Part of our Roofing and Exterior guide
Prehung Exterior Door Installation Mistakes to Avoid
Missing sill pans, bad shimming and overfilled foam are the errors to catch while they're still cheap to fix.
Save to PinterestWe may earn a commission when you buy through links on this page. It never changes what we recommend. Learn more
The short answer
The costliest prehung exterior door mistake is skipping the sill pan and flashing, which lets water rot the subfloor. Shimming in the wrong spots, trusting a level alone, overdriving screws and overfilling foam come next. Corrections often run a few hundred dollars, or thousands if water reaches the framing. Check plumb, diagonals and reveals before the foam cures.
- Typical cost
- Often a few hundred dollars to correct; thousands if the subfloor rots
- Time needed
- One day for a careful install, plus an overnight foam cure
- Skill level
- Intermediate
Key points
- Install a sill pan and lap flashing shingle-style, or water will find the subfloor.
- Shim only behind the hinges, strike plate and top corners, then check the gap around the slab.
- Measure both diagonals and the reveal, because a level alone won't tell you the frame is square.
- Use low-expansion foam sparingly and stop well short of filling the cavity.
- Test swing, latch and water before you trim, while changes are still easy.
In this guide
- What do the common mistakes cost?
- Why is skipping the sill pan and flashing the costliest mistake?
- Where should you shim a prehung door frame?
- Is a level enough to check a door frame?
- How do you fasten a door jamb without warping it?
- Can expanding foam really push a door frame out of square?
- What goes wrong with the threshold and weatherstripping?
- How do you test the door before trim goes on?
The worst door mistake is the one you can't see. A prehung exterior door can swing fine and still funnel water into the subfloor, and by the time a stain shows up the damage is usually done. Most of the errors below are cheap to avoid and expensive to undo, so check each one before the foam sets.
What do the common mistakes cost?
Most installation mistakes cost a few hundred dollars to fix, but water damage can climb into the thousands.
| Mistake | Typical consequence | Fix |
|---|---|---|
| No sill pan or flashing | Rotted subfloor and sill framing; repair can reach the thousands | Pan and lapped flashing tape |
| Wrong shim spots | Binding slab, latch misses strike plate | Shim at hinges and strike |
| Level only | Uneven reveal, drafts | Check plumb, diagonals, reveal |
| Overdriven screws | Bowed jamb, sticking | Snug, don't crank |
| Too much foam | Frame pushed out of square | Low-expansion, partial fill |
| Threshold ignored | Water and air under the door | Adjust the cap, check the sweep |
A carpenter hired to rehang and reflash a door commonly charges a few hundred dollars. It runs higher if siding, trim or subfloor has to come apart, and rates vary by region. Manufacturers can also deny warranty claims when the instructions weren't followed, so read yours before you start.
Why is skipping the sill pan and flashing the costliest mistake?
Skipping the sill pan lets wind-driven water travel under the threshold and into the subfloor, where it can rot framing for years before you see a stain.
It happens because the pan disappears once the door is in, and the packaging rarely makes a fuss about it. Build the pan before you set the unit. For a standard opening we'd pick a preformed pan, with flexible flashing tape as the alternative, and either way you want a back dam at the inside edge and slope toward the exterior. Run it up each side of the opening several inches. Then lay a continuous bead of polyurethane sealant along the sill and set the door into it. Flash the sides and head with tape, lapping every layer over the one below so water always sheds outward.
If the house predates 1978, the old casing and paint may contain lead. Read the EPA's lead renovation guidance before you pry anything off, and hire a lead-safe certified contractor if you're not doing the work yourself.
Where should you shim a prehung door frame?
Shim behind each hinge, behind the strike plate and near the top corners of the frame, and nowhere else.
People fill the whole jamb with shims because it feels thorough. Random shims create pressure points that bow the jamb and pinch the slab. Use cedar shims in opposed pairs so the stack sits flat, and place them at the fastener locations. Start on the hinge side and plumb it first. Then bring the latch side in to match the slab, with a consistent gap of roughly an eighth of an inch. A door that rubs at the top latch corner usually has a misplaced shim or a hinge jamb that isn't plumb.
Is a level enough to check a door frame?
No. A level confirms one plane at a time, and a frame can be plumb in one direction while twisted or racked in another.
Check the hinge jamb for plumb on its face and its edge. Measure the opening corner to corner; the two diagonals should match within about an eighth of an inch. Then trust the reveal, the gap between slab and jamb, which should be uniform along the head and sides.
A level on a sloped sill is the classic trap. If the subfloor drops toward the exterior, leveling the sill can tip the whole frame out of plumb. Correct the subfloor with proper shimming or underlayment instead of bending the frame to suit it. A frame that isn't square will bind, whistle and wear out its weatherstripping early.
How do you fasten a door jamb without warping it?
Drive fasteners through the jamb at the shim points only, and stop when the screw is snug, not when the clutch gives up.
Overdriving pulls the jamb toward the stud and squeezes the shim stack. Replace one short hinge screw per hinge with a 3-inch screw so it reaches the framing, and pre-drill to avoid splitting. A drill with an adjustable clutch helps. Recheck the reveal after every fastener, because a perfect gap before the screw and a pinched one after it is a common surprise.
Can expanding foam really push a door frame out of square?
Yes, standard high-expansion foam can bow a jamb enough to make a door bind, sometimes hours after you've walked away.
Use low-expansion foam made for windows and doors, fill the gap only about halfway, and work in short beads. Follow the can's instructions on bracing or spacing the jamb while it cures. Wear gloves and eye protection, because uncured foam is sticky and irritating. Foam seals air leaks, which the Department of Energy's Energy Saver guidance identifies as a common source of heating and cooling loss, but it isn't structural. If a door starts binding the next morning, foam is the usual cause, and planing the slab won't cure it.
What goes wrong with the threshold and weatherstripping?
An unadjusted threshold leaves a gap under the slab or crushes the sweep, and either one invites drafts and water.
Most prehung units have an adjustable threshold cap. Raise or lower it until the bottom sweep touches evenly across the full width, with light compression and no daylight. Slide a strip of paper through the weatherstripping at several points around the door; it should drag slightly everywhere. Confirm the sill slopes toward the outside, and that sealant runs under both ends of the threshold, because that's where leaks tend to start.
How do you test the door before trim goes on?
Open and close the door several times, test the latch, and spray the exterior with a hose before any trim or caulk hides a problem.
Swing the slab open to about 45 degrees and release it. It should stay put, not drift. Latch it without pushing and check that the bolt enters the strike plate smoothly. Then run a hose across the door and threshold for a few minutes while someone watches the inside edges with a flashlight. This is the moment to fix an exterior door water leak, when a bead of sealant or a re-lapped flashing strip takes minutes instead of a demolition.
Write down each reveal measurement before you buy trim. If anything is off, fix it now, not after the paint is dry.
Questions people ask
Can I install a prehung exterior door by myself?
A careful DIYer can, but many exterior doors weigh well over 100 pounds, so have a helper for setting it. The tricky parts are flashing and shimming, not carrying. If the opening needs framing changes, hire a pro.
How do I know if my new door is leaking at the bottom?
Look for dampness at the interior threshold ends after rain, or press on the subfloor near the sill for softness. A hose test with a helper watching inside is the fastest check. Fix it early, since slow leaks do most of their damage out of sight.
Why does my door stick after I installed it?
Usually the hinge jamb isn't plumb, a shim is in the wrong place, or foam bowed the frame. Check the reveal around the slab to find where it rubs. Loosen the nearest fasteners and re-shim before you plane the door.
Should I remove the shims after the foam cures?
No. Leave the shims at the hinges and strike plate in place and trim them flush, since they carry the door's weight. Foam only seals air gaps.
Do I need a permit to replace an exterior door?
Like-for-like swaps often don't need one, but rules vary by town, and changing the opening size usually does. Call your local building department before you start.
Sources and further reading
- U.S. Dept. of Energy, Energy Saver Air sealing and door guidance for energy savings
- EPA Lead (Renovation, Repair and Painting) Lead-safe renovation rules for homes built before 1978
- National Association of Home Builders Residential building industry resources and standards
Was this article helpful?