heads and rotors need different run times?
  3. How do I run a catch can test on one zone?
  4. How do I convert catch can results into inches per hour?
  5. How do I calculate sprinkler run time from my target?
  6. What if a zone runs dry in the middle or puddles at the low end?
  7. When should I adjust run times through the fall?

The 15 or 20 minutes your timer started with is a guess, and it's usually wrong. A spray zone can put down about 0.4 inch of water in 15 minutes, while a rotor zone on the same setting delivers closer to an eighth of an inch. The only way to know what your zones do is to measure them. You need a few empty tuna cans and a ruler.

What is sprinkler precipitation rate, and why does it matter?

Sprinkler precipitation rate is the depth of water a zone applies in one hour, measured in inches, the same way a weather report measures rain. A rate of 1 inch per hour means the lawn gets an inch if the zone runs for 60 minutes and a half inch if it runs for 30. Once you know that number, run time becomes arithmetic instead of guesswork.

Grass responds to depth, not minutes. Most lawns do well on roughly 1 inch of water per week in the growing season, counting rainfall, though grass type, soil and climate shift that figure. Your local Cooperative Extension office can give you the number for your area.

Why do spray heads and rotors need different run times?

Spray heads and rotors need different run times because they apply water at very different speeds. Spray heads throw a wide fan a short distance and drop water fast, while rotors send a slower stream farther. Treat these ranges as ballpark figures and measure your own.

Head typeTypical inches per hourMinutes for 0.5 inch
Fixed spray head1.5 to 215 to 20
Gear-driven rotor0.4 to 0.838 to 75
Rotary nozzle0.4 to 0.650 to 75

Here's the mixed-zone trap. If spray heads and rotors share one valve, a 20-minute run puts about half an inch on the spray area and less than a fifth of an inch on the rotor area. Run it 60 minutes to satisfy the rotors and the spray area gets around 1.6 inches. Walk the zone while it runs: a fine fan on some heads and a rotating stream on others means you have a mix.

How do I run a catch can test on one zone?

Set straight-sided cans across the zone, run it for a timed cycle, and measure the water depth in each one. Tuna cans work well because they're flat-bottomed and straight-sided.

  1. Place 6 to 10 cans across the zone: some near heads, some midway between them, a few near the edges, and one or two in any spot that looks dry or soggy.
  2. Run only that zone for a set time, 15 minutes for spray heads or 30 for rotors, and note the exact minutes. Stop early if a can is about to overflow.
  3. Measure each can's depth with a ruler, to the nearest 1/16 inch, and jot down where each can sat.

How do I convert catch can results into inches per hour?

Average the depths from all the cans, then scale that average up to a full hour: average depth × (60 ÷ test minutes) = inches per hour. If your 15-minute spray test averages 0.4 inch, that's 0.4 × 4 = 1.6 inches per hour. A 30-minute rotor test averaging 0.25 inch gives 0.25 × 2 = 0.5 inch per hour.

Check the spread too. Average the driest quarter of your cans, then divide by the overall average. A result near 1.0 means even coverage. As a rough rule, anything below about 0.7 means water is landing unevenly, and the rate alone will mislead you.

How do I calculate sprinkler run time from my target?

Divide the depth you want per session by the zone's inches per hour, then multiply by 60 to get minutes. Aiming for 0.5 inch on the 1.6 inch-per-hour spray zone gives 0.5 ÷ 1.6 × 60, or about 19 minutes. The 0.5 inch-per-hour rotor zone needs 0.5 ÷ 0.5 × 60, or 60 minutes.

Two sessions a week at 0.5 inch hits the 1 inch target. We'd pick that over daily short runs for most lawns, because fewer, deeper waterings push roots down. Sandy soil and new sod may need more frequent, shorter runs. If clay soil or a slope makes water pool or run off before the time is up, split each session into two or three shorter cycles with an hour or so between them. Many controllers have a cycle-and-soak setting for exactly this.

What if a zone runs dry in the middle or puddles at the low end?

A dry band between heads usually means they sit too far apart, and a puddled low end usually means water is draining out of the lowest heads after shutoff. Good coverage depends on head-to-head coverage, where each head's spray reaches the next head. Spaced wider than their throw, heads leave a weak band between them, and extra minutes just overwater the spots near each head.

  • Clogged or tilted heads: clean or replace nozzles and straighten heads first. It's the cheapest fix.
  • Pressure: misting means pressure is too high and a short, weak throw means it's too low. A pressure regulator at the valve helps the first case.
  • Low-end drainage: check valves in the lowest heads hold water in the pipe so it can't spill out.
  • Mixed heads: swap in matched precipitation rate nozzles, such as rotary nozzles in place of fixed sprays, or split the zone onto a second valve.

When should I adjust run times through the fall?

Cut sprinkler run times once temperatures drop and days shorten, because grass uses far less water in cool weather. Re-run the math with a smaller weekly target, say 0.5 inch instead of 1 inch, then check the soil: if a screwdriver slides in easily 4 to 6 inches, skip the next cycle. A rain sensor or smart controller can automate some of this, but both still depend on the inches-per-hour number you measured.

Newly overseeded areas are the exception, since seed needs the top inch kept damp with short, frequent runs. If you're weighing seed against sod, see our overseeding vs sod comparison. When hard freezes approach, drain the lines with our guide to blowing out a sprinkler system safely. Wear eye protection and keep air pressure within your pipe's rating, or hire a pro.

Next step: test one zone this weekend, write its inches-per-hour number inside the controller door, and reset that zone's run time first.

Questions people ask

Can I use measuring cups instead of tuna cans?

Yes, as long as the container has straight sides so the water depth is the same at any level. Wide, shallow containers are easier to read with a ruler than tall, narrow ones.

How often should I repeat the test?

Repeat it after you change nozzles, move heads, or adjust pressure, and every couple of years otherwise. Heads sink, clog and wear, so the numbers drift.

Why do my cans collect wildly different amounts?

Usually it's poor spacing, clogged nozzles, pressure that's too high or too low, or wind on test day. Fix those before you set run times, because a big spread means part of the lawn is being starved or drowned.

Does a smart controller make this test unnecessary?

No. A smart controller adjusts run times for weather, but it needs an accurate precipitation rate for each zone to do the math. Some units fall back on generic values until you enter measured ones.

Should I water in the morning or evening?

Early morning is the usual pick, since wind and heat are low and the grass dries during the day. Evening watering leaves foliage wet overnight, which can invite lawn disease in humid climates.

Sources and further reading

Elsewhere in Gardening